Server for Linux
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Echo Server installation and startup
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Working from a rescue CD
- 3.5 Working from a remote terminal
- 3.6 Backing up software and hardware RAID arrays
- 3.7 Support for LVM volumes
- 3.8 Backing up to tape drive
- Chapter 4. The program interface under X Window System
- Chapter 5. Creating backup archives
- Chapter 6. Restoring the backup data under X Window system
- 6.1 Considerations before recovery
- 6.2 Restoring files and folders from file archives
- 6.3 Restoring disks/partitions or files from images
- 6.3.1 Starting the Restore Data Wizard
- 6.3.2 Archive selection
- 6.3.3 Restoration type selection
- 6.3.4 Selecting a disk/partition to restore
- 6.3.5 Selecting a target disk/partition
- 6.3.6 Changing the restored partition type
- 6.3.7 Changing the restored partition file system
- 6.3.8 Changing the restored partition size and location
- 6.3.9 Restoring several disks or partitions at once
- 6.3.10 Setting restore options
- 6.3.11 Restoration summary and executing restoration
- 6.4 Restoring data with a rescue CD
- 6.5 Setting restore options
- Chapter 7. Scheduling tasks
- Chapter 8. Managing Acronis Secure Zone
- Chapter 9. Creating bootable media
- Chapter 10. Operations with archives
- Chapter 11. Notifications and event tracing
- Chapter 12. Console mode
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
5. Select whether you want to mount image in Read-only or Read/Write mode.
6. If you select Read/Write mode, the program assumes that the connected image will
be modified, and creates an incremental archive file to capture the changes. It is strongly
recommended that you list the forthcoming changes in the comment to this file.
7. The program displays a summary containing a single operation. Click Proceed to
mount the selected partition image.
8. After the image is mounted, you can operate with files or folders as if they were
located on a real disk.
You can mount multiple partition images. If you want to mount another partition image,
repeat the procedure.
10.2.2 Unmounting an image
We recommend that you unmount the virtual disk after all necessary operations are
finished, as keeping up virtual disks takes considerable system resources. If you do not,
the virtual disk will disappear after your server is turned off.
To disconnect the virtual disk, click Unmount Image and select the folder to unmount.
10.3 Consolidating backups
The file name-based consolidation allows deleting from any archive the backups that you
do not need any more while keeping the archive consistency. You can delete from an
archive, if need be, the base full backup. The program will create another full backup in
place of the oldest remaining backup.
To consolidate backups in the archive:
1. Start the Backup Consolidation Wizard by selecting Tools -> Consolidate
archive in the main program menu.
2. Select the archive from the drives tree. The file name-based consolidation does not
support Acronis Secure Zone, so it is not displayed in the tree.
An archive MyBackup consisting of one full and four incremental backups is selected