User’s Manual Wireless Presenter with Laser Pointer Page
Regulatory Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Certification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
• Consult the dealer or an experienced radio/TV technician for help. Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Extension cables are not recommended, if used, they must be shielded in order to comply with the emission limits. IC Certification The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications were met.
System Requirements Hardware: 1 available USB port Operating System: Windows 2000, XP or Vista Macintosh OS X or above (F5 SlideShow and Alt-Tab Application Switch not supported) Package Contents • • • • • Wireless 2.
• Open the battery compartment by pressing down the cover latch and sliding the door off the presenter. • Insert the two supplied AAA batteries (included in the package) to the battery slots. Make sure the positive (+) and negative (-) ends of the batteries match the polarity markings inside the battery compartment. • Close the battery cover back into position.
• Connect the micro USB receiver dongle to an available USB port on your computer. Wait for the computer to go through its default process of recognizing the new hardware and installing the built-in native driver. You don’t need to do anything while your computer is going through the installation of a new device. • Power on the presenter by sliding the on/off switch to ON position.
• The radio frequency (RF) codes are factory preset for your convenience; the presenter should be functional at this point. • If for any reason the presenter does not function correctly, i.e. the presentation slides do not advance to the next page, there may be other wireless devices in the vicinity operating in the same radio frequency channel.
Connect Button (1) Press the connect button on the receiver (2) Press the connect button on the presenter Using the Presenter Laser Beam Dongle Storage On/off Application Switch Previous Page Dark Screen Scroller Laser Pointer Next Page Slideshow/Esc Page
• F5/Esc Slideshow toggle key starts a slideshow (F5) and exits from a slideshow (Esc). Note: in PowerPoint slideshow starts with page 1 when resumed in the middle of a presentation. • Next Page key to advance to the next slide. • Previous Page key to return to the previous slide. • Application Switch (Alt-Tab) key displays all the open windows and switches to the desired window by pausing over the selected window icon for 3 seconds.
• Scroller on the side allows the presentation of a long document such as an Excel file. Scrolling one notch up or down advances one line at a time. To advance in rapid mode press up or down on the scroller for more than 1 second at a time. In PowerPoint the scroller serves as an alternative key for Next Page and Previous Page. Operating Tips & Trouble Shooting • Make sure the presenter is turned on by checking the on/off switch located at the side of the presenter before using it.
• The presenter stays connected to your computer even when it’s turned off. If for any reason the connection to the system is lost or interference is detected (erratic slide control), first check if the micro USB receiver dongle is plugged in to the computer USB port, then verify that the presenter is within the range (up to 70 feet) from your computer. If the connection is lost it can be fixed by following the instructions in the Connecting the Presenter to the Computer section to reconnect the devices.
for warranty service consideration. Any Product repaired or replaced under the terms of the warranty is covered for the remainder of the original warranty period or ninety (90) days from the date of service or return shipping, whichever is longer. If the Product becomes defective in materials or workmanship during the warranty period, SMK-LINK Electronics will, at its option, either repair or replace it with a more current or upgraded model if the originally purchased model is not available.
warranty is understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral or written, and all other communications between the parties relating to the subject matter of this warranty.
Thank You Thank you for purchasing the Wireless Presenter with Laser Pointer. We know you had other choices and we appreciate that you chose Interlink Electronics Wireless Presenter by SMK-LINK for your product needs. So that we may better serve you in the future, please register online at www.smklink.com/ register.
