PC 9XX0 Industrial Panel PC User Manual PC 9XX0: 7 / 8 / 12 / 15” Industrial Panel PC with Dual-Core N2600 1.6GHz Processor 14628 Central Ave, Chino, CA 91710 tel:909.597.7588, fax:909.597.1939 © Copyright 2013 Acnodes, Inc. All rights reserved. Product description and product specifications are subject to change without notice. For latest product information, please visit Acnodes’ web site at www.acnodes.com.
PC 9XX0 Industrial Panel PC Warning! This equipment generates, uses and can radiate radio frequen cy en erg y and if not installed and used in accordance with t he instructions manual, it may cause interference to radio co mmunications. It has b een tested and found to compl y with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reason able pro tection against su ch interference w hen operated in a commercial enviro nment.
PC 9XX0 Industrial Panel PC Packing List Accessories (as tick ed) includ ed in th is package are: AC po wer cable Driv er & manual CD disc Other._ (please specify) Safety Precautions Follow the messages below to prevent your systems from damage: Avoid your system from static electricity on all occasions. Prevent electric shock. Don’t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. Disconnect power when you change any hardware devices.
Table of Contents Wa rning !………………………………………………………………………… ….……..….2 Disc laimer………………………………………………………………….…………………2 Pa cking List…………………………………………………………………………………..3 Safety Prec autions …………………………………………………………………………..3 Chapter 1 Getting Started 1.1 Specifications……………………………………..….……………………..6 1.2 Dimen sion s………………………………...………………………….......7 1.3 Brief Descriptio n………………………………………………….………10 1.4Installation of HDD…………………………………………………………11 Chapter 2 Hardw are 2.1 Mainb oard………………..…….……………………………………..…..15 2.
.1 .2 Installing S oftware (Pro jected Capacitive)..........................................69 5.2 .1 Software Functions(Resistive Touch)...............................................74 5.2 .2 Software Functions(Projected Capa citive)…………………………….85 Figures Fig ure 1.1 :Dime nsion s of PC 90 70………………………………………..…....7 Fig ure 1.2 :Dime nsion s of PC 90 80………………………………………..…....8 Figure 1.3:Dimensions o f PC 9 12 0 …...…………………………………….8 Figure 1.3:Dimensions o f PC 9 15 0 …… …………………………………….9 Fig ure 1.
Chapter 1 System 1.1 Specifications PC 9070 PC 9080 PC 9120 PC 9150 System CPU Atom Cedar View N2600 1.6GHz Dual Core Processors System Chipset NM10 Sys tem Memory Onboard DDR3 2GB 800 MHz IO Port USB Serial/Parallel 2 x USB 2.0 type A, USB4/5 1 x RS-232/422/485 DB-9, COM1, Default RS-232 1 x RS-232 DB-9, COM2 Audio 1 x Line out phone jack LAN 2 x GbE RJ -45 Power 3 pins terminal block connector, DC Power input Storage Space HDD Movable device 1 x 2.5” SATA 2 half size 1 x 2.
P ower Power Input 9~36V DC Mechanical Construction Sliver aluminum front bezel and chassis IP Rating IP65 front panel Mounting Panel mounting, VESA 75 x 75 Dimension (mm) 202 x 149 x 39 231 x 176 x 51 319 x 245 x 51.68 410 x 310 x 54.67 Net Weight (Kgs) 2.3 3.2 4.0 6.
F igure 1.2: Dime nsions of PC9080 F igure 1.
Figure 1.
1.3 Brief Description of PC9XX0 SERIES There are 7”, 8”, 12”,15” Industrial Compact Size Panel PC in PC9XX0 series, which comes with flat front panel touch screen and fanless d esign. It is powered by an Intel Atom N2600 1.6GHz CPU built-in, 2GB DDR III 800 MHz. PC9XX0 series is 9~36VDC wide-ranging power input and IP65 compliant f ront panel.
Figure 1.7: Rear View of PC 9120/ PC 9150 1.4 Installation of HDD(PC9070/PC9080) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 There is a SSD card in the bracket. Gently remove the screw, then carefully pull SSD card.
Step 3 Take out SSD Card bracket. Step 4. You can replace SSD card by unscrewing 4 screws as shown in the picture. Note: 4 screws are packed in the packing lis t. Step 5 There is a SD card hole in the side of the machine. there.
