PANEL PC 1000 All-in-One 10.
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. ACNODES assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. ACNODES assumes no responsibility for any inaccuracies that may be contained in this document. ACNODES makes no commitment to update or to keep current the information contained in this manual.
Safety Approvals !" CE Marking !" FCC Class A FCC Compliance This equipment has been tested and complies with the limits for a Class-A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications.
Safety Precautions Before getting started, read the following important cautions. 1. The PANEL PC 1000 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 3.
8. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: #"Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
This page does not contain any information.
Table of Contents Chapter 1 Introduction ------------------------------- 1 1.1 1.2 1.3 1.4 1.5 General Description ......................................... Specifications .................................................. Dimensions ...................................................... I/O Outlets........................................................ Utilities Supported ........................................... 1 2 4 5 6 Chapter 2 System Configuration ------------------ 7 2.
This page does not contain any information.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Chapter 1 Introduction This chapter contains the general information and the detailed specifications of the PANEL PC1000. Chapter 1 includes the following sections: $"General Description $"System Specification $"Dimensions $"I/O Outlets $"Utilities Supported 1.1 General Description The PANEL PC 1000 super slim industrial PANEL PCs are mainly designed for industrial automation and some space-constricted embedded applications.
PANEL1000-370 All-in-One PANEL PC User’s Manual 1.2 Specifications Core System for system board $"CPU: Intel Celeron 300 up to 733 MHz; Intel Pentium III 500 up to1.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Built-in Peripherals $"Standard 100W power supply $"2.5” Hard disk (540MB or up) $"10.4” ELO anti-glare analog resistive touch screen with RS- 232 controller sharing COM3 $"System cooling fan NOTE: Optional DC power supplies rated at +12V, +24V and +48V are also available. (See Appendix A) System Specification $"10.
PANEL1000-370 All-in-One PANEL PC User’s Manual 1.3 Dimensions PANEL1000-370 10.
PANEL PC 1000 All-in-One PANEL PC User’s Manual 1.4 I/O Outlets The following figure shows the I/O arrangement of the PANEL PC 1000. The backside of the chassis contains most of the connectors. 1. Ethernet RJ-45 phone jack 8. COM3 2. PS/2 mouse 10. COM1 3. Keyboard 11. VGA port IF 4. External FDD 12. AC inlet 5. 4-channel Digital Inputs/outputs 13. Power switch 6. Parallel port 9. COM2 14. +5V/12V DC outlet 7.
PANEL1000-370 All-in-One PANEL PC User’s Manual 1.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Chapter 2 System Configuration This chapter details the system parts and components with figures. Sections include $" System Major Parts 2.1 $" Panel Mount System Configuration 2.1.1 Front View The figure below shows the front views of PANEL PC1000. 12 3 1. Power LED 2. HDD LED 3.
PANEL1000-370 All-in-One PANEL PC User’s Manual 2.2 Panel Mount The PANEL PC 1000 is mainly designed for panel mount application. To mount the PANEL PC 1000, the standard set of mounting kit (included in the system packaging) is needed. Please refer to the following figure.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Chapter 3 System Installation This chapter describes the installation and the cable connection to the system connectors. See system board User’s Manual that came with your PANEL PC packaging for more details.
PANEL1000-370 All-in-One PANEL PC User’s Manual 3.1 CPU The standard PANEL PC 1000 system already builds in Pentium III-level CPU. When upgrading to a new CPU of the same level, follow the instructions below; 1. To remove the existing CPU requires the use of a chip puller. 2. Locate pin 1 at the corner of the CPU socket and align the CPU’s pin 1 with the pin 1 on the socket. 3. Place the CPU in the socket.
PANEL PC 1000 All-in-One PANEL PC User’s Manual 3.3 HDD The standard PANEL PC 1000 already builds in a 2.5” hard disk drive. If the user intends to remove the existing device for repair or for a higher-capacity one, then follow the installation instructions below. 1. Take out the screws and remove the HDD bracket. Mounting orientation of the HDD brackets on PANEL PC 1000 are not similar to each other. The four screws mounting the PANEL PC 1000 HDD bracket sits at the bottom of the bracket. 2.
PANEL1000-370 All-in-One PANEL PC User’s Manual 3.4 4 x Serial Ports The PANEL PC 1000 provides four onboard serial ports installed on the bottom rear side of the chassis. Arrangements on PANEL PC 1000 specify COM1, COM2, COM3 providing RS-232 interface, and with its RS-422/485 interface connected to COM4. Each serial port comes with +5V/+12V power capabilities on both Pin 1 and Pin 9, ready to accommodate a wide array of serial devices such as fax modem, scanner, serial mouse, touch screen...etc.
PANEL PC 1000 All-in-One PANEL PC User’s Manual 3.5 Parallel Port The printer interface is a 25-pin D-SUB connector. To connect any parallel device, just plug in the device connector to the 25-pin D-SUB. 3.6 VGA The PANEL PC 1000 has an analog RGB interface connector. It is able to connect to an expansion CRT monitor, and the system can display on both the flat panel and the CRT simultaneously. 3.7 Ethernet The PANEL PC 1000 provides an NE2000 compatible Ethernet (RJ-45) interface.
