Datasheet
Table Of Contents
- Chapter 1. Introduction
- 1.1 Acronis® True Image Echo Enterprise Server – a complete solution for corporate users
- 1.2 Acronis True Image Echo Enterprise Server components
- 1.3 New in Acronis True Image Echo Enterprise Server
- 1.4 Supported file systems and storage media
- 1.5 License policy
- 1.6 Technical support
- Chapter 2. Acronis True Image Echo Enterprise Server installation and startup
- 2.1 System requirements
- 2.2 Security parameters
- 2.3 Installing Acronis True Image Echo Enterprise Server components
- 2.3.1 Installation of Acronis True Image Echo Enterprise Server local version and Acronis True Image Agent for Windows
- 2.3.2 Installation of Acronis True Image Agent for Linux
- 2.3.3 Installation of Acronis Group Server
- 2.3.4 Acronis Backup Server installation and setup
- 2.3.5 Acronis Universal Restore installation
- 2.4 Extracting Acronis True Image Echo Enterprise Server components
- 2.5 Running Acronis True Image Echo Enterprise Server components
- 2.6 Removing Acronis True Image Echo Enterprise Server components
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape libraries and tape drives
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Echo Enterprise Server (local version)
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Database support
- 6.3.5 Compression level
- 6.3.6 Backup performance
- 6.3.7 Fast incremental/differential backup
- 6.3.8 Archive splitting
- 6.3.9 File-level security settings
- 6.3.10 Media components
- 6.3.11 Error handling
- 6.3.12 Dual destination backup
- 6.3.13 Wake On LAN
- 6.3.14 Additional settings
- Chapter 7. Restoring the backup data
- 7.1 Considerations before recovery
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several disks or partitions at once
- 7.3.11 Using Acronis Universal Restore
- 7.3.12 Setting restore options
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- 7.5 Creating dynamic disks and volumes
- Chapter 8. Scheduling tasks
- Chapter 9. Managing the Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Operations with archives
- Chapter 12. Notifications and event tracing
- Chapter 13. Working with a virtual environment
- Chapter 14. Transferring the system to a new disk
- 14.1 General information
- 14.2 Security
- 14.3 Executing transfers
- 14.3.1 Selecting Clone mode
- 14.3.2 Selecting source disk
- 14.3.3 Selecting destination disk
- 14.3.4 Partitioned destination disk
- 14.3.5 Old and new disk partition layout
- 14.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 14.3.8 Selecting partition transfer method
- 14.3.9 Partitioning the old disk
- 14.3.10 Old and new disk partition layouts
- 14.3.11 Cloning summary
- 14.4 Cloning with manual partitioning
- Chapter 15. Adding a new hard disk
- Chapter 16. Command-line mode and scripting
Here’s an example of how you would use this feature. If failure occurs on a computer,
turn on the computer and press F11 when you see the "Press F11 for Acronis Startup
Recovery Manager" message. This will run a standalone version of Acronis True Image
Echo Enterprise Server that only slightly differs from the complete version. For
information on restoring damaged partitions, see
Chapter 7. Restoring the backup data
.
Be careful! Disk letters in standalone Acronis True Image Echo Enterprise Server might
sometimes differ from the way Windows identifies drives. For example, the D: drive
identified in the standalone Acronis True Image might correspond to the E: drive in
Windows.
3.5 Acronis Backup Server
Acronis Backup Server is an application for centralized storage and management of
enterprise backup archives in accordance with the policies, set by an administrator. It
ensures optimal usage of storage resources used for backup archives. Outdated archives
will be automatically deleted; at the same time, the latest data recovery is always
possible. In addition, Acronis Backup Server facilitates creation and executing group
backup tasks.
For information on how to install and set up Acronis Backup Server, see
2.3.4 Acronis
Backup Server installation and setup
. For information on how to manage Acronis Backup
Server, see
4.5 Managing backup server
.
3.5.1 Backup locations
Backup server is a networked computer where Acronis Backup Server is installed. A
backup location is a storage area for backups on a local backup server hard drive.
At installation, Acronis Backup Server creates one (default) backup location. The location
has the following properties:
Path: C:\Documents and Settings\All Users\Application Data\Acronis\BackupServer\
Backups
Maximum backup location size: Unlimited
Maximum storage period (days): Unlimited
All backup data destined to the backup server will be saved in the default backup location.
Because it may not be practical or efficient for you to store all backup data in one
location, the backup server allows you to create as many locations as you need, each with
its own properties. The three basic rules are:
• any location, except for the default one, must be assigned to at least one user or
computer
• only one location can be assigned to a user or computer
• the default location may not be assigned to a user or computer. There must be a
default backup location on a backup server though.
You can create a separate location for each user or computer while adding them to the
backup server, distribute the users/computers between several locations, or assign the
same location to all users/computers.
Maintaining multiple small backup locations on a single disk does not allow for tracking
changes in total disk space usage. At the same time, manual management of thousands
28 Copyright © Acronis, Inc., 2000-2007