Step 6. Gently screw the screws. Installation of HDD(PC 9120 / PC 9150) Step 1 There are 2 screws to deal with enclosing or removing the chas sis. remove 2 screws.
Step 2 You c an put or remove HDD into the machine by pulling the HDD bracket. Step 3 You can remove HDD by unsc rewing 4 screws in the HDD bracket. Note: 4 screws are packed in the packing list. Step 4 There is a SD hole in the side of machine. You can replace SD card from there .
Chapter 2 Hardware 2.1 Mainboard Specifications Board Size 170mm x 113mm CPU Support Atom N2600 /1.
4-bit digital Input 4-bit digital Output 4-bit digital I/O Pin header via CN3 2-bit digital Input 2-bit digital Output Battery Audio Support CR2477 Li battery by 2-pin header Realtek ALC662 HD audio codec Line-in, Line-out, MIC via 2x6-pin header Audio Line out in phone jack Ke yboard 1 x PS2 keyboard/mouse 1x6 box pin header via CN3 /Mouse Expansion Bus 1 x mini-PCI-express slot 1 x PCI-express via CN3 Touch Ctrl 1 x Touch control header for TCH1 (COM4) Pow er Wide Range DC 9~36V input Management
(units :mm) Figure 2.
2.2 Installations SBC-7106 is a 4" industrial motherboard developed on the basis of Cedarview-M Processors and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE c onfiguration, one VGA port, one HDMI port, one LVDS interface. To s atisf y the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely us ed in various sectors of industrial control. 2.2.
Board Bottom Figure 2.3: J umpers and Connec tors Loca tion_ Board Bottom 2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting.
3. BAT1 : (1.25mm Pitch 1X2 box Pin H eader) 3.0V Li battery is embedded to provide power for CMOS. Pin# Signal Name Pin1 VBAT PIN2 Ground 4. DC_IN1: (5.08mm Pitch 1x3 Pin Connector),DC9V~36V System power input connector 6. Pin# Power Input Pin1 DC+9V~32V Pin2 Ground Pin3 FG VGA1: (CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to VGA Port.
8. JP1: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port. JP1 Pin# Close 1-2 Function COM1 RI (Ring Indicator) (default) Close 3-4 COM1 Pin9=+5V (option) Close 5-6 COM1 Pin9=+12V (option) 9. RS-232: (Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output.
11. COM1: (Type DB9 ), Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. CO M1 port is controlled by pins No.1~6 of JP1,select output Signal RI or 5V or 12 V, For details, please refer to description of JP1 and S_232 and S_422 setting.
RS485 (option): Pin# Signal Name 1 NC 2 NC 3 485- 4 485+ 5 Ground 6 NC 7 NC 8 NC 9 NC BIOS Setup Advanced/W 83627UHG Super IO Conf iguration/Serial Port 1 Configuration RS-485 12 JP2: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select s ignal out of pin 9 of COM2 port.
13. COM2: (Type DB9), Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 RI (Ring Indicator) 16. LED3: LED STATUS. Green LED f or Touch Power status.
23. LINE_OUT: (Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to provide high quality audio I/O ports. Line Out can be connected to a headphone or amplifier. 24. USB45: USB4/USB5 (Double stack USB type A), Rear USB connector, it provides up to 4 USB2.0 ports, High-speed USB 2.0 allows data transf ers up to480 Mb/s ,s upport USB full-speed and low-speed signaling. Each USB Type A Re ceptacle (2 Ports) Current limited value is 1.5A.
28. LED2: LED STATUS. Green LED f or Motherboard Standby Power Good statu s. 31. CN3: (1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO, Two USB 2.0,one PS/2 mouse one PS/2 keyboard,two uart,one PCIe x1,one SMbus.
12V 3P3V_S5 57 58 3P3V_S5 12V_S0 59 60 12V_S0 12V
3 BIOS Setup Description 3.1 Operations after POST Screen After CM OS discharge or BIOS flashing operation,.Press [Delete] k ey to enter CMOS Setup. Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc. BIOS Date: 12/17/2012 02:22:46 Ver: 7106V002 Press DEL or F2 to enter setup A3 After optimizing and exiting CMOS Setup, the P OST screen displayed for the first time is as follows and includes bas ic information on BIOS , CPU, memory, and s torage devices.
3.2 BIOS SETUP UTILITY Press [Delete] key to enter BIOS S etup utility during P OST, and then a main menu containing system summ ary information will appear. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security BIOS Information Save & Exit Intel Reference Code BIOS Vendor American Megatrends Core Version 4.6.5.3 Compliancy UEFI 2.3; PI 1.
