AND-D525N2 System User Manual 1
Copyright All Rights Reserved. Manual’s first edition: For the purpose of improving reliability, design and function, the information in this document is subject to change without prior notice and does not represent a commitment on the part of the manufacturer. The manufacturer shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Table of Contents Chapter 1 Introduction ......................................................................... 4 1.1. Specifications ............................................................................................................4 1.2. 1.3. Package Contents ......................................................................................................5 System Dissection .....................................................................................................
Chapter 1 Introduction AND-D525N2 with Intel Atom D525 processor is a networking microbox, which is a small, cost-effective and entry level solution. By four 10/100/1000Mbps LANs, the AND-D525N2 is sufficient for the small business security hardware solution. 1.1. Specifications CPU Intel Atom D525 Dual-core, clock speed 1.8G，TDP 13W Chipset Intel ICH8M，TDP 2.
1.2. Package Contents Check if the following items are included in the package.
1.3.
Chapter 2 Procedure of Assembly/Disassembly 2.1 HDD Installation The following instructions will guide you to install 2.5” HDD step-by-step. Unfasten 2 screws of chassis top cover and take off it. Fix HDD with HDD bracket by 4 screws.
Plug SATA cable into SATA2 connector and SATA power cable into motherboard.
Connect SATA cable and SATA power cable with HDD module. Assemble top cover back by fastening the 2 screws.
2.2 CF Card Installation Open the top cover (the same as above steps). Push CF card into CF socket. (It does not support PIO mode.
2.3 Installing SO-DIMM DRAM Open the top cover (the same as above steps). Install the SO-DIMM in the chassis.
2.4 Mini-PCIe Module Installation Open the top cover (the same as above steps). Install the mini-PCIe module in the chassis. 1) Insert the mini-PCIe module into the connector. 2) Push down the mini-PCIe module. 3) Fix it via screw.
2.5 Rack Bracket Installation Take out the screws and optional rack mount bracket from packing bag. Then, fix the optional rack mount bracket to chassis by fastening 6 screws. AND-D525N2 system will fit and install into 19” chassis.
Chapter 3 H/W Information This chapter describes the installation of AMB-D525N2. At first, it shows the Function diagram and the layout of AMB-D525N2. It then describes the unpacking information which you should read carefully, as well as the jumper/switch settings for the AMB-D525N2 configuration. 3.1. Mainboard illustration CPU Intel ATOM D525 CPU DIMM1 204-Pin DDR3 SO-DIMM Socket CF1 CF card Socket Chipset Intel ICH8M chipset MINIPCIE1 Mini PCI-Express Slot Note: CF1 does not support PIO mode.
3.2. Headers and Jumper Settings ATX2 LAN_LED2 LAN 2 LED header R_USB1* USB connector LAN_LED1 LAN 1 LED header COM1 RJ45 COM connector JP7 CF Card power supply control jumper RJ45_J1 RJ45 LAN1 connector JP8 CF Card Working Mode Selecting Jumper RJ45_J2 RJ45 LAN2 connector Front panel 1 header P_SATA1~2 SATA1~2 power supply connector. RJ45_J3 RJ45 LAN3 connector PW_LED1 CLR_CMOS1 Power LED header. Clear CMOS header. RJ45_J4 RJ45 LAN4 connector HD_LED1 HDD LED header.
2. CPU Fan Connector (3*1 Pin 2.54 mm) Location Header Pin Definition Pin Definition 1 GND 2 + 12V 3 FAN IO CPU_FAN1 3. System Fan Connector (3*1 Pin 2.54 mm) Location Header Pin Definition Pin Definition 1 GND 2 + 12V 3 + 5V SYS_FAN1 4. Front Panel2 Header (3*1 Pin 2.54mm) Location Connector F_PANEL2 Pin Definition Pin Definition 1 N/C 2 PWR_SW+ 3 PWR_SW- 5. Front Panel1 Header (3*1 Pin 2.
8~11. LAN LED Headers (2*1 Pin 2.54mm) Location Connector LAN_LED (1、2、3、4) Pin Definition Pin Definition 1 LAN_ACT+ 2 LAN_ACT- 12. CF Card Power Supply Control Jumper (3*1 Pin 2.54mm) Location Jumper JP7 Setting Function 1-2 5V Power Supply 2-3(Default) 3.3V Power Supply 13. CF Card Working Mode Selecting Jumper (3*1 Pin 2.54mm) Location Jumper JP8 Setting Function 1-2(Default) IDE Master 2-3 IDE Slave 14. SATA1~2 Power Supply Connector (4*1 Pin 2.
