Datasheet
Table Of Contents
- Chapter 1. Introduction
- 1.1 Acronis® True Image Echo Enterprise Server – a complete solution for corporate users
- 1.2 Acronis True Image Echo Enterprise Server components
- 1.3 New in Acronis True Image Echo Enterprise Server
- 1.4 Supported file systems and storage media
- 1.5 License policy
- 1.6 Technical support
- Chapter 2. Acronis True Image Echo Enterprise Server installation and startup
- 2.1 System requirements
- 2.2 Security parameters
- 2.3 Installing Acronis True Image Echo Enterprise Server components
- 2.3.1 Installation of Acronis True Image Echo Enterprise Server local version and Acronis True Image Agent for Windows
- 2.3.2 Installation of Acronis True Image Agent for Linux
- 2.3.3 Installation of Acronis Group Server
- 2.3.4 Acronis Backup Server installation and setup
- 2.3.5 Acronis Universal Restore installation
- 2.4 Extracting Acronis True Image Echo Enterprise Server components
- 2.5 Running Acronis True Image Echo Enterprise Server components
- 2.6 Removing Acronis True Image Echo Enterprise Server components
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape libraries and tape drives
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Echo Enterprise Server (local version)
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Database support
- 6.3.5 Compression level
- 6.3.6 Backup performance
- 6.3.7 Fast incremental/differential backup
- 6.3.8 Archive splitting
- 6.3.9 File-level security settings
- 6.3.10 Media components
- 6.3.11 Error handling
- 6.3.12 Dual destination backup
- 6.3.13 Wake On LAN
- 6.3.14 Additional settings
- Chapter 7. Restoring the backup data
- 7.1 Considerations before recovery
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several disks or partitions at once
- 7.3.11 Using Acronis Universal Restore
- 7.3.12 Setting restore options
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- 7.5 Creating dynamic disks and volumes
- Chapter 8. Scheduling tasks
- Chapter 9. Managing the Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Operations with archives
- Chapter 12. Notifications and event tracing
- Chapter 13. Working with a virtual environment
- Chapter 14. Transferring the system to a new disk
- 14.1 General information
- 14.2 Security
- 14.3 Executing transfers
- 14.3.1 Selecting Clone mode
- 14.3.2 Selecting source disk
- 14.3.3 Selecting destination disk
- 14.3.4 Partitioned destination disk
- 14.3.5 Old and new disk partition layout
- 14.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 14.3.8 Selecting partition transfer method
- 14.3.9 Partitioning the old disk
- 14.3.10 Old and new disk partition layouts
- 14.3.11 Cloning summary
- 14.4 Cloning with manual partitioning
- Chapter 15. Adding a new hard disk
- Chapter 16. Command-line mode and scripting
2. Set the NIC properties on the computer as follows.
Control Panel -> System -> Device Manager -> Network adapters -> select the NIC ->
Properties -> Advanced:
Enable PME -> Enabled
Wake On Link Settings -> OS Controlled
Wake On Settings -> Wake On Magic Packet.
3. Find out the computer MAC address (Local Area Connection -> Status -> Support ->
Details -> Physical Address.)
4. Repeat steps 1-3 for all computers you wish to wake on LAN.
To enable the Wake On LAN option on the Acronis Group Server:
1. Find the computer to be backed up in the list of computers.
2. Select the computer and enter its MAC address in the Acronis Group Server (sidebar ->
Computer details -> MAC address: Set -> type the hex MAC address as XXXXXXXXXXXX
or XX-XX-XX-XX-XX -> click OK). The program will test the MAC address for validity and
display the test result.
3. Repeat steps 1-2 for all computers you wish to wake on LAN.
4. Schedule a group backup task for the above computers. When setting the backup
options, ensure that the Wake On LAN option is enabled. Any computer that is asleep as
the task starts will be powered on for running the task.
6.3.14 Additional settings
1. Validate backup archive upon operation completion
The preset is disabled.
The program will check integrity of the just created or supplemented archive immediately
after backup when enabled.
To check archive data integrity, you must have all incremental and differential backups
belonging to the archive and the initial full backup. If any of successive backups is
missing, validation is not possible.
2. Overwrite data on a tape without user confirmation
The preset is enabled.
A full backup, when created on a tape drive, overwrites all data stored on the tape (see
3.8.2 Backing up to tape drives
for more information). In this situation, Acronis True
Image Echo Enterprise Server will warn that you are about to lose data on the tape. To
disable this warning, check the middle box.
3. Ask for first media while creating backup archives on removable media
The preset is enabled.
You can choose whether to display the Insert First Media prompt when backing up to
removable media. With the default setting, backing up to removable media may be not
possible if the user is away, because the program will wait for someone to press OK in
the prompt box. Therefore, you should disable the prompt when scheduling a backup to
removable media. Then, if the removable media is available (for example, CD-R/RW
inserted), the task can run unattended.
Copyright © Acronis, Inc., 2000-2007 75