Server for Linux
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Echo Server installation and startup
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Working from a rescue CD
- 3.5 Working from a remote terminal
- 3.6 Backing up software and hardware RAID arrays
- 3.7 Support for LVM volumes
- 3.8 Backing up to tape drive
- Chapter 4. The program interface under X Window System
- Chapter 5. Creating backup archives
- Chapter 6. Restoring the backup data under X Window system
- 6.1 Considerations before recovery
- 6.2 Restoring files and folders from file archives
- 6.3 Restoring disks/partitions or files from images
- 6.3.1 Starting the Restore Data Wizard
- 6.3.2 Archive selection
- 6.3.3 Restoration type selection
- 6.3.4 Selecting a disk/partition to restore
- 6.3.5 Selecting a target disk/partition
- 6.3.6 Changing the restored partition type
- 6.3.7 Changing the restored partition file system
- 6.3.8 Changing the restored partition size and location
- 6.3.9 Restoring several disks or partitions at once
- 6.3.10 Setting restore options
- 6.3.11 Restoration summary and executing restoration
- 6.4 Restoring data with a rescue CD
- 6.5 Setting restore options
- Chapter 7. Scheduling tasks
- Chapter 8. Managing Acronis Secure Zone
- Chapter 9. Creating bootable media
- Chapter 10. Operations with archives
- Chapter 11. Notifications and event tracing
- Chapter 12. Console mode
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
If the archive is located on removable media, e.g. CD, first insert the last CD and then
insert disks in reverse order when Restore Data Wizard prompts.
Data recovery directly from an FTP server requires the archive to be split into files no
more than 2GB in size. If you suspect that some of the files may be larger, first copy the
entire archive (along with the initial full backup) to a local hard disk or network share
disk. See notes and recommendations for supporting FTP server in
1.4.2 Supported
storage media
.
If you added a comment to the archive, it will be displayed to the right of the drives tree.
If the archive was protected with a password, Acronis True Image Echo Server will ask for
it. The partitions layout, the comment and the Next button will be unavailable until you
enter the correct password.
2. If the selected archive contains incremental backups, Acronis True Image Echo Server
will suggest that you select one of successive incremental backups by its creation
date/time. Thus, you can return the disk data to a certain moment.
To restore data from an incremental backup, you must have all previous incremental
backups and the initial full backup. If any of successive backups is missing, restoration is
not possible.
To restore data from a differential backup, you must have the initial full backup as well.
6.3.3 Restoration type selection
Select what you want to restore:
Restore specified files or folders
With this selection, you will be further offered to select where to restore selected
folders/files (original or new location), choose files/folders to be restored and so on.
These steps look like those in file archive restore. However, watch your selection: if you
are to restore files instead of disk/partition, uncheck the unnecessary folders. Otherwise
you will restore a lot of excessive files. Then you will be taken directly to Restoration
Summary screen (
6.3.11 Restoration summary and executing restoration)