AR-B6050 User Manual AR-B6050 Board Fan-less with Intel ATOM Pineview + ICH8M User Manual Manual Rev.: 1.0 Book Number: AR-B6050-2010.07.
AR-B6050 User Manual Revision Version Date Author 1.
AR-B6050 User Manual Copyright 2010 All Rights Reserved. Manual’s first edition: For the purpose of improving reliability, design and function, the information in this document is subject to change without prior notice and does not represent a commitment on the part of the manufacturer.
AR-B6050 User Manual Table of Contents 1 Introduction ............................................................................. 5 1.1 Specifications.................................................................................................6 1.2 Package Contents ..........................................................................................7 1.3 Block Diagram ................................................................................................8 2 H/W Information.............
AR-B6050 User Manual 1 INTRODUCTION AR-B6050 is a 3.5” SBC board that is designed with Intel Atom N450 and supports up to 2GB of DDR2 667Mhz memory. AR-B6050 has diverse physical interface for different peripheral, e.g. VGA port, LVDS port, 6 * USB 2.0 ports, 2 * COM ports, 2 * Gbps ports, 2 * SATA ports, CF type I/II slot and Realtek audio output port. It is also equipped with industrial standard PCI-104 and miniPCIe interface. Users can purchase suitable add-on cards to satisfy their needs.
AR-B6050 User Manual 1.1 Specifications IntelR Atom N450 1.66GHz IntelR Graphics Media Accelerator 950 1 x SO-DIMM supports DDRII up to 2GB(Memory DDR2 data transfer rates of 667 MT/s) 1 x VGA 4 x USB2.
AR-B6050 User Manual 1.2 Package Contents Check if the following items are included in the package.
AR-B6050 User Manual 1.
AR-B6050 User Manual 2 H/W INFORMATION This chapter describes the installation of AR-B6050. At first, it shows the Function diagram and the layout of AR-B6050. It then describes the unpacking information which you should read carefully, as well as the jumper/switch settings for the AR-B6050 configuration 2.1 Locations of Connector and Jumper Setting 2.1.
AR-B6050 User Manual JP1 COM1 VGA1 ATX1 COM2 J1 BAT1 SATA2 USB3 SYSFAN1 SATA1 USB1 CN2 CN4 USB2 CN3 JP3 LED1 JP2 LAN1 LVDS1 J7 LAN2 CN1 GPIO1 J6 10
AR-B6050 User Manual 2.1.
AR-B6050 User Manual 2.2 Connector and Jumper Setting Table 1. JP1: LCD panel driving voltage selection. STATUS 2. ATX1: AT power input connector. 3. BAT1: CMOS battery holder. PIN SETTING 1 GND 2 GND 3 +12V 4 +12V SETTING +3.3V 1-2 CMOS battery holder. (Default). 2-3 +5V 4. SYSFAN1: System DC Fan connector. PIN SETTING 1 GND 2 +12V 3 Fan speed data 5. CN2: PCI-104 connector. PCI-104 connector. 7. JP2: Signal SERIRQ 8.
AR-B6050 User Manual 10. COM1: RS232 signal connector for port #1. 11. COM2: RS232 signal connector for port #2. PIN SETTING PIN SETTING 12. SATA1: SATA device connector #1. PIN SETTING PIN SETTING 1 DCD #1 2 DSR #1 1 DCD #2 2 DSR #2 3 RX #1 4 RTS #1 3 RX #2 4 RTS #2 SATA device connector 5 TX #1 6 CTS #1 5 TX #2 6 CTS #2 #1. 7 DTR #1 8 RI #1 7 DTR #2 8 RI #2 9 GND 10 GND 9 GND 10 GND 13. SATA2: SATA device connector #2. 14. CN4: Audio signal connector.
AR-B6050 User Manual 19. VGA1: D-SUB-15 female 20. J1: CMOS data clear connector for VGA output. 21. USB3: Internal USB2.0 connector PIN SETTING PIN SETTING D-SUB-15 female connector for VGA output. 22. USB1: USB connector 1 +5V 2 +5V 3 USB5- 4 USB6- 5 USB5+ 6 USB6+ 7 GND 8 GND 9 GND 10 GND SHORT CMOS data clear 23. USB2: USB connector 24. LED1: System power and HDD access indicators. Green: System power Upper: Port #2. Upper: Port #4. indicator. Lower: Port #1.
AR-B6050 User Manual 27. DIMM1: DDR-II SODIMM Socket. 28. CF1: Type-II compact flash card socket. DDR-II SODIMM +3.3V CF card only and Socket. UDMA mode supported.
AR-B6050 User Manual 3 BIOS SETTING The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS. To activate the BIOS Utility, press F2 during POST (when “Press to enter Setup” message is prompted on the bottom of screen). Press during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility.
AR-B6050 User Manual 3.1 Main Setup Once you enter the InsydeH2O BIOS™ Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to highlight the item and then use the keys to select the desired value in each item. Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item System Date System Time Processor Type Option Description Set the system date.
AR-B6050 User Manual This field displays the bus speed of the System Bus Speed N/A System Memory Speed N/A This field displays the real speed of the memory. Cache RAM N/A This field displays the cache ram of the CPU. Total Memory N/A Displays the total memory available. SODIMM 0 N/A This field displays the memory of the SODIMM0. BIOS Revision N/A Displays system BIOS version. system.
AR-B6050 User Manual 3.2 Advanced Chipset Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item Peripheral Configuration IDE Configuration Option Description Serial Port A Serial Port B Azalia Audio control Enter the Peripheral Configuration menu. IDE Controller HDC Configure as Enter the IDE Configuration menu.
