ANR-IH61N1/A/B System Manual 1
Copyright All Rights Reserved. Manual’s first edition: For the purpose of improving reliability, design and function, the information in this document is subject to change without prior notice and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Table of Contents Chapter 1 Introduction ......................................................................... 5 1.1 System Specifications ........................................................................................................ 5 1.2 1.3 1.4 Packing List........................................................................................................................ 8 Features .......................................................................................................
5.2.2. W83627DHG Super IO Configuration ......................................................... 36 5.2.3. Serial Port Console Redirection.................................................................. 40 5.2.4. Intel(R) 82576 Gigabit Dual Port Network Connection .......................... 41 5.2.5. Intel(R) 82574L Gigabit Network Connection .......................................... 42 5.3. HW Monitor Setup ................................................................................................
Chapter 1 Introduction ANR-IH61N1 is designed for rack-mounted platform for networking appliance, e.g. VPN, SSL, UTM or firewall. With 3rd Generation Intel Core i7/i5/i3 Processors / Pentium CPU, It is a powerful platform to satisfy different applications. By eight 10/100/1000Mbps LANs, the ANR-IH61N1 is sufficient for the small to middle size business security solution. ANR-IH61N1 can install 2 x HDD,BIOS and Jumper can control LAN bypass feature. It provides flexibility to access Internet by user setting.
Ethernet 6 * RJ45 and 0/2/4 * SFP LAN by-Pass 1. 2. LAN1/LAN2, LAN3/LAN4 support by-pass Reserve 1*3 pin Jumper for Hardware select bypass status I/O Front panel Internal I/O From left to right: 1. LCM module 2. Up, Down, Left, Right key pad 3. Reset Button 4. Power LED/HDD/bypass 1 & 2 : Green/Green/Yellow/Yellow 5. 0/2/4 SFP (F1~F4) 6. COM port (RJ45) 7. 2 * USB 2.0 8. LAN 6/5/4/3/2/1 1. 2. 3. 4. 5. LCM pin header(7-pin pinhead 2.54mm ) ATX 24pin Power input 1*8 pin 2.
Temperature Storage Temperature -20~80oC (-4~176oF) Relative Humidity 0 to 90% @ 40°C, non-condensing Power supply Standard ATX power (250W~300W) Power Requirements ATX circuit as AT mode with power switch EMC & Safety EMC CE, FCC Class A Safety EN 60950-1:2006/A12:2011 7
1.2 Packing List Check if the following items are included in the package. Model Name ANR-IH61N1/A/B Part Lists QTY ANR-IH61N1/A/B system 1 Quick manual 1 CD Utility 1 SATA cable 2 Console Cable(RJ45) 1 USA or Europe or Japan or UK power cord 1 Rack bracket 2 Screw for bracket (for Rack + HDD bracket) 1 Power cord hook 1 Box Packing 1 1.
1.
(1) Back Panel Power Inlet (2) System Configuration 1 2 9 3 4 5 6 10 7 8 10
Item Description Quantity 1 TOP COVER 1 2 POWER SUPPLY 1 3 BOTTOM BASE 1 4 POWER BRACKET 1 5 1U EAR BRACKET 2 6 HDD BRACKET 1 7 MEMBRANE 1 8 AMB-IH61N1/A/B 1 9 CPU Heatsink module 1 10 FAN 3 11
Chapter 2 Procedures of Assembly/Disassembly 2.1 2.5” HDD Installation The following instructions will guide you to install 2.5” HDD step-by-step. 1. Unfasten 2 screws of chassis top cover and take off it. 2. Release HDD bracket by unfastening 4 screws.
3. Take out HDD screws from packing bag. 4. Fix HDD with HDD bracket by 4 screws.
5. Fix HDD with HDD bracket by 4 screws.
6. Plug SATA power cable into motherboard. 7. The SATA power cable MUST go through below M/B power cable, please follow below photo.
8. Connect SATA cable and SATA power cable with HDD module. 9. Assemble top cover back by fastening the 2 screws.
2.2 CF Card Installation 1. Open the top cover (the same as above steps). 2. Push CF card into CF socket. 3. Finish the CF card installation.
2.3 Power Cord Hook Installation 1. Take out the hook from packing bag. 2. Install the hook from right side firstly. 3. Then install the hook by left side.
2.4 Rack Bracket Installation 1. Take out the screws and Rack bracket from packing bag. 2. Fixed the Rack bracket to Chassis by fastening 6 screws.
