FPC 71X0 fan less panel PC 12”/15”/17” touch screen Atom all-in-one fan less system User manual
FCC Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditions ： This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class "a" digital device, pursuant to part 15 of the FCC rules.
Copyright Notice This document is copyrighted, 2009. The information provided in this document has been carefully checked for accuracy at the time of publication. No representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed “as is”.
Unpacking the FPC 71X0 Series After unpacking the FPC 71X0 carton, check to make sure all the following items are included and in good condition. FPC 71X0 main system x1 Accessories: AC Power Cord x1 Power Adapter x1 User guide CD & driver x1 Make sure that all of the items listed above are present. If any of the above items is missing, contact your supplier immediately.
Important Safety Precautions 1. Before getting started, read these instructions and save them for later reference. 2. Please disconnect this equipment from any AC outlet before cleaning. Clean with a damp or dry cloth only. Do not spray any liquid cleaner directly. 3. The power outlet socket used to plug in the computer power cord must be located near the system and easily accessible. Do not use outlets on the same circuit of the systems that are regularly switched on and off. 4.
Contents CHAPTER 1 INTRODUCTION ...................................................... 1-1 1.1 General Information .................................................................1-1 1.2 Specifications ..........................................................................1-2 CHAPTER 2 2.1 USING THE SYSTEM ............................................... 2-5 Identifying the System .............................................................2-5 2.1.1 Front view ..................................
4.4.13 I_SP: Internal Speaker Connector ..................................................... 4-20 4.4.14 PW_IN: DC Power In (DC12V) .......................................................... 4-20 4.4.15 COM1: COM Port Connector ............................................................. 4-21 4.4.16 COM5: COM Port Connector ............................................................. 4-21 4.4.17 COM6: COM Port Connector ............................................................. 4-21 4.4.
6.3.2 Windows VISTA ................................................................................. 6-59 6.3.3 Windows POSReady 2009 ................................................................ 6-61 6.4 Audio Driver Installation.........................................................6-63 6.4.1 Windows XP....................................................................................... 6-63 6.4.2 Windows VISTA ...............................................................................
Chapter 1 INTRODUCTION This chapter includes the FPC 71X0 series system background information. General Information Specification Dimensions 1.1 General Information FPC 71X0 series is a fan less mini size panel PC with a compact aluminum chassis as a huge heat sink, which delivers reliable, easy-maintenance, LCD panel and quiet industrial grade mini size computer.
1.2 Specifications SYSTEM CPU • Onboard Intel Atom N270 processors (1.6GHz/FSB 533MHz) • Main Chipsets: Intel i82945GSE+ICH7M System Memory • 2 x 240 pin DIMM up to 2GB DDR2 Graphics • 945GSE integrated GMA950, share system memory (up to 224MB) • Support dual display mirroring/multiple mode Networking • Realtek RTL8111B 10/100/1000 Base-T fast Ethernet • 802.
Resolution y FPC 7120: 800 x 600 y FPC 7150: 1024 x 768 y FPC 7170: 1280 x 1024 Brightness y FPC 7120: 350 cdm2 y FPC 715: 250 cdm/2 y FPC 7170: 300 cd/m2 Storage Device HDD • 1 x 2.5" SATA HDD Compact Flash • 4G or 8G CF card (Optional) I/O PORTS USB • 6 x USB 2.
PS/2 • 2 x PS/2 ports (for keyboard and mouse) Audio • 1x line-out and 1x Mic in VGA • 1 x DB15 VGA interface for dual display MECHANICAL & ENVIRONMENTAL Dimension • FPC 7120: 260 x 351 x 86.5 (H x W x D mm) • FPC 7150: 306 x 412 x 88 (H x W x D mm) • FPC 7170: 350 x 445 x 90.4 (H x W x D mm) Weight FPC 7120: 4.5 KG • • FPC 7150: 5.5 KG • FPC 7170: 7.
