Datasheet
Table Of Contents
- Chapter 1. Introduction
- 1.1 Acronis® True Image Echo Enterprise Server – a complete solution for corporate users
- 1.2 Acronis True Image Echo Enterprise Server components
- 1.3 New in Acronis True Image Echo Enterprise Server
- 1.4 Supported file systems and storage media
- 1.5 License policy
- 1.6 Technical support
- Chapter 2. Acronis True Image Echo Enterprise Server installation and startup
- 2.1 System requirements
- 2.2 Security parameters
- 2.3 Installing Acronis True Image Echo Enterprise Server components
- 2.3.1 Installation of Acronis True Image Echo Enterprise Server local version and Acronis True Image Agent for Windows
- 2.3.2 Installation of Acronis True Image Agent for Linux
- 2.3.3 Installation of Acronis Group Server
- 2.3.4 Acronis Backup Server installation and setup
- 2.3.5 Acronis Universal Restore installation
- 2.4 Extracting Acronis True Image Echo Enterprise Server components
- 2.5 Running Acronis True Image Echo Enterprise Server components
- 2.6 Removing Acronis True Image Echo Enterprise Server components
- Chapter 3. General information and proprietary Acronis technologies
- 3.1 The difference between file archives and disk/partition images
- 3.2 Full, incremental and differential backups
- 3.3 Acronis Secure Zone®
- 3.4 Acronis Startup Recovery Manager
- 3.5 Acronis Backup Server
- 3.6 Acronis Snap Restore
- 3.7 Acronis Universal Restore
- 3.8 Backing up to tape libraries and tape drives
- 3.9 Viewing disk and partition information
- Chapter 4. Using Acronis True Image Management Console
- Chapter 5. Using Acronis True Image Echo Enterprise Server (local version)
- Chapter 6. Creating backup archives
- 6.1 Backing up files and folders (file backup)
- 6.2 Backing up disks and partitions (image backup)
- 6.3 Setting backup options
- 6.3.1 Archive protection
- 6.3.2 Source files exclusion
- 6.3.3 Pre/post commands
- 6.3.4 Database support
- 6.3.5 Compression level
- 6.3.6 Backup performance
- 6.3.7 Fast incremental/differential backup
- 6.3.8 Archive splitting
- 6.3.9 File-level security settings
- 6.3.10 Media components
- 6.3.11 Error handling
- 6.3.12 Dual destination backup
- 6.3.13 Wake On LAN
- 6.3.14 Additional settings
- Chapter 7. Restoring the backup data
- 7.1 Considerations before recovery
- 7.2 Restoring files and folders from file archives
- 7.3 Restoring disks/partitions or files from images
- 7.3.1 Starting the Restore Data Wizard
- 7.3.2 Archive selection
- 7.3.3 Restoration type selection
- 7.3.4 Selecting a disk/partition to restore
- 7.3.5 Selecting a target disk/partition
- 7.3.6 Changing the restored partition type
- 7.3.7 Changing the restored partition file system
- 7.3.8 Changing the restored partition size and location
- 7.3.9 Assigning a letter to the restored partition
- 7.3.10 Restoring several disks or partitions at once
- 7.3.11 Using Acronis Universal Restore
- 7.3.12 Setting restore options
- 7.3.13 Restoration summary and executing restoration
- 7.4 Setting restore options
- 7.5 Creating dynamic disks and volumes
- Chapter 8. Scheduling tasks
- Chapter 9. Managing the Acronis Secure Zone
- Chapter 10. Creating bootable media
- Chapter 11. Operations with archives
- Chapter 12. Notifications and event tracing
- Chapter 13. Working with a virtual environment
- Chapter 14. Transferring the system to a new disk
- 14.1 General information
- 14.2 Security
- 14.3 Executing transfers
- 14.3.1 Selecting Clone mode
- 14.3.2 Selecting source disk
- 14.3.3 Selecting destination disk
- 14.3.4 Partitioned destination disk
- 14.3.5 Old and new disk partition layout
- 14.3.6 Old disk data
- 14.3.7 Destroying the old disk data
- 14.3.8 Selecting partition transfer method
- 14.3.9 Partitioning the old disk
- 14.3.10 Old and new disk partition layouts
- 14.3.11 Cloning summary
- 14.4 Cloning with manual partitioning
- Chapter 15. Adding a new hard disk
- Chapter 16. Command-line mode and scripting
to learn more about this procedure. To run the program, press F11 during the server
bootup when you see a corresponding message that tells you to press that key. Acronis
True Image Echo Enterprise Server will be run in the standalone mode, allowing you to
recover the damaged partitions.
If your disk data is totally corrupted and you cannot boot (or if you have not activated
Acronis Startup Recovery Manager), load the standalone Acronis True Image Echo
Enterprise Server version from the bootable media (created by you using Rescue Media
Builder) or RIS-server. Then you will be able to restore the disk from a previously created
image.
2.5.2 Running Acronis True Image Management Console
To run Acronis True Image Management Console, select Start -> Programs -> Acronis
-> Acronis True Image Management Console -> Acronis True Image
Management Console.
2.5.3 Running other Acronis components
Acronis True Image Agents, Acronis Backup Server and Acronis Group Server run as
services immediately after installation and the consequent system reboot (if the latter is
required). Later on they will automatically launch at every system restart. You can stop
and start these programs in the same way as other services.
2.6 Removing Acronis True Image Echo Enterprise Server
components
You can remove any Acronis True Image Echo Enterprise Server component separately by
selecting Control panel -> Add or remove programs -> <The component name>
-> Remove. Then follow instructions on the screen. You may have to reboot your
computer afterwards to complete the task.
In case you remove Acronis True Image Agent or Acronis True Image Echo Enterprise
Server local version from the system, there is an option to keep the Acronis Secure Zone
along with its contents (which will enable data recovery on booting from bootable media)
or remove Acronis Secure Zone.
24 Copyright © Acronis, Inc., 2000-2007