Board Guide 20
Chapter 3 Board Introduction AMB-IH61N1 is designed for rack-mounted platform for networking appliance, e.g. VPN, SSL, UTM or firewall. With 3rd Generation Intel Core i7/i5/i3 Processors / Pentium CPU, It is a powerful platform to satisfy different applications. By eight 10/100/1000Mbps LANs, the AMB-IH61N1 is sufficient for the small to middle size business security solution. AMB-IH61N1 can install 2 x HDD,BIOS and Jumper can control LAN bypass feature.
3.2 Package Contents Check if the following items are included in the package.
3.
Chapter 4 H/W Information This chapter describes the installation of AMB-IH61N1/A/B. At first, it shows the Function diagram and the layout of AMB-IH61N1/A/B. It then describes the unpacking information which you should read carefully, as well as the jumper/switch settings for the AMB-IH61N1/A/B configuration. 4.
4.
4.3 Connector pin define 4.1.1. DDR3 DIMM Connector DIMM1 DIMM2 Standard DDR3 DIMM connector 4.1.2. SATA connector SATA1 SATA2 Standard SATA connector 4.1.3. FAN Connector SYSFAN3 SYSFAN2 SYSFAN1 PIN Signal 1 2 GND +12V FAN Speed Detect 3 3 Pin, Pitch:2.
CPUFAN1 PIN Signal 1 2 GND +12V FAN Speed Detect FAN PWM Control 3 4 4 Pin, Pitch:2.54mm 4.1.4.
CN_2USB1 Standard USB 3.0 Type-A connector LED3 COM1 Green1: Power ON LED. RS-232, RJ45 connector Green2: HDD LED PIN Yellow1: LAN3&LAN4 Bypass 1 2 3 4 LED. Yellow2: LAN1&LAN2 Bypass LED. RST1 Signal PIN Signal RTS 5 6 7 8 GND DTR SOUT GND LED2 UP : Green1: Link LED Yellow1: Active LED Push this button to reset the Down : system. Green2: Link LED Yellow2: Active LED CN3, CN4 LED1 Dual SFP Connector.
4.1.5. CF Socket CF1 4.1.6.
4.1.7. Other Connector (For LAN1/LAN2 Bypass Function Select.). JP2 PIN Function 1-2 Forced Normal (Default) 2-3 Controlled By CPLD Open Forced Bypass For CPLD Firmware Update CPLD1 PIN 1 3 5 7 JP4 (For LAN3/LAN4 Bypass Function Select.). PIN LCM1 Function 2-3 Controlled By CPLD Ope Forced Bypass n LPC1 CMOS Backup Battery:.
SPI1 SPI BIOS firmware Update Header PIN 1 3 5 7 9 CCMOS1 Signal CS0 MISO WP# GND NC PIN Signal 2 VCC3 4 HOLD# 6 SPICLK 8 MOSI 10 NC CMOS Memory Clearing Header Extended Models Information Model Name Model Parts Difference Remark AMB-IH61N1 Intel GbE LAN x6 AMB-IH61N1A Intel GbE LAN x6 + 2 Fiber CN3 AMB-IH61N1B Intel GbE LAN x6 + 4 Fiber CN3 31 CN4
Chapter 5 BIOS Settings This chapter describes the BIOS menu displays and explains how to perform common tasks needed to get the system up and running. It also gives detailed explanation of the elements found in each of the BIOS menus.
5.1. Main Setup Once you enter the AMI BOS™ CMOS Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to highlight the item and then use the <+> <-> keys to select the value you want in each item. Note: Listed at the bottom of the menu are the control keys. If you need any help with the item fields, you can press the key, and it will display the relevant information.
5.2. Advanced Setup Option Choice SATA Configuration N/A SATA Device Options Settings N/A System Super IO Chip Parameters.
5.2.1. SATA Mode Selection Option SATA Mode Selection Choice IDE / AHCI Description Determines how SATA controller(s) operate.
5.2.2.
5.2.2.1. COM1 Configuration Option Choice Description Auto IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3,4,5,6,7,10,11,1 2 / IO=2F8h; Change Settings IRQ=3,4,5,6,7,10,11,1 2 / IO=3E8h; Select an optimal setting for Super IO device.
5.2.2.2.