Chapter 2 USING THE SYSTEM 2.1 Identifying the System 2.1.1 Front view 2.1.
2.2 First Time System Setup To set up the FPC 71X0 series for the first-time, you should have the following items ready. These items are either included in the accessory box or available from your local computer parts store. • FPC 71X0 Utility CD (Included) • Power cord (Included) • PS/2, AT or USB Keyboard (Not included) • PS/2 or USB Mouse (Not included) • USB CD-ROM Drive (Not included) • Operating System (OS) Installation CD (Not included) 2.2.
ensure the settings will not be erased when the computer is turned off or reset. When the computer is powered on again, the system will read the settings stored in the CMOS RAM and compare them to the equipment check conducted during the power on self-test (POST). If any error or mismatch occurs, an error message will be shown on the screen and the computer will be prompted to run the setup program. 2.2.
2.3 Installation Memory Module The FPC 71X0 series with BI-946ID main board provides two 240-pin DIMM slot. The socket supports up to 2GB DDR2 533MHz. When installing the Memory device, please ： follow the steps below Locate the DIMM slot in the motherboard. 1. Unlock a DIMM slot by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the slot. 3.
Chapter 3 INPUT/OUTPUT CONNECTORS PS/2 Keyboard and PS/2 Mouse The FPC 71X0 series provides two connector supports PS/2 interface. In other cases, especially in embedded applications, a mouse is not used. Therefore, the BIOS standard setup menu allows you to select* “All, But Keyboard” under the “Halt On”. This allows no-keyboard operation in embedded system applications without the system halting under POST.
Network Interface The Realtek RTL8111B Gigabit Ethernet supports the PCI Express 1.0a bus interface for host communications with power management and is compliant with the IEEE 802.3u specification for 10/100Mbps Ethernet and the IEEE 802.3ab specification for 1000Mbps Ethernet. The Ethernet port provides a standard RJ-45 jack. USB Ports Four USB (two is optional) devices may be connected to the system through an adapter cable. Various adapters may come with USB ports.
Chapter 4 SYSTEM MAIN BOARD 4.1 Main Board Dimensions ：170mm Length：170mm Width Height FPC 71X0 User Manual ：33.
4.
4.3 Main Board Jumpers and Jumper Setting Label Function Note JP1 LVDS Panel Power Selector 3x1 header, pitch 2.0 mm JP2 Clear CMOS Contents 3x1 header, pitch 2.0 mm JP3 CPU Frequency Select 3x1 header, pitch 2.0 mm JP4 COM5, COM6 RS232 +5V/+12V Power Setting 2x6 header, pitch 2.0 mm JP6 RS232/422/485 Selector 2x3 header, pitch 2.0 mm JP7 COM3, COM4 RS232 +5V/+12V Power Setting 2x6 header, pitch 2.0 mm JP8 COM1, COM2 RS232 +5V/+12V Power Setting 2x6 header, pitch 2.
4.3.3 JP4: COM5, COM6 RS232 +5V/+12V Power Setting Pin Signal Name 1 JP4 Signal Name Pin RI (Default) RI (Default) 2 3 RI +12v 4 5 RI +5V 6 7 RI (Default) RI (Default) 8 9 RI +12V 10 11 RI +5V 12 COM5 Settings: Pin 1-2 short= standard COM port, Pin 3-4 short=+12V, Pin 5-6=+5V COM6 Settings: Pin 7-8 short= standard COM port, Pin 9-10 short=+12V, Pin 11-12=+5V 4.3.
4.3.6 JBT: Clear CMOS Contents JBT Setting Pin 1-2 Short/Closed Pin 2-3 Short/Closed Function Normal Clear CMOS Note: The DC-12Vpower input connector should be disconnected from the board before clearing CMOS.
