FPC 8059 5.
Disclaimers The information in this manual has been carefully checked and is believed to be accurate. Acnodes Corp assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. Acnodes Corp assumes no responsibility for any inaccuracies that may be contained in this document. Acnodes Corp makes no commitment to update or to keep current the information contained in this manual.
Safety Approvals m CE Marking m FCC Class A FCC Compliance This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications.
Safety Precautions Before getting started, read the following important cautions. 1. The FPC 8059 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 3.
5. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.
This page does not contain any information.
Table of Contents Disclaimers ........................................................................ii Safety Approvals................................................................iii FCC Compliance ..............................................................iii Safety Precautions ............................................................. iv C h a p t e r 1 .....................................................................1 Introduction ........................................................
FPC 8059 User’s Manual Chapter 1 Introduction This chapter contains the general information and the detail specifications of the FPC 8059. Chapter 1 includes the following sections: f f f f f 1.1 General Description System Specification Dimensions I/O Outlets Package List General Description The FPC 8059 is a 5.7” fan less TFT VGA touch panel computer. It is equipped with CISI-based low power consumption processor, AMD LX800.
FPC 8059 User’s Manual 1.2 1.2.1 Specifications Main CPU board f CPU: AMD LX800 500MHz f System Chipset: AMD LX + CS5536AD f BIOS: Phoenix-Award 4Mbit with RPL/PXE Ethernet Boot ROM, Smartview and customer CMOS backup. f System Memory: One 184-pin DDR DIMM Maximum up to 1GB 1.2.2 I/O System f Standard I/O: − 2 x serial ports (1 x RS-232, 1 x RS-232/422/485) − 2 x USB Ports 2.
FPC 8059 User’s Manual 1.2.3 System Specification f f 5.7” VGA TFT LCD Disk drive housing: − 1 x Compact Flash T ype II Socket f DC 24V power supply f Heat dispensing design f Net weight: − 2.0 Kgs f Dimension (main body size): − 208.5 x 167.3 x 66.5 mm f Operating temperature: − O° to 45°C ; Relative umidity:50% f Relative humidity: − 10% to 85% @ 40° C, non-condensing f Altitude: − 10,000 ft.
FPC 8059 User’s Manual 4 Introduction
FPC 8059 User’s Manual 1.4 I/O Outlets The following figure shows the I/O locations of the FPC 8059. 1: Power Switch 6: LAN 2: DC power connector 7: USB 2.
FPC 8059 User’s Manual 1.5 Package list When you receive the FPC 8059, there are following items in the package. If you can not find it, please contact Acnodes Corp. distributors. 1. FPC 8059 x 1 2. Panel mount kit x 6 3.
FPC 8059 User’s Manual Chapter 2 Hardware Installation The FPC 8059 provides rich I/O ports and flexible expansions for you to meet different demand such as PCMCIA, WLAN module and so on. The chapter will show you how to install the hardware.
FPC 8059 User’s Manual 2.1 CompactFlash Card Installation FPC 8059 offers one CF slot for users to install Compact Flash card. Please refer to the following instructions and illustration: 1. Remove the rubber cover at left-side. 2. Install Compact Flash card in the FPC 8059.
FPC 8059 User’s Manual 2.2 PC/104 Installation The FPC 8059 offers a convenient expansion for users to install PC/104 module such as PCMCIA, WLAN, COM port card and so on. Please follow the steps: 1. Unscrew screws to remove the bracket. 2. Install PC/104 module.
FPC 8059 User’s Manual 2.3 Serial Port Interface The FPC 8059 has two onboard (RS-232/422/485) & COM2 (RS-232). serial ports, COM1 The pin assignments are listed below: Desc rip tion 1 Data Ca rrier Detect (DCD) 2 Rec eive Da ta (RXD) 3 Tr ans mit Data (TXD) 4 Data Terminal Re ad y (DTR) 5 Ground (GND) 6 Data Set Ready (DSR) 7 Re ques t to Se nd (R TS) 8 Clear to Send ( CTS ) 9 Ring I ndic ato r (R I) In addition, COM1 can be set for RS-232/422/485 by jumper.
FPC 8059 User’s Manual 2.4 Ethernet The FPC 8059 provides an NE2000 compatible Ethernet (RJ-45) interface. For network connection, just plug in one cable end of the FPC 8059 10/100 Base-T Hub into the standard RJ-45 connector.
FPC 8059 User’s Manual C h a p t e r 3 Windows CE.Net 3.1 Survey Form Compact Flash Card System Memory Support Multiple I/O USB 2.0 Keyboard & Mouse Display (MS Flat) Ethernet Audio Touch Screen 3.2 e e e e e e e e e e e 32MB ~ 2GB 256MB ~ 1GB Parallel Port 3 x UARTs compliant Serial Ports 2 x USB 1.1 PS/2 Keyboard & Mouse USB Keyboard & Mouse 320 x 240 Realtek 8139x/810x 10/100M Line-out 5-wire Resistive type Calibrate Touch Screen This image includes a Touch Screen on COM3.
