User Guide
Table Of Contents
- Chapter 1. Introduction
- Chapter 2. Acronis True Image Home installation and startin
- Chapter 3. General information and proprietary Acronis tech
- Chapter 4. Using Acronis True Image Home
- Chapter 5. Creating backup archives
- Chapter 6. Restoring the backup data
- 6.1 Restore under Windows or boot from CD?
- 6.2 Restoring files and folders from file archives
- 6.3 Restoring disks/partitions or files from images
- 6.3.1 Starting the Restore Data Wizard
- 6.3.2 Archive selection
- 6.3.3 Restoration type selection
- 6.3.4 Selecting a disk/partition to restore
- 6.3.5 Selecting a target disk/partition
- 6.3.6 Changing the restored partition type
- 6.3.7 Changing the restored partition file system
- 6.3.8 Changing the restored partition size and location
- 6.3.9 Assigning a letter to the restored partition
- 6.3.10 Restoring several disks or partitions at once
- 6.3.11 Setting restore options
- 6.3.12 Restoration summary and executing restoration
- 6.4 Setting restore options
- Chapter 7. Scheduling tasks
- Chapter 8. Managing Acronis Secure Zone
- Chapter 9. Creating bootable media
- Chapter 10. Other operations
- Chapter 11. Mounting an image as a virtual drive
- Chapter 12. Transferring the system to a new disk
- 12.1 General information
- 12.2 Security
- 12.3 Executing transfers
- 12.3.1 Selecting Clone mode
- 12.3.2 Selecting source disk
- 12.3.3 Selecting destination disk
- 12.3.4 Partitioned destination disk
- 12.3.5 Old and new disk partition layout
- 12.3.6 Old disk data
- 12.3.7 Destroying the old disk data
- 12.3.8 Selecting partition transfer method
- 12.3.9 Partitioning the old disk
- 12.3.10 Old and new disk partition layouts
- 12.3.11 Cloning summary
- 12.4 Cloning with manual partitioning
- Chapter 13. Adding a new hard disk
- Appendix A. Partitions and file systems
- Appendix B. Hard disks and BIOS setup
6.4.4 File-level security settings
The default setting – Restore files with their security settings.
If the files’ security settings were preserved during backup (see
5 3.7 File level secu ity
settings), you can choose whether to restore files’ security settings or let the files inherit the
security settings of the folder where they will be restored.
. - r
This option is effective only when restoring files from file/folders archives.
6.4.5 Additional settings
1. You can choose whether to restore files’ date and time from the archive or assign the files
the current date and time.
2. Before data is restored from the archive, Acronis True Image Home can check its integrity.
If you suspect that the archive might have been corrupted, select Validate backup
archive before restoration.
To check data from an archive containing incremental backups, you must have all
incremental backup files and the initial full backup. If any successive backups are missing
from the archive, validation is not possible.
To check data from a differential backup, you must have the initial full backup as well.
However, if you created several differential or both incremental and differential backups
based on the same full backup (and therefore, in the same folder), you will need ALL of
these successive backups to validate the archive.
3. Having restored a disk/partition from an image, Acronis True Image Home can check the
integrity of the file system. To do so, select Check file system after restoration.
Verification of the file system is available only when restoring disk/partitions under Windows
NT SP6/2000/XP and for FAT16/32 and NTFS file systems.
Copyright © Acronis, Inc., 2000-2006 41