FPC 8084 All-in-One 8.
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. Acnodes Co., Ltd. assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. Acnodes assumes no responsibility for any inaccuracies that may be contained in this document. Acnodes makes no commitment to update or to keep current the information contained in this manual.
Safety Approvals CE Marking FCC Class A FCC Compliance This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications.
Safety Precautions Before getting started, read the following important cautions. 1. The FPC 8084 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 3.
8. Do not open the system s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: 9 Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
This page does not contain any information.
Table of Contents Chapter 1 Introduction............................................1 1.1 General Description .................................................1 1.2 Specifications ...........................................................2 1.2.1 1.2.2 1.2.3 Main CPU Board ......................................................2 I/O System ...............................................................2 System Specification ..............................................9 1.3 Dimensions ..................
3.2.3.3 3.2.3.4 3.2.4.5 3.2.4 3.2.4.1 3.2.4.2 3.2.4.3 Do Calibration .......................................................28 Initializing the PenMount driver ...........................29 Demonstration .......................................................29 Driver Installation- Linux .......................................29 Advance Setup .....................................................29 Install PenMount driver .........................................30 Do Calibration ...........................
FPC 8084 All-in-One PANEL PC User s Manual Chapter 1 Introduction This chapter contains the general information and the detail specifications of the GOT-1840T. Chapter 1 includes the following sections: General Description System Specification Dimensions 1.1 I/O Outlets Utilities Supported Package List General Description The FPC 8084 is a fan-less and compact-size touch panel computer, and is equipped with a 8.4" TFT LCD display and low power consumption CPU, the VIA Eden 667MHz.
FPC 8084 User s Manual Industrial-grade Product Design The FPC 8084 has an incredible design that can be used in different industrial harsh environments. z A fuse helps prevent over-voltage for power input. z Stainless steel back chassis and Aluminum front bezel meets the IP65/NEMA4 standard. z For connecting other devices, the FPC 8084 also features several interfaces: USB, Ethernet, and RS-232/422/485. 1.2 Specifications 1.2.
FPC 8084 User s Manual Ethernet: - Realtek RTL 8100C PCI Bus 10/100M Base-T - Wake-On-LAN - RJ-45 interface equipped Expansion Slot: - one 16-bit PC/104 connector 1.2.3 System Specification 8.4” TFT LCD Disk drive housing: 1 x internal 2.5” drive 100W DC power supply Heat dispensing design One slot for PC/104 Net weight: 18 Kgs Dimension (main body size): 280 x 225 x 61.
FPC 8084 User s Manual 1.3 Dimensions The following diagrams show the dimensions and outlines of FPC 8084.
FPC 8084 User s Manual 1.4 I/O Outlets The following figure shows the I/O locations of the FPC 8084. Most of the I/O connectors are located on the back panel of the FPC 8084. 1 4 5 6 7 2 8 9 3 10 1: USB v1.1 6: Keyboard/Mouse 2: COM4 Port 7: USB v1.
FPC 8084 User s Manual 1.5 Package List When you receive the F P C 8 0 8 4 there are following items in the package. 1. FPC 8084 x 1 2. Panel mount kit x 6 3. Desktop kit x 2 4. Desktop kit screw x 4 5. VESA ARM/Wall-mount kit x 1 6.
FPC 8084 User s Manual Chapter 2 Hardware Installation The FPC 8084 provides lots of flexible ways for you to select different configuration such as HDD, CF card and more. The chapter will show you how to install the hardware. It includes: 2.1 HDD Installation The FPCC 8084 offers a convenient drive bay module for users to install HDD. The FPC 8084 offers one 2.5” HDD drive for users to install. Please follow the steps: 1. Open the HDD back chassis. Unscrew 4 screws of back and 4 screws of side.
FPC 8084 User s Manual 3. Fix the HDD bracket kit to system by 4 screws.
FPC 8084 User s Manual 2.2 CF card Installation The F P C 8 0 8 4 offers a convenient drive bay module for users to install CF card. When installing the CF card, refer to the following instructions and illustration: 1. Open the bottom chassis.
FPC 8084 User s Manual 2. Install user’s CF card. 2.3 Add-on Card Installation The FPC 8 0 84 provides one PC/104 slot. User could install one or two PC/104 card. If user needs the PC/104 Box to protect add-on card, user can order the ‘GOT-PC104-Kit’. When upgrading the add-on card, refer to the following instructions and illustration: 1. Remove the piece by 2 screws.
FPC 8084 User s Manual 2. Install PC/104 cards on the slot. 3. Set the bracket to protect.
FPC 8084 User s Manual 2.4 3 x Serial Ports COM Port Connector: COM1 The connector, COM 1, is a DB-9 connector, and the following table shows the pin assignments of this connector.