4.4 Connectors and Pin Assignment The table below lists the function of each of the board’s connectors.
4.4.1 CN1: Inverter BKL Connector Pin Signal Name 1 Ground 2 Ground 3 ENABKL 4 12V 4.4.2 CN2: 4 Pin Power Output Connector Pin Signal Name 1 +12V 2 GND 3 GND 4 +5V 4.4.3 CN3: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overall, the one pin header support four USB ports (USB 2.0 compliant). Signal Name Pin Pin Signal Name Vcc 1 2 Vcc USB7- 3 4 USB6- USB7+ 5 6 USB6+ Ground 7 8 Ground 4.4.
4.4.5 J1: PW/Reset Switch and Indicator Connector Signal Name Pin Pin Signal Name Ground 1 2 PW-ON Ground 3 4 Reset_SW IDE_LED- 5 6 IDE_LED+ Power_LED+ 7 8 Power_LED- LAN_LED- 9 10 LAN_LED+ 4.4.6 J2: MSR Connector 6 Signal Name Pin Pin Signal Name +5VSB 1 2 KBDATA-IN KBDATA-OUT 3 4 Ground KBCLK-IN 5 6 KBCLK-OUT 1 Note: When MSR is not used, please short jump 2-3 & 5-6 pins. 4.4.
4.4.8 J4: COM2+ CRT (D-SUB 9Pin+D-SUB 15Pin Connector) Signal Name Signal Name Pin Pin DCD, Data carrier detect 1 6 DSR, Data set ready RXD, Receive data 2 7 RTS, Request to send TXD, Transmit data 3 8 CTS, Clear to send DTR, Data terminal ready 4 9 RI, Ring indicator Ground 5 Signal Name Pin Pin Signal Name Red 1 9 +5V Green 2 10 Ground Blue 3 11 NC NC 4 12 SPD2 Ground 5 13 HSYNC Ground 6 14 VSYNC Ground 7 15 SPCLK2 Ground 8 4.4.
4.4.10 LAN1, LAN2: RJ45 + USB0/1, USB2/3 Connectors 4.4.11 SATA1, SATA2: SATA HDD Connector 4.4.12 FAN1, FAN2: CPU Fan Power Connector FAN1, FAN2 is a 3-pin header for CPU fans. The fan must be a 12V (500mA) fan. Pin Signal Name 1 Ground 2 +12V 3 Rotation detection 4.4.13 I_SP: Internal Speaker Connector Pin Signal Name 1 SPK_LN 2 SPK_LO 3 SPK_RN 4 SPK_RO 4.4.
4.4.15 COM1: COM Port Connector Signal Name Pin Pin Signal Name DCD, Data carrier detect 1 2 DSR, Data set ready RXD, Receive data 3 4 RTS, Request to send TXD, Transmit data 5 6 CTS, Clear to send DTR, Data terminal ready 7 8 RI, Ring indicator Ground 9 10 No Connect.
4.4.19 FDD1: Floppy Drive Connector FDD is a slim 26-pin connector and will support up to 2.88MB FDD. Signal Name Pin Pin Signal Name VCC 1 2 INDEX VCC 3 4 DRV_SEL VCC 5 6 DSK_CH NC 7 8 NC NC 9 10 MOTOR DINST 11 12 DIR NC 13 14 STEP GND 15 16 WDATA GND 17 18 WGATE GND 19 20 TRACK NC 21 22 WPROT GND 23 24 RDATA GND 25 26 SIDE 4.4.
4.4.21 LCD1: LVDS Panel Output 4.4.
4.4.
Chapter 5 AWARD BIOS SETUP Power on the computer and immediately press to run the AwardBIOS™ CMOS Setup Utility, the setup main menu will appear: The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to move among the items and press to enter the sub-menu. 5.1 Starting Setup Award BIOS™ has a built-in setup program that allows users to modify the basic system configuration.
5.2 Award BIOS Setup Power on the computer and immediately press to run the AwardBIOS™ CMOS Setup Utility, the setup main menu will appear: The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to move among the items and press to enter the sub-menu. Standard CMOS Setup: This page includes all the items in standard compatible BIOS. Advanced BIOS Features: This setup page includes all the items of Award special enhanced features.
