AR-B5630 Socket P Intel® Core™2 Duo EPIC SBC with Intel® GME965 Express Chipset , DVI/LCD, Dual LAN and PCI-104 Eexpansion User Guide Edition: 1.0 Book Number: AR-B5630 08.10.
Table of Contents 0. PREFACE.....................................................................................................................................................................4 0.1 COPYRIGHT NOTICE AND DISCLAIMER .....................................................................................................................................4 0.2 WELCOME TO THE AR-B5630 CPU BOARD.............................................................................................................
5.4 PNP/PCI SETUP ...........................................................................................................................................................................29 Thus field allows you to determine whether to reset the configuration data or not. The default value is “Disabled”.29 5.5 PERIPHERALS SETUP ................................................................................................................................................................30 5.
0. PREFACE 0.1 COPYRIGHT NOTICE AND DISCLAIMER This document is copyrighted, 2008, by Acrosser Technology Co., Ltd. All rights are reserved. No part of this manual may be reproduced, copied, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, such as electronic, mechanical, magnetic, optical, chemical, manual or other means without the prior written permission or original manufacturer.
0.6 STATIC ELECTRICITY PRECAUTIONS Before removing the board from its anti-static bag, read this section about static electricity precautions. Static electricity is a constant danger to computer systems. The charge that can build up in your body may be more than sufficient to damage integrated circuits on any PC board. It is, therefore, important to observe basic precautions whenever you use or handle computer components.
1. INTRODUCTION Welcome to the AR-B5630 ECIP AT/ATX Single Board Computer. The AR-B5630 is EPIC board with Socket P Intel Core™2 Duo or Core Duo or Core Solo and Celeron M processor and Intel GM965 + ICH8M Chipset. The memory contents one DDR2 SO-DIMM socket which supports up to 2GB of memory. Graphics display functionality is provided by Build-in Graphic Processor that supports CRT display and LVDS interface with Single or Dual channel panel specifications.
1.2 SPECIFICATIONS Specifications (Proposed Specifications) Model Name AR-B5630 Product EPIC SBC support 65nm Intel uFC-PGA 478 Core 2 Duo/Core Duo/Core Solo/Celeron M V 1.0 Descriptions Processors with Dual Gigabit LANs / LCD / TV out / DVI General Note CPU Socket for Intel uFC-PGA 478 Core 2 Duo/Core Duo/Core Solo/Celeron M, Coolers required.
I/O 1 x RS-232 (COM1) DB9 Serial Port 2 x RS-232 (COM3/4) Pin Header Touch Screen N/A Parallel Port N/A GPIO 8 Independent TTL level I/O 1 x RS-232/422/485 (COM2) PinHeader (2x5x2.0) USB 2 x External ports Connector 2 x Internal ports Pin Header (1x5x2.0) IrDA 1XIR PinHeade Audio 5.1 CH Audio Pin Header Expansion slot 1 x PCI-104 (PCI Interface) Slot Keyboard/ Mouse 1 x PS/2 for Keyboard and Mouse Connector Mechanical Dimension 115mm x 165mm (4.528 x 6.
1.
2. INSTALLATION This chapter describes how to install the AR-B5630. At first, the layout of AR-B5630 is shown, and the unpacking information that you should be careful is described. The jumpers and switches setting for the AR-B5630’s configuration are as below. 2.
3. CONNECTION The connectors on AR-B5630 allows you to connect external devices such as USB devices, serial port drives, hard disk devices, etc. The following table lists the connectors on AR-B5630 and their respective functions. 1. AT 2. ATX 3. SATA POWER 4. SERIRQ CONNECTOR 5. CPU FAN CONNCTOR 6. PCI 104 CONNECTOR 7. SATA CONNECTOR 8. IDE 9. KB_CLK CONNECTOR 10. CF MASTER SELECT 11. COMS BAT CONNECTOR 12. COMSCLACER CONNECTOR 13. KB/MS 14. INTERNAL USB CONN 15. USB CONNECTOR 16. LAN2 17. LAN1 18. VGA 19.
