User's Manual
Table Of Contents
- T3CAS_Section_5
- 5 Adjustment/Test
- 1. General
- 2. Equipment
- 3. Initial Harness Checkout (New Installations Only)
- 4. System Self-Tests
- 5. Return-to-Service Test
- 6. Operational Software Loading Using an ARINC 615A Portable Data Loader or Compact Flash Card
- 7. Downloading Information from the TP3PCAS Using a CF Card
- 1. Obtain a New or Blank Compact Flash (CF) card.
- 2. Copy to the New or Blank CF card the appropriate ‘Header File’
- a) Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- b) Header files needed to download Maintenance Data, Event Data and CRC Part Numbers can be obtained from ACSS Customer Services at +1-623-445-7070 or crc.acss@l-3com.com.
- 3. For downloading Maintenance Data, Event Data or CRC Part Numbers the aircraft does not need to be in an on-ground configuration.
- 4. Apply power to the computer unit.
- 5. Insert the CF card.
- 6. For ACSS part numbers 9005000-10000, -10101, -10202, and -10204 the DATA STATUS LED will UblinkU green once; this indicates the unit recognized that a CF card was inserted.
- 7. For ACSS part numbers 9005000-11203, -11801 and -55801 the DATA STATUS LED will UblinkU green while reading the header file and performing the action defined in the header file.
- 8. Flight Data Recording
- 1. T3CAS part numbers 9005000-10000, -10101, -10202, and -10204 only support FAT16 CF card formatting. T3CAS part numbers 9005000-11203, -11801 and -55801 support both FAT16 and FAT32 CF card formatting.
- B. Flight Data
- 1. Obtain a New or Blank CF Card.
- 2. Copy to the New or Blank CF Card the Appropriate Header File.
- 3. Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- 4. For Flight Data Recording, the aircraft does not need to be in an on-ground configuration.
- 5. Apply power to the computer unit.
- 6. Insert the CF card.
- B. Flight Data
- 9. Downloaded Maintenance Data, Event Data And Flight Data May Be Sent To ACSS Customer Services For Analysis
- 5 Adjustment/Test
- T3CAS_Section_6
- T3CAS_Section_7
- 7 Maintenance Practices
- 1. General
- 2. Equipment and Materials
- 3. Procedure for the TP3PCAS Computer Unit
- 4. Procedure for the APM (Not applicable for part numbers 9005000-10000, -10101, -10202, -10204, or -11203)
- 5. Procedure for the Directional Antenna
- 6. Procedure for the Omnidirectional Antenna (Applicable to part numbers 9005000-11203, -11801 and -55801)
- 7. Procedure for the Control Panel
- 8. Procedure for the VSI/TRA Display
- 9. Instructions for Continued Airworthiness, FAR Part 25.1529
- 7 Maintenance Practices
- T3CAS_Section_8
- T3CAS_Section_9
- T3CAS_Section_10
- T3CAS_Appendix_A
SYSTEM DESCRIPTION AND INSTALLATION MANUAL
T
3
CAS/Part No.9005000
Table 4-17: DO-260B Configuration Pins
(Applicable to Part Numbers 9005000-11203, -11801, -55801)
All
OPEN
RTP-13B
TAWS/XPDR
Out #1
RTP-13C
TAWS/XPDR
Out #2
RTP-13D
TAWS/XPDR
Out #3
RTP-12A
DO-260B
Config Data #1
Aircraft Vehicle Length/Width bit 0
Aircraft Vehicle Length/Width bit 1
Aircraft Vehicle Length/Width bit 2
0
0
0
0
0
1
0
1
0
0
1
1
RTP-12B
DO-260B
Config Data #2
Aircraft Vehicle Length/Width bit 3
GPS Antenna Longitudinal Offset bit 0
GPS Antenna Longitudinal Offset bit 1
0
0
0
0
0
1
0
1
0
0
1
1
RTP-12C
DO-260B
Config Data #3
GPS Antenna Longitudinal Offset bit 2
GPS Antenna Longitudinal Offset bit 3
GPS Antenna Longitudinal Offset bit 4
0
0
0
0
0
1
0
1
0
0
1
1
RTP-12D
DO-260B
Config Data #4
NACv bit 0
NACv bit 1
SDA bit 0
0
0
0
0
0
1
0
1
0
0
1
1
RTP-12E
DO-260B
Config Data #5
SDA bit 1
Aircraft Category bit 0
Aircraft Category bit 1
0
0
0
0
0
1
0
1
0
0
1
1
RTP-12F
DO-260B
Config Data #6
Aircraft Category bit 2
ADS-B FAIL Disable bit 0
ADS-B Receive Capability bit 0
0
0
0
0
0
1
0
1
0
0
1
1
RTP-9J
DO-260B
Config Data #7
ADS-B Receive Capability bit 1
VFOM Adjust bit 0
VFOM Adjust bit 1
0
0
0
0
0
1
0
1
0
0
1
1
RTP-9K
DO-260B
Config Data
Parity
NOTE: If the number of DO-260B Config
Data #1 through #7 pins connected is
even, connect RTP-9K to RTP-13B, else
RTP-9K should be left Open.
If Odd Parity
If Even Parity
N/A
N/A
RTP-13E
TAWS/XPDR
Out #4
RTP-13F
TAWS/XPDR
Out #5
RTP-13G
TAWS/XPDR
Out #6
RTP-13H
TAWS/XPDR
Out #7
RTP-12A
DO-260B
Config Data #1
Aircraft Vehicle Length/Width bit 0
Aircraft Vehicle Length/Width bit 1
Aircraft Vehicle Length/Width bit 2
1
0
0
1
0
1
1
1
0
1
1
1
RTP-12B
DO-260B
Config Data #2
Aircraft Vehicle Length/Width bit 3
GPS Antenna Longitudinal Offset bit 0
GPS Antenna Longitudinal Offset bit 1
1
0
0
1
0
1
1
1
0
1
1
1
RTP-12C
DO-260B
Config Data #3
GPS Antenna Longitudinal Offset bit 2
GPS Antenna Longitudinal Offset bit 3
GPS Antenna Longitudinal Offset bit 4
1
0
0
1
0
1
1
1
0
1
1
1
RTP-12D
DO-260B
Config Data #4
NACv bit 0
NACv bit 1
SDA bit 0
1
0
0
1
0
1
1
1
0
1
1
1
RTP-12E
DO-260B
Config Data #5
SDA bit 1
Aircraft Category bit 0
Aircraft Category bit 1
1
0
0
1
0
1
1
1
0
1
1
1
RTP-12F
DO-260B
Config Data #6
Aircraft Category bit 2
ADS-B FAIL Disable bit 0
ADS-B Receive Capability bit 0
1
0
0
1
0
1
1
1
0
1
1
1
4-118
04 Nov 2014
34-45-29
Pub. No. 8600200-001, Revision 004
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.