Option Choice Serial Port Disabled / Enabled Description Enable or Disable Serial Port (COM) Auto IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3,4,5,6,7,10,11,1 2 / IO=2F8h; Change Settings IRQ=3,4,5,6,7,10,11,1 2 / IO=3E8h; Select an optimal setting for Super IO device. IRQ=3,4,5,6,7,10,11,1 2 / IO=2E8h; IRQ=3,4,5,6,7,10,11,1 2 Standard Serial Port Mode / IrDA Active pulse 1.
5.2.3. Serial Port Console Redirection Option Choice Console Redirection Disabled / Enabled Console Redirection Settings EMS Description Console Redirection Enable or Disable. The settings specify how the host computer and the remote N/A computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.
5.2.4. Intel(R) 82576 Gigabit Dual Port Network Connection Option Choice NIC Configuration N/A Click to configure the network device port. N/A Blink LEDs for the specified duration (up to 15 seconds).
5.2.5. Intel(R) 82574L Gigabit Network Connection Option Choice NIC Configuration N/A Click to configure the network device port. N/A Blink LEDs for the specified duration (up to 15 seconds).
5.3.
5.4. Chipset Setup Option Choice LAN 1 ~ 6 Disabled / Enabled Description Control the LAN Port Enable / Disable Control the USB EHCI (USB 2.0) EHCI1 N/A functions. One EHCI controller must always be enabled.
5.4.1. USB Configuration Option Choice EHCI1 Disabled / Enabled Description Control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enable.
5.5. Boot Setup Option Setup Prompt Timeout Boot up NumLock State Choice N/A ON / OFF Description Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.
5.6. Security Setup option dministrator Password HDD module name Choice N/A N/A Description Set Administrator Password Set HDD Password (It will show the HDD model, if you have to join the HDD.
5.6.1. HDD Password Description option Choice Set HDD Password N/A Description Set HDD User Password.
5.7. Save & Exit Setup option Choice Description Pressing on Save Changes and Exit this item for save Exit system setup after saving the changes. changes and exit. Discard Changes and Exit Pressing on this item for discard Exit system setup without saving any changes. changes and exit.
Pressing on this item for Save Changes confirmation : Save Save Changes done so far to any of the setup options.. configuration Pressing on this item for Discard Changes confirmation: Load Discard Changes done so far to any of the setup options. Previous Values Pressing on this item for Restore Defaults confirmation: Load Optimized Defaults Restore/Load Default values for all the setup options.
Chapter 6 Driver And Utility Installation 6.1. Driver CD Interface Introduction Acrosser provides the a driver CD, which includes the drivers, utilities, applications and documents. For Windows environment, it can be guided by the setup program; for Linux environment, the related files can be found at folder “IH61N1\Linux”. Once putting the CD into the optical disk drive, it will run automatically. The driver CD will also detect the MB information to see if they are matched.
6.1.1 Driver Page This is the Driver Installation Page.
Click the icon, all the drivers will be selected.
Click the icon, all selected items will be cleared.
Click the icon to install the selected drivers. The progress bar shows up. The main window will temporarily disappear.
Please click ‘Yes’ to restart the system.
Click this icon to browse this CD content.
6.1.2 Utility Page Note: For Testing utility running completely, it should be run at test-signed kernel-mode under Operating System x64 edition. “BCDEdit /set testsigning on” is the introduction to run at command mode which turns test-signed kernel-mode to on. Please refer to MSDN by following URL for more detail. http://msdn.microsoft.com/en-us/library/windows/hardware/ff542202(v=vs.85).
LAN Bypass APIs Test Utility LCM Test Utility 59
Watch Dog Test Utility Sample code 60
6.1.
. 6.1.4 Documents Page Double click on one of the items to open the manual.
Chapter 7 Software Installation and Programming Guide 7.1. Introduction 7.1.1 LCD Control Module The LCM (short for LCD Control Module) APIs provide interfaces to control the module. By invoking these APIs, programmers can implement the applications which have the functions listed below: 1. 2. 3. 4. 5. 6. Clear LCD screen. Turn on or off the cursor on the screen. Move the cursor on the screen. Turn on or off the text on the screen. Get the identification of the pressed key of the LCM.