HEISEI Electronics Co., Ltd. 5.3 Standard CMOS Features The standard CMOS features setup allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Use the arrow keys to highlight the item and then use the or keys to select the value you want in each item. Date (mm : dd : yy) Set the system date. Note that if you are running a Windows OS, this item is automatically updated whenever you make changes to the Windows Date.
HEISEI Electronics Co., Ltd. ► Capacity Note that the disk drive capacity (approx.) is usually slightly greater than the size of a formatted disk given by a disk-checking program. ► CYLS. Number of cylinders, Min = 0, Max = 65535 ► HEADS Number of read/write heads, Min = 0, Max = 255 ► PRECOMP Write precomparition, Min = 0, Max =65535. ► LANDZONE Size of landing zone, Min = 0, Max = 65535. ► SECTORS Number of sectors per track, Min = 0, Max = 255. Drive A/B Set Drive A/B type choice.
HEISEI Electronics Co., Ltd. 5.4 Advanced BIOS Features This section allows you to configure your system for basic operation. You can select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security.
HEISEI Electronics Co., Ltd. Virus Warning Allow you to choose the Virus Warning feature for IDE Hard Disk boot sector protection. Enable this item to prevent someone from writing data into this area. Options: Enabled or Disabled Default: Disabled CPU L1 & L2 Cache All processors that can be installed in this motherboard use internal level of L1 cache memory to improve performance. Leave this item at the default value for better performance.
HEISEI Electronics Co., Ltd. Boot Up Num Lock Status This item defines if the keyboard Num Lock key is active when your system is started. Options: On or Off Default: On Typematic Rate Setting This Enables “Typematic Rate” and “Typematic Delay” functions. Options: Enabled, Disabled Default: Disabled Typematic Rate (Chars/Sec) This item sets the rate (characters/second) at which the system retrieves a signal from a depressed key.
HEISEI Electronics Co., Ltd. 5.5 Advanced Chipset Features These items define critical timing parameters of the mainboard. You should leave the items at their default values unless you are very familiar with the technical, specifications of the system hardware. If you change the values incorrectly, you may introduce fatal error or recurring instability into your system.
HEISEI Electronics Co., Ltd.
HEISEI Electronics Co., Ltd. 5.
HEISEI Electronics Co., Ltd.
HEISEI Electronics Co., Ltd. Serial Port 3 Use IRQ Options: IRQ5, IRQ7, IRQ10, IRQ11 Default: IRQ10 Onboard Serial Port 4 This option is used to assign the I/O address and Interrupt Request (IRQ) for the onboard Serial Port. Options: 280, 288, 2A0, 2A8 Default: 288 Serial Port 4 Use IRQ Options: IRQ5, IRQ7, IRQ10, IRQ11 Default: IRQ10 Onboard Serial Port 5 This option is used to assign the I/O address and Interrupt Request (IRQ) for the onboard Serial Port.
HEISEI Electronics Co., Ltd. USB Device Setting ► USB Controller Enable or disable Universal Host Controller Interface for Universal Serial Bus. Options: Enabled, Disabled Default: Enabled ► USB 2.0 Controller Enable or disable Enhanced Host Controller Interface for Universal Serial Bus.
HEISEI Electronics Co., Ltd. 5.7 Power Management Setup ACPI function Options: Disabled, Enabled Default: Enabled ACPI Suspend Type Options: S1 (POS), S3 (STR), S1 & S3 Default: S1 (POS) S1/Power on suspend (POS) is a low power state. In this state, no system context (CPU or chipset) is lost and hardware maintains all system contexts. S3/Suspend to RAM (STR) is a power-down state. In this state, power is supplied only to essential components such as main memory and wakeup-capable devices.