1.DDR2ONNECTOR 2.
3.1 AT POWER INPUT (PWR2) SET 1 SIGNAL GND 2 GND 3 +12V 4 +12V 3.2 ATX FUNCTION CONNECTOR (CON2) SET 1 SIGNAL GND 2 PS_ON 3 +5V_SUS 3.3 SATA POWER (CON3) 3.
3.5 CPU FAN (FAN1) PIN 1 SIGNAL GND 2 +12V 3 SENSE 3.6 PCI104 (J10) 3.
3.8 PATA CONNECTOR (IDE1) Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal -RESET DATA 7 DATA 6 DATA 5 DATA 4 DATA 3 DATA 2 DATA 1 DATA 0 GROUND PDDREQ -PDIOW -PDIOR PIORDY -PDDACK Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 31 IRQ14 32 33 PDA1 34 35 PDA0 36 37 -PDCS1 38 39 HLEDP 40 Signal GROUND DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 DATA 13 DATA 14 DATA 15 N.C GROUND GROUND GROUND GROUND GROUND N.C PD66/100 PDA2 -PDCS3 GROUND 3.9 KEYBOARD LOCK (J11) 3.
3.11 BATTERY CONNECTOR (BAT1) 3.12 COMS CLAER CONNECTOR(J5) 3.13 EYBOARD/MOUSE CONNECTOR (KM1) KM 1 2 3 4 5 6 KDT MDT GND VCC KCLK MCLK 1 2 3 4 6 5 Front View 3.14 INTERNAL USB CONNECTOR (USB2) PIN 1 3 5 7 9 SIGNAL +5V USB0USB0+ GND GND 3.
3.16 RJ45 CONNECTOR (LAN2) 8 PIN (LAN1 1 FUNCTION 1 TPTX+ 2 TPTX - 3 TPRX+ 4 Not Used 5 Not Used 6 TPRX - 7 Not Used 8 Not Used 3.17 RJ45 CONNECTOR (LAN1) 8 PIN (LAN1 1 FUNCTION 1 TPTX+ 2 TPTX - 3 TPRX+ 4 Not Used 5 Not Used 6 TPRX - 7 Not Used 8 Not Used 3.
PIN 1 2 3 4 5 6 7 8 SIGNAL RED GREEN BLUE NC GND GND GND GND PIN 9 10 11 12 13 14 15 SIGNAL +5V GND NC SDA HSYNC VSYNC SCL 3.19 DVI-I CONNECTOR (DVI1) PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 SIGNAL GND TD0TD1+ GND TD2TCK+ HPD VCC RED GREEN BLUE VSYNC HSYNC PIN 26 25 24 23 22 21 20 19 18 17 16 15 14 SIGNAL TD0+ GND TD1TD2+ GND TCKSCL1 SDATA1 GND GND GND SCL2 SDATA2 3.
3.21 COM2 (COM1) PIN 1 3 5 7 9 SIGNAL /DCDB RXDB TXDB /DTRB GND 3.22 COM1 (CON1) PIN 1 3 5 7 9 SIGNAL /DCDB RXDB TXDB /DTRB GND PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB 3.
3.24 COM4 (COM3) PIN 1 3 5 7 9 SIGNAL /DCDB RXDB TXDB /DTRB GND PIN 2 4 6 8 SIGNAL /DSRB /RTSB /CTSB /RIB 3.25 SYSTEM FAN (FAN2) PIN 1 SIGNAL GND 2 CONTROL 3 SENSE 3.26 AUDIO CONNECTOR (AUDIO1) PIN 1 3 5 7 9 11 13 15 SIGNAL LINE OUT R GND LINE IN R GND N/A GND N/A N/A 20 PIN 2 4 6 8 10 12 14 16 SIGNAL LINE OUT L N.A LINE IN L N.