FPC 8084 User s Manual COM Port Connectors: COM2, COM3, COM4 The RS-232 pin assignments are listed on the following table.
FPC 8084 User s Manual The RS-422/485 pin assignments for COM2 are listed below. Signa l Name Pin # 2.5 R2-422 RS- 485 1 TX- DATA- 2 No connector No connector 3 TX+ DATA+ 4 No connector No connector 5 RX+ No connector 6 No connector No connector 7 RX- No connector 8 No connector No connector 9 GND GND 10 No connector No connector VGA The FPC 8084 has an analog RGB interface connector.
FPC 8084 User s Manual 4 RJ45 termination 5 RJ45 termination 6 Rx- (Data reception negative) 7 RJ45 termination 8 RJ45 termination 1 2 3 4 5 6 7 8 RJ-45 2.7 Mountings: Panel / Wall / Desktop / VESA There are 5 application options for the FPC 8084, Panel/Wall/Desktop/VESA mountings. 2.7.1 VESA-ARM/Wall-Mount The FPC 8084 provides two ways for VESA mount: 75x75 mm Screw four screws to fix the kit (included in the package) in the back chassis.
FPC 8084 User s Manual 2.7.2 Desktop Kit Assembly The FPC 8084 is designed for desktop application. The standard set of desktop kit is included in the system packaging. Screw 4 screws to fix the kit (included in the package) in the side chassis.
FPC 8084 User s Manual 2.7.3 Panel-mount Kit Assembly The FPC 8084 is designed for panel mount application. To mount the FPC 8084, the standard set of mounting kit (included in the system packaging) is needed.
FPC 8084 User s Manual Chapter 3 Driver Installation 3.1 System FPC 8084 could support with Windows 95, Windows 98 or Windows 2000/XP. To facilitate installation system driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Insert Driver CD and select the “\Driver\”. 2. Select all files and follow the install procedure and press OK. 3.2 Touch Screen 3.2.
FPC 8084 User s Manual Po wer Consum pt ion: 12V: 27mA+ i where (i = v/touch screen sheet R) 5V: 23mA+ i where (i = v/touch screen sheet R) Board Size: 6.0 x 2.0 cm Portrait: Support 90o to 270o screen rotation Stat ic Pro te ction: ESD device option Other s: Touch activate indication LED on board 3.2.2 Driver Installation- Windows 98/2000/XP/CE.NET/XP-Embedded The touch screen of FPC 8084 provides a driver for use with Windows 95, Windows 98 or Windows 2000/XP.
FPC 8084 User s Manual PenMount Control Panel 4.
FPC 8084 User s Manual 5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. 6. Press OK. 3.2.3 Driver Installation- DOS 3.2.3.1 Using “INSTALL.EXE” utility to install PenMount software driver. 1. Insert Driver CD and select the “Driver\Touch screen\DOS\ Install.exe 2.
FPC 8084 User s Manual number 1. For the first time installation, or changing PenMount Touch Screen’s COM port, use PMDETECT (e.g. C:\PENMOUNT\PMDETECT) to check the COM port and IRQ number. PMDETECT will save the correct data to PMOUSE.CFG file for further use. The driver detects your communication COM port and IRQ number from COM1 IRQ4, COM2 IRQ3, COM3…. to COM4 IRQ15. PenMount driver can find the COM port and IRQ number automatically.
FPC 8084 User s Manual right-center point, bottom-center point and left-center point in sequence. After calibration, the data is shown in the screen, press any key to continue the progress. 3. After the calibration, suggest you to test touch screen and display mapped results by choose “3” DRAWING TEST under PM.BAT 3.2.3.4 Initializing the PenMount driver If you don’t have the initialization commands in AUTOEXEC.
GOT-1840T User s Manual 2. Key-in the following words: Setserial /dev/ttyS2 port 0x3e8 irq 10 (set COM3 as touch screen port) 3. Save and exit. 4. Please reboot. 5. After reset system, insert Driver CD. 3.2.4.2 Install PenMount driver 1. Insert Driver CD and select the “Driver\Touch\Linux XFree86 4.x.x Driver V2.1\Driver\penmount_drv.o” 2. Follow the install procedure and press OK. 3. Please reboot system.
FPC 8084 User s Manual 4. Click Start menu and select “PenMount Utilities”. You can see PenMount Control Panel 3.2.4.3 Do Calibration 1. Insert Driver CD and select the “Driver\Touch\Linux XFree86 4.x.x Driver V2.1\Calibration\ pencal-2.00” 2. Follow the install procedure and press OK. 3. Please reboot system.