7.1.4 IH61N Library (Window platform only) The released code for Windows platform includes a folder called ‘AMB-IH61N1’. In this folder, there are header files and source codes of all the APIs of LCM module, Watchdog, and LAN Bypass functions. The source codes in this folder generate the API library ‘IH61N.lib’ and ‘IH61N.dll’. Users who want to invoke the APIs can include the ‘IH61N.h’ in their application source code and compile their application with the library ‘IH61N.lib’ or ‘IH61N.dll’.
7.2.2 Watchdog On Linux platform: 1. Libw83627.h This file includes the declarations of the APIs and macro definitions. 2. maintest.c The source code of the utility. On Windows platform: 1. IH61N.h The header file of the APIs. 2. IH61N.lib and IH61N.dll The API libiaries. 7.2.3 LAN Bypass Subsystem On Linux platform: 1. bypass.h This file includes the declarations of the APIs and macro definitions. 2. main.c The source code of the utility. On Windows platform: 1. IH61N.h The header file of the APIs. 2.
7.3. API List and Descriptions 7.3.1 Type Definitions Typedef Typedef Typedef Typedef Typedef Typedef char unsigned char short unsigned short unsigned long int i8; u8; i16; u16; u32; i32; 7.3.2 LCD Control Module 1. i32 clrscrLcm( void ) Description: Clear the screen of the LCM. Return value: 0 after the screen is cleared. 2. i32 cursorLcm( bool mode ) Description: According to the argument ‘mode’, show the cursor on the LCM screen or eliminate the cursor on the LCM screen.
4. i32 displayLcm( bool mode ) Description: Show the text on the LCM screen or eliminate the text on the LCM screen. The content of the text is not altered. mode = true, show the text. mode = false, eliminate the text. Return value: 0 after the text has been shown or eliminated. 5. i32 getKeyLcm( void ) Description: Scan the LCM and return the identification of the pressed direction key. Return value: ‘UP’ if the ‘up’ direction key is pressed. ‘RIGHT’ if the ‘right’ direction key is pressed.
7.3.3 Watchdog 1. Syntax: Void wdt_start(int, int) Description: This function read the value of the watchdog time counter and return it to the caller. Parameters: None. Return Value: This function return the value of the time counter and return it to the caller as an unsigned integer. 2. Syntax: Void wdt_stop(void) Description: close watch dog timer. Parameters: None. Return Value: None. 3. Syntax: Int get_wdt_count(void) Description: This function get WDT_Counter. Parameters: None. Return Value: None. 7.
5. void forceBypass(void) Force the port to become bypass state. 6. void setWdt4(void) Set the watchdog timer to 4 seconds. 7. void setWdt8(void) Set the watchdog timer to 8 seconds. 8. void setWdt16(void) Set the watchdog timer to 16 seconds. 9. void setWdt32(void) Set the watchdog timer to 32 seconds.
FAQ There are 2 kinds of SATA modes --- AHCI & legacy IDE mode. When you use the Linux, We strongly suggest to use AHCI mode. For legacy IDE mode, we found some SATA HDD could have compatibility issue. Please confirm the BIOS setting is correct, thank you. Does my system support Windows 8? The system is designed and verified with Windows 7, Fedora 14 and Ubuntu 10. But, we did not verify this system with Windows 8. Please check with Acrosser local sales rep.
(reference only) Ensure the Network Connections/Local Area Connection is enabled (right click and choose “Enable”). If the problem persists, please turn off firewall and anti-virus S/W. If the problem still exists, please contact local FAE or service center for tests. (reference only) If the Network Connections/Local Area Connection is showed “limited connection” (yellow exclamation mark), please disable and enable your connection to fix this problem.
Appendix: Technical Support Form We deeply appreciate you purchase Acrosser products. Please find “tech_form.doc” file in our utility CD. If you have any questions or problems about Acrosser products, please fill in the following information: We will answer your questions a.s.a.p. 1) Describe your info and system info A. Your company name: _____________ B. Your contact info: _________________ & phone number: _________________ C. Your e-mail address: ______________________ D.
Acrosser Headquarters 新北市三重區重新路五段609巷12號10樓 10F., No.12, Lane 609, Sec. 5, Chongsin Rd., Sanchong District, New Taipei City 241, Taiwan, R.O.C. TEL: +886-(0)2-2 9999 000 FAX: +886-(0)2-2999-2887 acrosserinfo@acrosser.com Acrosser Taichung Office 台中市南屯區河南路四段162號12樓之6 12-6, No.162, Sec. 4, Henan Rd., Nantun Dist., Taichung City 408, Taiwan R.O.C.