: Select Screen System Lan gu age : Select Item [English] Enter: Select System Date [Sun 01/01/2012] +/- : Charge Opt. F1 System Time [00:00:08] : General Help F2: Previous Values Access Level A dministrator F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
3.4 Advanced Settings Aptio Setup Utility – Copyright (C) 2012 Amer ican Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit PCI,PCI-X and PCI PCI Subsystem Settings ACPI Settin gs CPU Con figuration Thermal Configuration ID E Configuration USB Configuration W8362 7UHG Super IO Configuration W8362 7UHG HW Monitor Serial Port Console Redirection PPM Configuration Express Settings : Select Screen : Select Item Enter: Select +/- : Charge Opt.
[Disabled] [Enabled] SERR# Generation: [Disabled] [Enabled] 3.4.2 ACPI Settings Enable ACPI Auto Conf: [Disabled] [Enabled] Enable Hibernation: [Enabled] [Disabled] ACPI Sleep State: [Both S1 and S3 available for OS to choose from ] [Suspend Disabled] [S1 only(CPU Stop Clock) ] [S3 only (Suspend to RAM) ] Lock Legacy Resources: [Disabled] [Enabled] S3 Video Repost: [Disabled] [Enabled] 3.4.
L1 Cache RAM 2x56 k L2 Cache RAM 2x512 k Processor Core Dual Hyper-Threading Supported Hyper-Threading: [Enabled] [Disabled] Execute Disable Bit: [Enabled] [Disabled] Limit CPUID Maximum: [Disabled] [Enabled] 3.4.4 Thermal Configuration CPU Thermal Configuration DTS SMM [Disabled] [Enabled] Platf orm Thermal Configuration Critical Trip Point [POR] Active Trip Point Lo [55 C] Active Trip Point Hi [71C] Passive Trip Point [95] Passive TC1 Value 1 Passive TC2 Value 5 Passive TSP Value 10 3.4.
[AH CI] Misc C onfiguration for hard disk 3.4.6 USB Configuration USB Configuration USB Devices: 1 Drive 1 keyboard Legacy USB Support: [Enabled] [Disabled] EH CI Hand-off: [Disabled] [Enabled] USB hardware delays a USB transfer time-out: [20 sec] [10 sec] [5 sec] [1 sec] Device reset time-out: [20 sec] [10 sec] [30 sec] [40 sec] Device power-up delay [Auto] [Manual] Mass Storage D evic es Multiplecard Reader 1 [Auto] [Floppy] [Forced FDD] [Hard Disk ] [CD-ROM] 3.4.
[R S-485] [R S-422] Serial Port 2 C onf iguration Serial Port 3 C onf iguration UART Mode Selection [RS-485] [R S-422] Serial Port 4 C onf iguration Serial Port 5 Configuration Serial Port 6 Configuration Power Failure [Keep las t state] [Always off ] [Always on] 3.4.8 W83627UHG HW Monitor PC Health Status System temperature1 : +38 System Speed VCORE : N/A : +0.968 V +12V : +12.302 V +3.3V : +3.320 V +1.5V : +1.528 V AVCC : +5.203 V VC C5V : +5.216 V VSB5 : +5.203 V VBAT : +3.334 V 3.4.
[Disabled] [Enabled] Console Redirection Settings 3.4.
3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2012 Ame rican Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Host Bridge Parameters Host Bridge South Bridge : Select Screen : Select Item Enter: Select +/- : Charge Opt. F1 : General Help F2: Previous Values F3:Optimized Defaults F4:Save and Exit ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc. 3.5.
[1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.
IGD Clock Source [External Clock] [Internal Clock ] Fixed Graphics Memory [128MB] [256MB] A LS Support [Disabled] [Enabled] B ack light Control [DC] [PW M] B ack light Logic [Positive] [Negative] B ack light Control Lev [Auto] [Disabled] [Level 8] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] [Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15]
3.5.2 S outh Bridge TP T Devices PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 DMI Link ASP M Control [Enabled] [Disabled] PCI-E xp.
3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Boot Configuration Save & Exit Number of seconds to Setup Prompt Timeout 1 Wait for setup Bootup Numlock State [On] Activation key. 65535(0xFFFF)means Quiet Boot [Disabled] Fast Boot [Enabled] Skip USB [Disabled] Skip PS2 [Disabled] CSM16 Module Version 07.