25. VGA Expansion Header (12*1 Pin 2.
Chapter 4 BIOS Settings This chapter describes the BIOS menu displays and explains how to perform common tasks needed to get the system up and running. It also gives detailed explanation of the elements found in each of the BIOS menus.
4.1. Main Setup Once you enter the Setup Utility, the Main menu will appear on the screen. Use the arrow and Enter keys to highlight the item and then use the < + > < - > keys to select the value you want in each item. Note: Listed at the bottom of the menu are the control keys. If you need any help with the item fields, you can press the key, and it will display the relevant information. Option Choice Description System Time N/A Set the time.
IDE Primary/Master N/A This item displays the IDE disk driver info IDE Primary/Slave N/A This item displays the IDE disk driver info SATA Port 1~2 N/A This item displays the SATA disk driver info Installed Memory N/A This item displays the motherboard memory size Available to OS N/A This item displays the available memory size to OS Used by devices N/A This item display the used memory size BIOS N/A This item display the BIOS version 21
4.1.1 IDE Primary/Master and Primary/Slave Setup Note: We suggest to remain the default “Auto” setting. System will auto detect the installed IDE device driver. Unless you are familiar with IDE device driver, please don’t change the settings.
4.1.2 SATA Port 1~2 Setup Note: We suggest to remain the default “Auto” setting. System will auto detect the installed SATA device driver. Unless you are familiar with SATA device driver, please don’t change the settings.
4.2. Advanced Setup Option CPU Control Choice Description N/A This item contains CPU parameters. N/A This item contains internal video configuration parameters. N/A This item contains ICH parameters. N/A This item contains LPC I/O devices parameters. Boot Feature N/A Select boot features. Console Redirection N/A This item contains console parameters.
4.2.1. CPU Control Sub-Menu Setup Option Choice Hyperthreading Enabled, Disabled Description Enable/Disable support of CPU hyperthreading.
4.2.2. Video (Intel IGD) Control Sub-Menu Setup Option Choice DVMT 4.
4.2.3.
Option PCI Express Sub-Menu ICH USB Sub-Menu Choice Description N/A Set PCI Express parameters N/A Set USB parameters 28
4.2.3.1. PCI Express Control Sub-Menu Setup Option Choice Description PCI Express Auto, Disabled, Set PCI Express Port 1 auto/enabled/disabled. If Port 1 is Root Port 1 Enabled PCI Express Auto, Disabled, Root Port 2~4 Enabled Root Port SAPM Support Auto, Disabled disabled, Port 2~4 will be disabled. Set PCI Express Port 2~4 auto/enabled/disabled. This item define ASPM parameter.
4.2.3.2.
4.2.4. LPC Control Sub-Menu Setup Option COM 1 Choice Auto, Enabled Disabled Description This item set COM 1 enabled/disabled/auto. 3F8/IRQ 4 I/O address, IRQ 2F8/IRQ 3 3E8/IRQ 4 Set COM 1 I/O address and IRQ.
4.2.5. Boot Features Setup Option Choice Description Summary Screen Disabled, Enabled Display system configuration on boot. QuickBoot Mode Disabled, Enabled Disable/Enable the system to skip some tests while booting.
4.2.6. Console Redirection Setup Option Com Port Address Baud Rate Flow Control Control connection Continue C.R. after POST # of video pages Choice Disabled, On-board COM A rates None, XON/XOFF, CTS/RTS Direct, Modem On, Off 1~8 Description Enable/Disable on-board COM port A. Set COM port baud rate, e.g. 9600, 19200 or 38400 Set COM port flow control Indicate COM port is connected to system or modem.
4.3.
4.4. Power Setup Option Choice Power Button On/Off, Behavior Wake/Sleep Description Select the system power state after press power button. Stay Off, After Power Failure Last State, Set the operation mode if power loss occurs.
4.5.
4.6. Exit Setup Option Exit Choice Description Yes, No Save configure change and reset the system. Yes, No Without save any changes and reset the system. Load Setup Default Yes, No Load default configuration. Discard Changes Yes, No Discard changes done so far to any of the setup options.
Save Changes Yes, No Save configuration changes.