HEISEI Electronics Co., Ltd. Suspend Mode Options: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 1 Hour Default: Disabled Video Off Method Options: Blank Screen, V/H SYNC+ Blank, DPMS Support Default: V/H SYNC+ Blank Video Off In Suspend Options: Yes, No Default: Yes Soft-Off by PWR-BTTN System is turned off if power button is pressed for more than four seconds, or Power button functions as a normal power-on/-off button.
HEISEI Electronics Co., Ltd. 5.8 PnP/PCI Configuration Reset Configuration Data Enabled will reset the ESCD (Extended System Configuration Data) after exiting BIOS Setup if a newly installed PCI card or the system configuration prevents the operating system from loading. This field should usually be left “Disabled”. Options: Enabled, Disabled Default: Disabled Resources Controlled By Enables the BIOS to automatically configure all the Plug-and-Play compatible Devices, e.g.
HEISEI Electronics Co., Ltd. 5.9 Frequency/Voltage Control Auto Detect PCI Clk Options: Disabled, Enabled Default: Enabled Spread Spectrum When the mainboard's clock generator pulses, the extreme values (spikes) of the pulses create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves.
HEISEI Electronics Co., Ltd. 5.10 Load Fail-Safe Defaults When you press on this item, you will get confirmation dialog box with a message similar to: Load Fail-Safe Defaults (Y/N)? N Pressing ‘Y’ loads the BIOS default values for the most stable, minimal performance system operations. This option is for restoring all the default fail-safe BIOS settings. These values are set by the mainboard manufacturer to provide a stable system with basic performance.
HEISEI Electronics Co., Ltd. 5.11 Load Optimized Defaults When you press on this item, you will get confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing ‘Y’ loads the default values that are factory-set for optimal performance system operation. This option is for restoring all the default optimized BIOS settings. The default optimized values are set by the mainboard manufacturer to provide a stable system with optimized performance.
HEISEI Electronics Co., Ltd. 5.12 Set Supervisor/User Password Steps to set supervisor/user password are described as follows: New password setting: 1. While pressing to set a password, a dialog box appears to ask you enter a password. 2. Key in a new password. The password cannot exceed eight characters. Please Enter Your Password 3. System will request you to confirm the new password again. Please Confirm Your Password 4. When completed, new code takes effect.
HEISEI Electronics Co., Ltd. 5.13 Save & Exit Setup Pressing on this item asks for confirmation: Save to CMOS and Exit (Y/N)? Y Press ‘Y’ stores the selections made in the menus of CMOS – a special section of memory that recorded in after you turn your system off. The next time you turn on your computer, the BIOS configures your system according to the Setup selections recorded in he CMOS memory of the chipset. After saving the values the system is restarted again.
5.14 Exit Without Saving Press on this item asks for confirmation: Quit Without Saving (Y/N)? Y This allows you to exit from Setup without storing in CMOS any change. The previous selections remain in effect. This exits from Setup utility and restarts your computer.
Chapter 6 DRIVERS INSTALLATION This chapter offers information of software drivers’ installation. 6.1 Chipset Driver Installation The FPC 71X0 series chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for FPC 71X0 series chipset components. Follow the instructions below to complete the installation. 6.1.1 Windows XP A. Click the folder “Chipset”. C. Click Next. FPC 71X0 User Manual B. Click “Setup” to install. D.
E. Click Next. F. Click “Next” to go on. G. Select “Yes, I want to restart the computer now.”, and click Finish. 6.1.2 Windows VISTA A. Click the folder “Chipset”. FPC 71X0 User Manual B. Click “Setup” to install.
C. Click Next. D. Click Yes to accept the agreement. E. Click Next. F. Click Next. G. Select “Yes, I want to restart the computer now.”, and click Finish.
6.1.3 Windows POSReady 2009 A. Click the folder “Chipset”. B. Click “Setup” to install. C. Click Next. D. Click Yes to accept the agreement. E. Click Next. F. Change the path “C:\WINDOWS\ system32\drivers” and click OK.