[E nabled] Fast B oot [E nabled] [Disabled] Skip VGA [E nabled] [Disabled] Skip USB [Disabled] [Enabled] Skip P S2 [Disabled] [Enabled] C SM16 Module Version 07.
[Never] B oot option filter [UEFI and Legacy] [Legac y only] [UEFI only] Launch P XE OpROM poli [Do not Launch] [UEFI only] [Legac y only] Launch Storage OpROM [Legacy only] [Do not Launch] [UEFI only] Launch Video OpROM po [Do not Launch] [UEFI only] [Legac y only] Other PCI device ROM [UEFI OpROM ] [Legacy OpROM]
3.7 Security Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Password Description Save & Exit Set Administrator Password If ONLY the Administrator?s password is set, Then this only limits access to Setup and is Only asked for when entering Setup. If ONLY the User?s password is set, then this Is a power on password and must be entered to Is a power on password and must be entered to Boot or enter Setup.
You will have dir ec t access to BIOS setup without typing any password after s ys tem reboot once the pas swor d is disabled. Onc e the password feature is used, you will be requested to type the password each time you enter B IOS setup. This will prevent unauthorized pers ons from changing your system configurations. Also, the feature is capable of requesting users to enter the password prior to s ys tem boot to control unauthorized access to your com puter.
3.8.
[Enabled, 32MB] [Enabled, 128MB] Video Function Configuration: BIOS SETUP UTILITY Chipset Video Functio n Configuration DVMT Mode Select Options [DVM Mode] Fixed Mode DVMT Mode DVMT/FIXED Memo ry [25 6MB] Boot Display Device [V BIO S-Default] Flat Panel Type [1024x768 18bit 1c] Backlight Control Select Screen Support Select Item [V BIO S-Default] Backlight Control Level [Level 5] +- Charge option Backlight Control Mode [DC] F1 General Help Backlight Image [V BIO S-Default] Adapt
[LVDS] [CRT + LVDS] Flat Panel Type: [1024x 768 18bit 1ch] [640x480 18bit 1ch] [800x600 18bit 1ch] [1280x800 18bit 1ch] [1366x768 18bit 1ch] [1024x 768 24bit 2ch] [1440x900 24bit 2ch] [1600x900 24bit 2ch] [1680x1050 24bit 2ch] [1920x1080 24bit 2ch] Backlight Control Support [V BIOS-D efault] [Both BLC & BIA Disabled] [BLC Enabled] Backlight Control Control: [Level5] [Level0] [Level1] [Level2] [Level3] [Level4] [Level6] [Level7] Note: Panel support PWM Function.
[BIA Enabled at Level3] [BIA Enabled at Level4] [BIA Enabled at Level5] 3.8.2 South Bridge Configuration: Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Exit Exit system setup after Discard Changes and Exit Saving the changes.
[No] Discard Ch anges and Reset Reset Without Savin g Reset without savin g? [Yes] [No] Save Changes Save Setu p Values Save configuration? [Yes] [No] Discard Ch anges Load Previous Values Load Previous Values? [Yes] [No] Restore Defaults Load Optimized Defaults Load optimized Defaults? [Yes] [No] Save user Defaults Save Values as User Defaults Save configuration? [Yes] [No] Restore user Defau lts Resto re User Defau lts Restore User Defaults? [Yes] [No] Launch EFI Sh ell from filesystem device W ARNING Not
3.9 Exit Options BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Options Exit Exit system setup after saving the Save Changes and Ex it Discard Changes and Exit changes Discard Changes F10 key can be used For this operation Load Optimal Defaults Load Failsafe D efaults Select Screen Select Item Enter Go to sub screen F1 General F10 Save and Exit ESC Exit V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Load Optimized D efaults: Load Optimized Defaults? ( F9 key can be used for this operation) [O K] [Cancel] Load Fail-Safe Defaults: Load Fail-Safe Defaults? ( F9 key can be used for this operation) [O K] [Cancel]
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows XP. The software and drivers are included with the motherboard. The contents include Chipset driver, VGA driver, LAN dri vers, Audio driver Installation instructions are given below. Important Note: After installing your W indows operating system (W indows XP), you must install first the Chipset Software Installation Utility before proceeding with the installation of drivers.
