User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Workstation installation and
- Chapter 3. General information and proprietary Acronis tech
- 3.1 The difference between file archives and disk/partition
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape drive
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Workstation (local vers
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Compression level
- 6.3.5 Backup performance
- 6.3.6 Fast incremental/differential backup
- 6.3.7 Archive splitting
- 6.3.8 File-level security settings
- 6.3.9 Media components
- 6.3.10 Additional settings
- 3.7.1 How to use
- 3.7.2 Using Acronis Universal Restore in virtual environmen
- 3.7.3 Hints on using Acronis Universal Restore
- 3.7.4 Benefits
- Chapter 7. Restoring the backup data
- 7.1 Restore under Windows or boot from CD?
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several partitions at once
- 7.3.11 Setting restore options
- 7.3.12 Using Acronis Universal Restore
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- Chapter 8. Scheduling tasks
- Chapter 9. Managing Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Other operations
- Chapter 12. Mounting an image as a virtual drive
- Chapter 13. Transferring the system to a new disk
- 13.1 General information
- 13.2 Security
- 13.3 Executing transfers
- 13.3.1 Selecting Clone mode
- 13.3.2 Selecting source disk
- 13.3.3 Selecting destination disk
- 13.3.4 Partitioned destination disk
- 13.3.5 Old and new disk partition layout
- 13.3.6 Old disk data
- 13.3.7 Destroying the old disk data
- 13.3.8 Selecting partition transfer method
- 13.3.9 Partitioning the old disk
- 13.3.10 Old and new disk partition layouts
- 13.3.11 Cloning summary
- 13.4 Cloning with manual partitioning
- Chapter 14. Adding a new hard disk
- Chapter 15. Command-line mode and scripting
2.3.2 Firewall setup
Acronis True Image Workstation uses the following ports and IP addresses for remote
operation:
• server (Acronis True Image Agent) UDP port: 9876
• server (Acronis True Image Agent) TCP port: 9876, if busy chose port at
random
• client (Acronis True Image Management Console) UDP port: 9877, if busy
chose port at random
• IPv4 multicast address: 239.255.219.45
• IPv6 multicast address: FF05::fAA5:741E.
You might have to set the appropriate firewall access options. Options for the Windows
Firewall, included in Windows XP Service Pack 2 and Windows 2003 Server, are set
automatically during Acronis True Image Workstation components installation. However,
make sure that the option File and Printer Sharing in the Control panel -> Windows
Firewall -> Exceptions is enabled on the remote computer, before the remote operation
starts.
2.4 Running Acronis True Image Workstation components
2.4.1. Running Acronis True Image Workstation (local version)
You can run Acronis True Image Workstation in Windows by selecting Start -> Programs -
> Acronis -> Acronis True Image Workstation -> Acronis True Image Workstation
or clicking on the appropriate shortcut on the desktop.
If your operating system does not load for some reason, you can run Acronis Startup
Recovery Manager. However, this must be activated prior to use; see
3.4 Acronis Startup
Recovery Manager
to learn more about this procedure. To run the program, press F11 during
workstation bootup, when you see a corresponding message that tells you to press that key.
Acronis True Image Workstation will be run in the standalone mode, allowing you to recover
the damaged partitions.
If your disk data is totally corrupted and you cannot boot (or if you have not activated
Acronis Startup Recovery Manager), load the standalone Acronis True Image Workstation
version from the bootable media (supplied with the retail box or created by you using
Rescue Media Builder) or RIS-server. Then you will be able to restore the disk from its
previously created image.
2.4.2 Running Acronis True Image Management Console
To run Acronis True Image Management Console, select Start -> Programs -> Acronis -
> Acronis True Image Management Console -> Acronis True Image Management
Console.
2.5 Removing Acronis True Image Workstation components
You can remove any Acronis True Image Workstation component separately by selecting
Control panel -> Add or remove programs -> <The component name> ->
Remove. Then follow instructions on the screen. You may have to reboot your computer
afterwards to complete the task.
14 Copyright © Acronis, Inc., 2000-2006