FPC 8084 User s Manual Chapter 4 Embedded O.S. Installation 4.1 Windows XP Embedded Supported onboard devices are as follows: Onboard Multi I/O Floppy drive 16C550 U ARTs com patible serial port IrD A for wireless comm unication Onboard IDE IDE HDD USB PS2 Keyboard and mouse CRT/LCD display 10/100 base-T Ethernet Compact flash Onboard audio Audio Touch Screen 4.1.1 Penmount Touch Screen FPC 8084 has Penmount touch screen on COM3, which is disabled by default.
FPC 8084 User s Manual 4.2 Windows CE.NET 4.2 Supported onboard devices are as follows: Onboard Multi I/O Floppy drive 16C550 U ARTs com patible serial port IrD A for wireless comm unication Onboard IDE IDE HDD USB PS2 Keyboard and mouse CRT/LCD display 10/100 base-T Ethernet Compact flash Onboard audio Audio Touch Screen 4.2.1 Calibration Touch Screen In this image we add PenMount Touch drivers and utilities. It is customized for 800 x 600. Calibration: 1.
FPC 8084 User s Manual Appendix A Main Board BIOS Setup Appendix A describes the different settings available in the Award BIOS that comes with the SBC84600 CPU card. Also, the instructions on how to set up the BIOS configuration are contained in this chapter. A.1 BIOS Introduction The Award BIOS (Basic Input/Output System) installed in the system ROM supports Intel Celeron processors in a standard IBM-AT compatible I/O system.
FPC 8084 User s Manual In general, the arrow keys are used to highlight items, to select, the and keys to change entries, for help and to quit.
FPC 8084 User s Manual A.2.1 Standard CMOS Setup “Standard CMOS Setup” is used to record some basic hardware configurations in the computer system and set the system clock and error handling. If the motherboard is already installed in a working system, there is no need to enter this option.
FPC 8084 User s Manual according to the memory changed. The following pages describe each item of this menu.
FPC 8084 User s Manual Date The date format is , . show the calendar. day date Press to The day of week, from Sun to Sat, determined by the BIOS, is read only The date, from 1 to 31 (or the maximum allowed in the Month), can key in the numeric al / function key month The month, Jan through Dec. year The year, depends on the year of BIOS Time The time format is accepting either function key or numerical key.
FPC 8084 User s Manual Drive A type/Drive B type The category identifies the types of floppy disk drive A or drive B installed in the computer. None No floppy drive installed 360K, 5.25 in 5.25 inch PC-type standard drive; 360Kb capacity 1.2M, 5.25 in 5.25 inch AT-type high-density drive; 1.2MB capacity 720K, 3.5 in 3.5 inch double-sided drive; 720Kb capacity 1.44M, 3.5 in 3.5 inch double-sided drive; 1.44MB capacity 2.88M, 3.5 in 3.5 inch double-sided drive; 2.
FPC 8084 User s Manual Halt On This field determines whether the system will halt if an error is detected during power up. No errors The system boot will halt on any error detected. (default) All errors Whenever the BIOS detects a non-fatal error, the system will stop and you will be prompted. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.
FPC 8084 User s Manual A.2.2 Advanced BIOS Features This section is used to configure and improve the system and set up some system features according to the user’s preference.
FPC 8084 User s Manual Virus Warning This item protects the boot sector and partition table of the hard disk against accidental modifications. If an attempt is made, the BIOS will halt the system and display a warning message. If this occurs, the user can either continue the operation or run an anti-virus program to locate and remove the problem. NOTE: Many disk diagnostic programs, which attempt to access the boot sector table, can cause the virus warning.
FPC 8084 User s Manual Swap Floppy Drive This allows you to determine whether to enable Swap Floppy Drive or not. W hen enabled, the BIOS swaps floppy drive assignments so that Drive A becomes Drive B, and Drive B becomes Drive A. By default, this field is set to Disabled . Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive type, 40 or 80 tracks. 360Kb type is 40 tracks while 720Kb, 1.2MB and 1.44MB are all 80 tracks. The default value is Enabled .
FPC 8084 User s Manual Typematic Rate (Chars/Sec) This option refers to the number of characters the keyboard can type per second. The default value is 6 .
FPC 8084 User s Manual Video BIOS Shadow Video shadowing increases the video speed by copying the video BIOS into RAM. However, it is still optional depending on the chipset design. The default value of this option is Enabled . Enabled Video BIOS shadowi ng is enabled Disabled Video BIOS shadowi ng is disa bled C8000 - CBFFF Shadow/DC000 - DFFFF Shadow Shadowing ROM reduces available memory between 640KB and 1024KB. These fields determine whether optional ROM is copied to RAM or not.
