User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Workstation installation and
- Chapter 3. General information and proprietary Acronis tech
- 3.1 The difference between file archives and disk/partition
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape drive
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Workstation (local vers
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Compression level
- 6.3.5 Backup performance
- 6.3.6 Fast incremental/differential backup
- 6.3.7 Archive splitting
- 6.3.8 File-level security settings
- 6.3.9 Media components
- 6.3.10 Additional settings
- 3.7.1 How to use
- 3.7.2 Using Acronis Universal Restore in virtual environmen
- 3.7.3 Hints on using Acronis Universal Restore
- 3.7.4 Benefits
- Chapter 7. Restoring the backup data
- 7.1 Restore under Windows or boot from CD?
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several partitions at once
- 7.3.11 Setting restore options
- 7.3.12 Using Acronis Universal Restore
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- Chapter 8. Scheduling tasks
- Chapter 9. Managing Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Other operations
- Chapter 12. Mounting an image as a virtual drive
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 13.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
- Chapter 15. Command-line mode and scripting
Chapter 11. Other operations
11.1 Validating backup archives
To be certain that your archives are not damaged, you can check their integrity.
1. To invoke the Backup Archive Validation Wizard, select Validate Backup Archive in
the main window or in the Tools group or click Validate Backup Archive on the toolbar.
2. Click Next.
3. Select the archive to validate. If the archive is located in Acronis Secure Zone, select it to
choose the archive on the next step.
4. Click Next.
5. Clicking Proceed will launch the validation procedure. After the validation is complete,
you will see the results window. You can cancel checking by clicking Cancel.
To check data from an archive, containing incremental backups, you must have all
incremental backup files and the initial full backup. If any of successive backups is missing in
the archive, the validation is impossible.
To check data from a differential backup, you must have the initial full backup as well.
However, if you created several differential or both incremental and differential backups
based on the same full backup (and therefore, in the same folder), you will need ALL of
these successive backups to validate the archive.
11.2 Operation results notification
Sometimes a backup or restore procedure can last for 30 minutes or more. Acronis True
Image Workstation can notify you when it is finished using the WinPopup service or via e-
mail. The program can also duplicate messages issued during the operation or send you the
full operation log after operation completion.
By default all notifications are disabled.
Copyright © Acronis, Inc., 2000-2006 83