User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Workstation installation and
- Chapter 3. General information and proprietary Acronis tech
- 3.1 The difference between file archives and disk/partition
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape drive
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Workstation (local vers
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Compression level
- 6.3.5 Backup performance
- 6.3.6 Fast incremental/differential backup
- 6.3.7 Archive splitting
- 6.3.8 File-level security settings
- 6.3.9 Media components
- 6.3.10 Additional settings
- 3.7.1 How to use
- 3.7.2 Using Acronis Universal Restore in virtual environmen
- 3.7.3 Hints on using Acronis Universal Restore
- 3.7.4 Benefits
- Chapter 7. Restoring the backup data
- 7.1 Restore under Windows or boot from CD?
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several partitions at once
- 7.3.11 Setting restore options
- 7.3.12 Using Acronis Universal Restore
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- Chapter 8. Scheduling tasks
- Chapter 9. Managing Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Other operations
- Chapter 12. Mounting an image as a virtual drive
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 13.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
- Chapter 15. Command-line mode and scripting
4. Click Next.
5. If you know which drivers will fit for the new hardware, add them to the drivers list in the
next window. You can add HAL and hard disk controller drivers. Drivers for devices (sound
cards, network adapters, video cards etc.) will be found by Windows itself when it boots.
Thus, Acronis Universal Restore uses three sources for drivers search: the driver repository,
the list of user-specified (enforced) drivers, and the Windows default driver storage folders
(in the image being restored). The program will find the most suitable drivers of all available
and install them into the restored system. However, the drivers, defined by the user
(enforced drivers), will have the priority. They will be installed, with appropriate warning,
even if the program finds the better driver.
When migrating from RAID to RAID, be sure to specify an appropriate driver for the RAID
controller in the Forcedly Installed Drivers window. Otherwise a basic HDD driver will be
installed.
When restoring the system to a virtual machine that uses SCSI hard drive controller, be sure
to specify SCSI drivers for virtual environment in the Forcedly Installed Drivers window.
Use drivers bundled with your virtual machine software or download the latest drivers
versions from the software manufacturer website.
6. Click Next.
7.3.13 Restoration summary and executing restoration
1. At the final step, the restoration summary is displayed. Up to this point, you can click
Back to make changes in the created task. If you click Cancel, no changes will be made to
disk(s). Clicking Proceed will launch the task execution.
2. (For Acronis True Image Workstation local version, or Acronis True Image Management
Console, connected to the target computer) The task will appear on the Active tasks pane
of the main window. The task progress will be shown in the special window.
You can stop the procedure by clicking Cancel. However, it is critical to note that the target
partition will be deleted and its space unallocated – the same result you will get if the
restoration is unsuccessful. To recover the “lost” partition, you will have to restore it from
the image again.
68 Copyright © Acronis, Inc., 2000-2006