4.1 Chipset Driver To install the chipset driver, please f ollow the steps below. Step 1. Select Intel (R) Chipset NM10 Express f rom the list Step 2. Click Next to setup program.
Step 3. Read the license agreement. Step 4. Click Next to continue. Click Yes to accept all of the terms of the license agreement.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Graphics Media Accelerator driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) VGA Chipset Driver. Step 2. Select Installs driver and application files. Click Next.
Step 3. Select I agree. C lick Install. Step 4. C lick Continue Anyway.
Step 5. C lick Continue Anyway. Step 6. To restart the computer, click Yes.
4.3 Network Adapter To install the Network Adapter device driver, please follow the steps below. Step 1. Select Realtek RTL8111D Driver. Step 2. Click Next to continue. Step 3. C lick Install to begin the installation.
Step 4. Click Finish to exist the wizard.
4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the R ealtek ALC662 HD Audio Codec Driver, please f ollow the steps below. Step 1. Select Realtek AL662 Audio Codec Driver from the list Step 2. Click Next to continue.
Step 3. Click Yes, I want to restart my computer now . Click Finish to complete the installation.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems. 5.1 Windows 2000/XP/2003/Vista/WIN7 Universal Driver Installation for PenMount 6000 Series Bef ore installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer.
Step 2. Select Resisti ve Touch. Step 3. Click Next to continue.
Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount W indows Universal Driver. Click Install to start the installation.
Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyw ay.
Step 8. Click Finish to complete ins tallation.
5.1.2 Installing Software (Projected Capacitive) Step 1. Insert the product CD, the screen below would appear. Click touch panel driver. Step 2. Select Projected Capacitive.
Step 3. Click Next to continue. Step 4. Select I accept the terms of the license agreement. Click Next.
Step 5. Tic k Install RS232 interface driver. Step 6. Select None. Step 7. Click OK. Click Next. Click Next.
Step 8. Tic k Support Muti-Monitor System. Step 9. Go to C:\Program Files\eGalaxTouch. Click Next. Click Next.
Step 10. Click Next. Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next.
Step 12. Wait f or installation. Step 13. Click Yes to do 4 point calibration. 5.2.1 Software Functions(Resistive Touch) Upon rebooting, the computer automatically f inds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. W hen the PenMount Control Panel appears, select a device to “Calibrate.
Devic e In this window, you can find out that how many devices be detected on your s ystem. Calibrate This function offers two ways to c alibrate your touch screen. „Standard Calibration? adjusts most touch screens. „Advanced Calibration? adjusts aging touch screens. Standard Calibration Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press ‘ESC’.
Command C alibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.exe -c alibration 0 ( Standard Calibration) Dmcctrl.exe - calibration ($) 0= Standard Calibration 4=Advanc ed Calibration 4 9=Advanced Calibration 9 16=Advanced Calibration 16 25=Advanced Calibration 25 Step 1.
Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a s tylus during Advanced Calibration for greater accuracy.
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Ca libration for greater accuracy.
Setting
About This panel displays information about the PenMount controller and driver version .
Multiple Monitors Multiple Monitors support f rom two to six touch screen displays f or one s ystem. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This f unction supports from two to six touch sc reen displays f or one system. Each monitor requires its own PenMount touch screen control board, either installed inside the dis play or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens. 4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the “Calibration” function. A mes sage to start calibration appears. Click OK.
6. “Touch this screen to start its calibration” appears on one of the screens . Touch the screen. 7. “Touch the red square” messages appear. Touch the red squares in sequence. 8. Continue calibration for each monitor by clicking Standard Calibration and touching the red squares. NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the Multiple Monitor f unction. Just follow the regular procedure for calibration on each of your desktop monitors. 2.
PenMount Monitor has the following f unction PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages. Windows Me/2000/XP support display rotating software pac kages such as: • Portrait?s Pivot Screen Rotation Software • ATI Display Driver Rotate Function • nVidia Display Driver Rotate Function • SMI D isplay Driver Rotate Function • Intel 845G/GE Display Driver Rotate Func tion Configuring the Rotate Function 1.
5.2.2 Software Functions(Projected Capacitive) General In this window, you c an see there is USB Controller. Monitor Mapping to adjust touch panel Add to search for device Click OK to continue.
Setting Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode
Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time
Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy.
Display In this window, it shows the mode of display. Enable Multiple Monitors.
Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function.
Hardw are Saturn Hardware Configuration
About To display information about eGalaxTouch and its version.
