User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Workstation installation and
- Chapter 3. General information and proprietary Acronis tech
- 3.1 The difference between file archives and disk/partition
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape drive
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Workstation (local vers
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Compression level
- 6.3.5 Backup performance
- 6.3.6 Fast incremental/differential backup
- 6.3.7 Archive splitting
- 6.3.8 File-level security settings
- 6.3.9 Media components
- 6.3.10 Additional settings
- 3.7.1 How to use
- 3.7.2 Using Acronis Universal Restore in virtual environmen
- 3.7.3 Hints on using Acronis Universal Restore
- 3.7.4 Benefits
- Chapter 7. Restoring the backup data
- 7.1 Restore under Windows or boot from CD?
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several partitions at once
- 7.3.11 Setting restore options
- 7.3.12 Using Acronis Universal Restore
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- Chapter 8. Scheduling tasks
- Chapter 9. Managing Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Other operations
- Chapter 12. Mounting an image as a virtual drive
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 13.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
- Chapter 15. Command-line mode and scripting
Chapter 10. Creating bootable media
You can run Acronis True Image Workstation on a bare metal or on a crashed computer that
cannot boot. You can also back up disks on a non-Windows computer, copying all its data
sector-by-sector into the backup archive. To do so, you will need bootable media with the
standalone Acronis True Image Workstation version.
If you purchased the boxed product, you already have such a bootable CD, because the
installation CD contains, besides the program installation files, the Acronis True Image
Workstation standalone bootable version.
If you purchased Acronis True Image Workstation on the Web, you can create bootable
media using the Bootable Media Builder. For this, you will need a CD-R/RW blank, several
formatted diskettes (the wizard will tell you the exact number), or any other media your
workstation can boot from, such as a Zip drive.
Acronis True Image Workstation also provides the ability to create an ISO image of a
bootable disk on the hard disk. If there is a Microsoft RIS server in your local network, an IT
administrator can save the bootable data on this server as well. Then any networked
computer will be able to boot any program from the RIS package.
If you have other Acronis products, such as Acronis Disk Director Suite, installed on your
computer, you can include standalone versions of these programs on the same bootable disk
as well.
This feature is available both in Acronis True Image Workstation local version and Acronis
True Image Management Console. However, Acronis True Image Management Console does
not contain Rescue Media Builder in its own installation. Therefore, to be able to create
bootable media/RIS package from Acronis True Image Management Console, you must have
Acronis True Image Workstation or another Acronis product including Rescue Media Builder,
installed on the same computer.
If you have chosen not to install the Bootable Media Builder during Acronis True Image
Workstation installation, you will not be able to use this feature.
1. Click Create Bootable Rescue Media on the toolbar or the sidebar, or select Create
Bootable Rescue Media from the Tools menu. You can also run the Bootable Rescue
Media Builder without loading Acronis True Image Workstation by selecting Programs ->
Acronis -> True Image -> Bootable Rescue Media Builder from the Start menu.
2. Select which components of Acronis programs you want to place on the bootable media.
80 Copyright © Acronis, Inc., 2000-2006