3.27 PANEL POWER SELECTOR (J1) SET 1-2 SIGNAL 3.3V 2-3 5V 3.28 GPIO (GPIO1) PIN 1 3 5 7 9 SIGNAL GPIO0 GPIO1 GPIO2 GPIO3 GND 3.
3.30 RS422/RS485 CONNECTOR (J9) SET 1 SIGNAL TX+ 2 TX- 3 RX+ 4 RX- 3.31 IR CONNECTOR (IR1) 3.32 PANEL POWER SELECTOR (J1) SET 1-2 SIGNAL 3.3V 2-3 5V 3.
3.34 LVDS CONNECTOR (LCD1) 3.35 DDR2 SO-DIMM (DDR1) 3.
4. WATCHDOG TIMER CONFIGURATION 4.1 WATCHDOG TIMER SETTING The WDT (Watch Dog Timer) is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
// Set Watchdog outportb(IO_Port_Address,0x07); // Point to Logical Device Number Reg.
5. BIOS CONSOLE This chapter describes the AR-B5630 BIOS menu displays and explains how to perform common tasks needed to get up and running, and presents detailed explanations of the elements found in each of the BIOS menus. The following topics are covered: Main Setup Advanced Chipset Setup Power Setup Peripherals Setup PnP/PCI Setup PC Health Setup Boot Setup Exit Setup 5.
Time Setup The time format is： Hour：0 to 24 Minute：00 to 59 Second：00 to 59 To set the time, highlight the “Time” field and use the 【PageUp】/【PageDown】or 【+】/【-】keys to set the current time. IDE Primary HDDs⁄IDE Secondary HDDs The onboard PCI IDE connectors provide primary and secondary channels for connecting up to four IDE hard disks or other devices. Each channel can support up to two hard disks; the first is the “Master” and the second is “Slave”. Press＜Enter＞ to configure the hard disk.
Hyper-Threading Technology To enable HT Function Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enable, BIOS will skip some items. Full Screen LOGO Show The options for this field are “Enabled” and “disabled”. By default, the field is set to “Disabled” ACPI Mode APIC stands for Advanced Programmable Interrupt Controller. The default setting is Disabled.
ACPI Function Enable this function to support ACPI (Advance Configuration and Power Interface) ACPI Suspend Type This options for this field are S1 (POS) and S3 (STR). By default, the field is set to S1 (POS) PWRON After PWR-Fail The field sets the system power status whether on or off when power returns from a power failure. Power –Supply Type This item allows you to choose the Type of Power Supply in use.The Choice: AT, ATX. 5.4 PNP/PCI SETUP The option configures the PCI bus system.
5.5 PERIPHERALS SETUP This option controls the configuration of the board’s chipset. Control keys for this screen are the same as for the previous screen. Peripherals Setup Onboard Serial Port 1 Onboard Serial Port 2 Onboard Serial Port 3 Onboard Serial Port 4 These fields allow you to select the on board serial ports and their addresses.
5.6 PC HEALTH SETUP This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds, voltages. PC Health Status Temperature / Voltage These fields are parameters of the hardware monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. 5.7 BOOT SETUP This section is used to exit the BIOS main menu.
First / Second / Third Boot Device These fields determine the device that the system searches first for an operating system. The option available include Hard Disk, CDROM, USB-FDD, USB-CDROM and Disable. Boot Other Device These fields allow the system to search for an OS from other devices other than the ones selected in the First / Second / Third Boot Device. LAN Boot Select These fields allow the system to search for an OS from LAN.
5.9 BIOS UPDATE The BIOS program instructions are contained within computer chips called FLASH ROMs that are located on your system board. The chips can be electronically reprogrammed, allowing you to upgrade your BIOS firmware without removing and installing chips. The AR-B5630 provides the FLASH BIOS update function for you to easily to update to a newer BIOS version. Please follow these operating steps to update to new BIOS： Step 1: Turn on your system and don’t detect the CONFIG.SYS and AUTOEXEC.
