X-FIRE 1200 USER GUIDE GB / IE EDITION LEAVE WITH USER DISTRIBUTED BY Acquisitions of London 24-26 Holmes Road London Nw5 3AB Tel: 24 hours 004 (0)207 482 2949 Email: sales@acquisitions.co.
Any installation or service work carried out on this appliance must only be done by a recognised and Registered Installer in accordance with the Rules in Force. The data plate for this appliance, containing technical information and specifications, can be found to the right of the control tray, near the base of the fire. To access this, the fascia must be removed. We recommend that the X-FIRE 1200 is inspected and serviced by a qualified Gas Fitter once every twelve (12) months.
Contents > Basic Operation Turning the X-FIRE 1200 on Setting the Control Mode Locking the Remote Control Operation from the touch pad 1 2 5 5 > Clearances 6 > Cleaning and Maintenance 8 > Normal operating Sounds and Smells 10 > Warranty Information 11 X-FIRE 1200
1 Basic Operation The X-FIRE 1200 remote control allows you to turn ON and OFF the fire, control the flame height in the Manual mode, or control the room temperature in the Thermostat mode. The remote has a maximum range of 10 meters, and because the remote works by radio frequency, it does not need to be aimed at the X-FIRE 1200 for it to operate.
Basic Operation 2 Switching off the X-FIRE 1200 To turn off the fire, push the OFF button, to shut down the gas flow to the fire and switch it off. The OFF display will now appear in the display. Setting the control mode for the fireplace: There are three different modes for controlling the appliance: > Manual > Automatic > Program Automatic mode allows you to set a temperature, while in manual mode the flame level may be set to HIGH, MEDIUM, LOW & PILOT.
3 Basic Operation Automatic mode: If Auto is pressed in the initial screen, 25ºC (77 º F) appears as the desired temperature in the selected setting. In the bottom row, ↓ and ↑ appear, indicating that we can change the desired temperature value by just pressing the left or middle button. In auto mode the appliance heats until this temperature is reached. Limits are 0-37ºC (3299ºF). Pressing Back (right button), returns to the initial screen. Pressing Back (right button), returns to the initial screen.
Basic Operation 4 Program mode (continued) The daily program screen consists of: A: Selected (including “Daily”). The selected day can be changed by pressing Change (middle button). B: Day schedule graphic. This bar displays the program for the whole day by showing the temperature setting for each hour of the day. To access the day schedule graphic, press ↓ (left button). To change the desired temperature, go to the hour you want to change by pressing → (left button) and then press change (middle button).
5 Basic Operation To Lock / Unlock the remote control buttons: Go into Menu → Lock. Press middle button and then left button for locking the remote. To unlock pres left button and then middle button. Operation from the Touch Pad The touch pad is intended to be used for service/diagnostic purposes and to operate the fire in the event that the remote handset becomes lost or inoperative. If you remove the fascia you will find an electronic touch pad in the lower centre of the fire.
6 Clearances Cabinet Clearances There must be a minimum of 100mm from the sides of the fascia to any protruding side walls or cabinetry. Television Positioning Considerations It is becoming common practice for consumers to mount flat screen TV's above their gas fireplace. Most TV manufacturers have specified in their instructions that the TV should not be installed on, near or above a heat source.
7 Clearances The material that the wall and mantle are made from will also affect the operating temperature of the TV so it is the customers responsibility to satisfy themselves that their TV mounting and mantle design will not exceed the listed maximum operating temperature of their electronic goods. Replacing Batteries When batteries are replaced in either the battery box (inside the fireplace) or n the handset, the unit will require 1 minute afterwards to regain connection.
8 Cleaning and Maintenance Annual Servicing Your X-FIRE 1200 Decorative Gas Fireplace requires that annual service checks be carried out by a Registered Installer to ensure that it will continue to operate in a safe manner. Please ensure that you schedule annual service checks for your X-FIRE 1200 with your local Registered Installer or service agent. Removing the X-FIRE 1200 Fascia Ensure the fascia is allowed to cool before handling. The X-FIRE 1200 fascia attaches to the fire by four hooks.
9 Cleaning and Maintenance Follow the instructions on page 8 in reverse to refit the glass assembly to the fireplace. Do not operate the appliance if the glass has been broken, damaged, or the glass is not properly positioned/hooked onto the appliance. Cleaning your X-FIRE 1200 The unit must be cold before starting any form of maintenance or cleaning. The glass can be cleaned using standard window cleaner.
Sounds and Smells 10 Note: Each time the fire is lit from cold the glass will fog up with condensation. This is normal and the condensation will disappear within a few minutes once the glass heats up. Sounds It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there various types of materials used within your appliance. Listed below are some examples.
11 Warranty WARRANTY TERMS & CONDITIONS: This warranty does not affect your statutory rights.
12 Warranty 2. If the buyer or any other party modifies any part of the Product within the Limited Warranty period without the prior written consent of Acquisitions then the Limited Warranty shall be void. Acquisitions may, at its sole discretion, decide that the Limited Warranty is void in relation to any part of the product, which has been modified. 3.