PANEL1000-370 All-in-One PANEL PC User’s Manual 3.8 Digital I/Os The PANEL PC 1000 provides a digital I/O of 4-channel inputs/outputs for simple automation control. For example, it can be used to control the opening and closing of the cash drawer on a POS system. It can also be used for UPS control. It comes with a 15-pin D-SUB connector, and its pin position and pin assignment is shown on the following page. Digital I/O Pin Assignment 1 6 2 11 12 3.
PANEL PC 1000 All-in-One PANEL PC User’s Manual 3.11 External FDD The PANEL PC 1000 does not build in any floppy disk drive into the main system. Rather, it provides a FDD interface. An external FDD cable is provided to connect a standard 3.5” FDD to the system for system O/S and application software installation. The pin positions and pin assignments are listed on the next page. NOTE: 26 25 24 23 22 21 20 19 18 17 16 15 14 An optional external FDD is available for the PANEL1000-370 system.
PANEL1000-370 All-in-One PANEL PC User’s Manual 3.12 Expansion Slot The PANEL PC 1000, this comes as a standard system feature. If the system comes with expansion capability, then the system includes a PCI/ISA expansion riser card to accommodate either an ISA or PCI device at a given time. Due to the internal space limitation, only a half-size expansion card can be adapted. To use the ISA or PCI expansion, refer to the following figure and follow the installation instructions below; 1.
PANEL PC 1000 All-in-One PANEL PC User’s Manual 3.13 System O/S and Software Installation The PANEL PC 1000 is not equipped with any operating system. It builds in a 2.5” HDD and 1.5MB Solid State Disk as memory storage device. As both devices are built in the system chassis, to load any O/S or application software into the computer, an external device is needed to act as a bridge. There are three major ways to load software into the system. 1. Use an external FDD: Attach a 3.
PANEL1000-370 All-in-One PANEL PC User’s Manual This page does not contain any information.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Appendix A Power Supply Specifications Standard AC Power Supplies PANEL PC 1000 Power Supply The power supply used in the PANEL PC 1000 is a 100W open frame power supply. The specifications and features of this special power supply are listed in the following sections.
PANEL1000-370 All-in-One PANEL PC User’s Manual General Specifications $"Efficiency: 86% typ. Environmental Specifications $"Operating temperature range: 0°C to 40°C $"Storage temperature range -40°C to +85°C $"Humidity, non-condensing: 5% ~ 95% $"Altitude: 0 to 10,000 feet International Standards Safety Standards $"Designed to meet the following standards: UL 1950, CSA 22.2 NO.
PANEL PC 1000 All-in-One PANEL PC User’s Manual Optional DC Power Supplies (I) +12V DC Power Supply Input Specifications $"Input voltage range: +9VDC to +18V DC $"Input current: 10A at +12V DC max. Output Specifications $"Load Range: Output Min. Load Rated Load Voltage Accuracy +5V 0A 10A 4.95V to 5.05V +12V 0A 1.5A (open) 11.4V to12.6V -12V 0A 0.3A -11.4V to –12.6V The output range of +12V, -12V and down with +5V setting.
PANEL1000-370 All-in-One PANEL PC User’s Manual General Features $"Efficiency: The efficiency is 70% typical while measuring at nominal line and rated load. $"Protection: For some reason the power supply fails to control itself, the built-in over-voltage protection circuit will shut down the outputs to prevent damage to external circuits. The trip point of crowbar circuit is around 5.7V to 7.0V.
PANEL PC 1000 All-in-One PANEL PC User’s Manual (II) +24V DC Power Supply Input Specifications $"Input voltage range: +18VDC to +36V DC $"Input current: 5A at +24V DC max. Output Specifications $"Load Range: Output Min. Load Rated Load Voltage Accuracy +5V 0A 10A 4.95V to 5.05V +12V 0A 1.5A (open) 11.4V to12.6V -12V 0A 0.3A -11.4V to –12.6V The output range of +12V, -12V and down with +5V setting. At factory, all outputs in 60% rated load conditions, the +5V output is set to between 4.
PANEL1000-370 All-in-One PANEL PC User’s Manual General Features $"Efficiency: The efficiency is 75% typical while measuring at nominal line and rated load. $"Protection: For some reason the power supply fails to control itself, the built-in overvoltage protection circuit will shut down the outputs to prevent damage to external circuits. The trip point of crowbar circuit is around 5.7V to 7.0V.
PANEL PC 1000 All-in-One PANEL PC User’s Manual (III) +48V DC Power Supply Input Specifications $"Input voltage range: +36VDC to +72V DC $"Input current: 3A at +48V DC max. Output Specifications $"Load Range: Output Min. Load Rated Load Voltage Accuracy +5V 0A 10A 4.95V to 5.05V +12V 0A 1.5A 11.4V to12.6V -12V 0A 0.3A -11.4V to –12.6V At factory, all outputs in 60% rated load conditions, the +5V output is set to between 4.95V and 5.
PANEL1000-370 All-in-One PANEL PC User’s Manual General Features $"Efficiency: The efficiency is 75% typical while measuring at nominal line and rated load. $"Protection: For some reason the power supply fails to control itself, the built-in over-voltage protection circuit will shut down the outputs to prevent damage to external circuits. The trip point of crowbar circuit is around 5.7V to 7.0V.