FPC 8084 User s Manual A.2.3 Advanced Chipset Features Since the features in this section are related to the chipset on the CPU board and are completely optimized, changing the default settings in this setup table are not recommended unless the user is well oriented with the chipset features.
FPC 8084 User s Manual DRAM Timing By SPD This item is selected depending on whether the board has paged DRAMs or EDO (extended data output) DRAMs. DRAM Clock The DRAM clock value is set depending on whether the board has paged DRAMs or EDO (extended data output) DRAMs. The available choices are 66 MHz and Host CLK. SDRAM Cycle Length When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing.
FPC 8084 User s Manual USB Keyboard Support Select “Enabled if the system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The choice: Enabled, Disabled. CPU to PCI Write Buffer W hen this field is Enabled , writes from the CPU to the PCI bus are buffered to compensate for the speed differences between the CPU and the PCI bus. W hen “Disabled , the writes are not buffered and the CPU must wait until the write is complete before starting another write cycle.
FPC 8084 User s Manual A.2.4 Integrated Peripherals This option sets the hard disk configuration, mode and port.
FPC 8084 User s Manual On-Chip IDE Channel0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select “Enabled to activate each channel separately. The choice: Enabled, Disabled. IDE Prefetch Mode The onboard IDE drive interface supports IDE prefetching for faster drive acc esses. If a primary and/or secondary add-in IDE interface are installed, set this field to “Disabled if the interface does not support prefetching.
FPC 8084 User s Manual Onboard Serial Port 1/Port 2 Select an address and corresponding interrupt for the first, second and twist serial ports. The choice: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto. UART 2 Mode This item a is to select UART mode. By default, this field is set to Standard. IR Function Duplex This item is to select the IR half/full duplex function. TX,RX inverting enable This item is to enable the TX, RX inverting which depends on different H/W requirement.
FPC 8084 User s Manual Select a DMA channel for the parallel port for use during ECP mode. The choice: 3, 1.
FPC 8084 User s Manual A.2.5 Power Management Setup The Power Management Setup is to save energy of the system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity.
FPC 8084 User s Manual Video Off Option W hen enabled, this feature allows the VGA adapter to operate in a power saving mode. Always On Monito r will remain on du ring p o we r saving modes. Suspend --> Off Monito r bla nked wh en the sys te m ente rs the Su sp end Susp,Stby --> Off Monito r bla nked wh en the sys te m ente rs eithe r Sus pend or St and by mo de s. All Modes --> Off Monito r blanked wh en the system e nte rs any powe r mode. saving mode.
FPC 8084 User s Manual An input signal on the network 2 awakens the system from a soft-off state.
FPC 8084 User s Manual A.2.6 PNP/PCI Configuration This section describes the PCI bus system configuration. PCI or Personal Computer Interconnect is a system which allows I/O devices to operate at speeds nearing the speed of the CPU when communicating with its own special components. This section covers some very technical items, and it is strongly recommended that only experienced users should make changes to the default settings.
FPC 8084 User s Manual Resource controlled by The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and the Plug and Play compatible devices. However, this capability means absolutely nothing unless using a Plug and Play operating system such as W indows®98. The options available are Auto and Manual. IRQ Resources W hen resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt.
FPC 8084 User s Manual A.2.7 PC Health Status This section is to monitor the current hardware status of core voltages. This is available only if there is hardware monitoring mechanism onboard. Phoe nix – Award BIOS CMOS Setup Utility PC Health Status Current CPU Temp. 22° C/71° C Current System Temp. 22° C/71° C Vcore 1.06V 2.5V 2.5V 3.3V 3.34V 5V 5.12V 12V 11.
FPC 8084 User s Manual A.2.
FPC 8084 User s Manual A.2.9 Load Fail-Safe Defaults This option is to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features.
FPC 8084 User s Manual A.2.10 Load Optimized Defaults This option is to load the default values to the system configuration. These default settings are optimal and enable all high performance features.
FPC 8084 User s Manual A.2.11 Set Supervisor/User Password Either supervisor or user password, or both of them can be set in this option. The differences between them are: 1. supervisor password: can enter and change the options of the setup menus. 2. user password: just can enter but do not have the right to change the options of the setup menus. When this function is selected, the following message will appear at the center of the screen for creating a password.
FPC 8084 User s Manual A.2.12 Save & Exit Setup This is to determine whether or not to accept the modifications. Typing “Y” quits the setup utility and saves all changes into the CMOS memory. Typing “N” brigs back to Setup utility.
FPC 8084 User s Manual A.2.13 Exit Without Saving Select this option to exit the Setup utility without saving the changes made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return to Setup utility.
