Datasheet
Table Of Contents
- Chapter 1. Introduction
- 1.1 Acronis® True Image Echo Enterprise Server – a complete solution for corporate users
- 1.2 Acronis True Image Echo Enterprise Server components
- 1.3 New in Acronis True Image Echo Enterprise Server
- 1.4 Supported file systems and storage media
- 1.5 License policy
- 1.6 Technical support
- Chapter 2. Acronis True Image Echo Enterprise Server installation and startup
- 2.1 System requirements
- 2.2 Security parameters
- 2.3 Installing Acronis True Image Echo Enterprise Server components
- 2.3.1 Installation of Acronis True Image Echo Enterprise Server local version and Acronis True Image Agent for Windows
- 2.3.2 Installation of Acronis True Image Agent for Linux
- 2.3.3 Installation of Acronis Group Server
- 2.3.4 Acronis Backup Server installation and setup
- 2.3.5 Acronis Universal Restore installation
- 2.4 Extracting Acronis True Image Echo Enterprise Server components
- 2.5 Running Acronis True Image Echo Enterprise Server components
- 2.6 Removing Acronis True Image Echo Enterprise Server components
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape libraries and tape drives
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Echo Enterprise Server (local version)
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Database support
- 6.3.5 Compression level
- 6.3.6 Backup performance
- 6.3.7 Fast incremental/differential backup
- 6.3.8 Archive splitting
- 6.3.9 File-level security settings
- 6.3.10 Media components
- 6.3.11 Error handling
- 6.3.12 Dual destination backup
- 6.3.13 Wake On LAN
- 6.3.14 Additional settings
- Chapter 7. Restoring the backup data
- 7.1 Considerations before recovery
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several disks or partitions at once
- 7.3.11 Using Acronis Universal Restore
- 7.3.12 Setting restore options
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- 7.5 Creating dynamic disks and volumes
- Chapter 8. Scheduling tasks
- Chapter 9. Managing the Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Operations with archives
- Chapter 12. Notifications and event tracing
- Chapter 13. Working with a virtual environment
- Chapter 14. Transferring the system to a new disk
- 14.1 General information
- 14.2 Security
- 14.3 Executing transfers
- 14.3.1 Selecting Clone mode
- 14.3.2 Selecting source disk
- 14.3.3 Selecting destination disk
- 14.3.4 Partitioned destination disk
- 14.3.5 Old and new disk partition layout
- 14.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 14.3.8 Selecting partition transfer method
- 14.3.9 Partitioning the old disk
- 14.3.10 Old and new disk partition layouts
- 14.3.11 Cloning summary
- 14.4 Cloning with manual partitioning
- Chapter 15. Adding a new hard disk
- Chapter 16. Command-line mode and scripting
The backup process will run concurrently with your commands if you uncheck the Do not
perform operations until the commands execution is complete box, which is
checked by default.
7.4.4 Restoration priority
The default setting – Low.
The priority of any process running in a system determines the amount of CPU usage and
system resources allocated to that process. Decreasing the restoration priority will free
more resources for other CPU tasks. Increasing of restoration priority may speed up the
restore process due to taking resources from the other currently running processes. The
effect will depend on total CPU usage and other factors.
7.4.5 File-level security settings
The preset is Restore files with their security settings.
If the files’ security settings were preserved during backup (see
6.3.9 File-level security
settings
), you can choose whether to restore files’ security settings or let the files inherit
the security settings of the folder where they will be restored.
This option is effective only when restoring files from file/folders archives.
7.4.6 Specifying mass storage drivers
This option appears only in those computers’ options, where Acronis Universal Restore is
installed.
Acronis Universal Restore is an option to Acronis True Image Echo Enterprise Server. It
should be purchased separately and installed from a separate setup file. For more
information see
3.7 Acronis Universal Restore
.
Here you can specify a path to the driver repository on a network drive or CD where
Acronis Universal Restore will search for drivers at restoring a system disk on dissimilar
hardware. If several paths are specified, the program will scan all locations and choose
the most suitable driver.
90 Copyright © Acronis, Inc., 2000-2007