AR-B6050 User Manual 3.3 Peripherals Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item Option Supervisor Password Not Installed Installed Description Shows the setting of the Supervisor password Press Enter to set the user password. When user password is set, this password protects the Set Supervisor Password N/A BIOS Setup Utility from unauthorized access.
AR-B6050 User Manual Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: 2. Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.
AR-B6050 User Manual 3.4 Power Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item Option ACPI S3 Support Enabled Wakeup on PME Disabled Enabled Disabled Description ACPI S1/S3 Sleep State. Wake up when the system power is off and a PCI Power Management Enable wake up event occurs.
AR-B6050 User Manual 3.5 Boot Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item Option Description Select Boot Devices to select specific devices to support boot. Boot Device Priority N/A Hard disk Drive N/A Show the Hard disk drives. (The item can't display when no device.) CD/DVD-ROM Drive N/A Show the CD/DVD-ROM drives.
AR-B6050 User Manual 3.6 Exit Setup Note: The control keys are listed at the bottom of the menu. If you need any help with the item fields, you can press the key, and the relevant information will be displayed. Item Option Exit Saving changes Yes Save change without Exit Yes NO Save Your changes and without exiting system. Yes Exit system setup and without saving your NO changes. Exit Discarding changes NO Description Exit System Setup and save your changes.
AR-B6050 User Manual WATCHDOG, GPIO, AND BYPASS 4 PROGRAMMING 4.1 Watchdog Programming This section describes the usage of WATCHDOG. AR-B6050 integrated the WATCHDOG that enable user to reset the system after a time-out event. User can use a program to enable the WATCHDOG and program the timer in range of 1~255 second(s)/minute(s). Once user enables the WATCHDOG, the timer will start to count down to zero except trigger the timer by user’s program continuously.
AR-B6050 User Manual -o 2F ## The value “##” ranges between 01 ~ FF (1 ~ 255 seconds). 00: To disable WATCHDOG. -q To quit debug mode Notice: The “actual” timer value may not match with the “theoretical”. That is because of the tolerance of internal oscillating clock and cannot be adjusted or optimized.
AR-B6050 User Manual // Main procedure //========================================================================= == int main(int argc, char *argv[]) { unsigned char IO_Port_Address=0x2E; unsigned char Time; unsigned char Temp; if ( argc != 2 ) { Show_Help(); return 1; } clrscr(); Time=atoi(argv[1]); // Set Watchdog outportb(IO_Port_Address,0x87); // (EFER) Extended Functions Enable Register outportb(IO_Port_Address,0x87); outportb(IO_Port_Address,0x2D); // Point to Global Reg.
AR-B6050 User Manual for(Temp=Time;Temp>0;Temp--) { outportb(IO_Port_Address,0xF6); // Read Watchdog Timer Value Time=inportb(IO_Port_Address+1); gotoxy(20,10); cprintf(">>> After %3d Second will reset the system.
AR-B6050 User Manual 4.2 GPIO Programming This section describes the usage of GPIOs. AR-B6050 integrated eight bits, 5V TTL level, bidirectional, and software programmable GPIOs for user’s application. They are all capable of 5 mA source current for output and 8 mA sink current for input individually.
AR-B6050 User Manual == #include #include
AR-B6050 User Manual =======<>"); gotoxy(1, 4); cprintf("<>=================================================================== =======<>"); gotoxy(1, 5); ||"); gotoxy(1, 6); ||"); cprintf("|| Model Name : cprintf("|| SIO IO Base : gotoxy(1, 7); cprintf("<>=================================================================== =======<>"); // Show Got Parameter Informat textcolor(LIGHTGRAY); gotoxy(18,5); cprintf("%s",Model_Name); gotoxy(18,6); cprintf("%X",IO_PORT_BASE); // Enter W83627EHF Config outportb
AR-B6050 User Manual outportb(IO_PORT_BASE,0xF0); outportb(IO_PORT_BASE+1,0xF0); // Set W83627EHF GPIO10~13 to High outportb(IO_PORT_BASE,0xF1); outportb(IO_PORT_BASE+1,0x0F); // Read W83627EHF GPIO14~17 Status, if not High error. data=inportb(IO_PORT_BASE+1)&0xF0; if(data!=0xF0) result=1; // Set W83627EHF GPIO10~13 to Low outportb(IO_PORT_BASE,0xF1); outportb(IO_PORT_BASE+1,0x00); // Read W83627EHF GPIO14~17 Status, if not Low error.
AR-B6050 User Manual outportb(IO_PORT_BASE,0xAA); if(result) Show_Fail(); else Show_Pass(); return result; } //========================================================================= == // Function // Input : // Change : Show_Help() :- // Return : // Description : Show Title string.
AR-B6050 User Manual == void Show_Fail() { textcolor(LIGHTRED); gotoxy(20,10); cprintf(" 詗詗詗詗 gotoxy(20,11); gotoxy(20,12); gotoxy(20,13); gotoxy(20,14); cprintf(" cprintf(" cprintf(" cprintf(" 詗 詗詗詗 詗 詗 詗詗詗 詗詗 詗 詗 詗 詗詗詗詗 詗 詗 詗 詗 詗 詗 詗 詗詗 詗 "); 詗 "); 詗 "); 詗詗詗詗"); "); } //========================================================================= == // Function // Input : - : Show_Pass() // Change :// Return : // Description : Show Pass Message.