G. Change the path “C:\WINDOWS\ system32\drivers” and click OK. H. Change the path “C:\WINDOWS\ system32\drivers” and click OK. I. Change the path “C:\WINDOWS\ J. Change the path “C:\WINDOWS\ system32\drivers” and click OK. system32\drivers” and click OK. K. Change the path “C:\WINDOWS\ L. Change the path “C:\WINDOWS\ system32\drivers” and click OK. M. Change the path “C:\WINDOWS\ system32\drivers” and click OK. FPC 71X0 User Manual system32\drivers” and click Retry. N.
O. Change the path “C:\WINDOWS\ system32\drivers” and click OK. Q. Change the path “C:\WINDOWS\ system32\drivers” and click OK. S. Change the path “C:\WINDOWS\ system32\drivers” and click OK. U. Click Next. FPC 71X0 User Manual P. Change the path “C:\WINDOWS\ system32\drivers” and click Retry. R. Change the path “C:\WINDOWS\ system32\drivers” and click Retry. T. Change the path “C:\WINDOWS\ system32\drivers” and click Retry. V. Click Finish to complete the process.
6.2 Ethernet Driver Installation The FPC 71X0 series is equipped with the Realtek RTL8111B Ethernet controller combines a triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, PCI Express bus controller, and embedded memory. With state-of-the-art DSP technology and mixed-mode signal technology, it offers high-speed transmission over CAT 5 UTP cable or CAT 3 UTP (10Mbps only) cable. Follow the installation steps for Windows XP/VISTA/POSReady 2009. 6.2.
E. Click Next. F. Click Install to start. G. Click Finish to complete the process. 6.2.2 Windows VISTA A. Click the folder “LAN”. FPC 71X0 User Manual B. Click the folder “Vista”.
C. Click “Vista_RTL8168_8101E_8169_ D. Click “setup” to install. 6193_070606”. E. Click Next. F. Click Install to start. G. Click Finish to complete.
6.2.3 Windows POSReady 2009 A. Click the folder “LAN”. C. Click “RTL8168_8101E_664”. E. Click Next. FPC 71X0 User Manual B. Click the folder “Win2k_xp”. D. Click “setup” to install. F. Click Install.
G. Click Finish to complete.
6.3 VGA Driver Installation The FPC 71X0 series offers an integrated VGA/LCD Controller, 2D/3D GUI engine, sharing memory architecture up to 64 MB. The specifications and features are described as follows: The FPC 71X0 series supports CRT and TFT LCD displays. In addition, it also supports CRT and flat panel display mode simultaneously. The FPC 71X0 series can be set in one of three configurations: on a CRT, on a flat panel display, or on both simultaneously.
E. Click Yes to accept the agreement. F. Click Next. G. Click Next to go on. H. Click Finish to complete the process. 6.3.2 Windows VISTA A. Click the folder “VGA”. FPC 71X0 User Manual B. Click the folder “VISTA”.
C. Click “winvista_1583” to install. D. Click Next. E. Click Next. F. Click Yes. G. Click Next. FPC 71X0 User Manual H. Click Next to go on.
I. Click Finish. 6.3.3 Windows POSReady 2009 A. Click the folder “VGA”. B. Click the folder “win2k_xp”. C. Click “Setup” to install. D. Click Next.
E. Click Yes to accept the agreement. F. Click Next. G. Click Next. H. Click Finish to complete the process.
6.4 Audio Driver Installation The FPC 71X0 series is equipped with the VIA HD Codec VT1708A, which is delivering top quality audio performance, supporting the latest 8-channel, 24-bit, 192KHz audio content for an all-round high fidelity experience. Integrating stereo DACs with a 100dB S/N ratio and compliant with the Intel® High Definition Audio Rev. 1.0 specification. Follow the installation steps for Windows XP/VISTA/POSReady 2009. 6.4.1 Windows XP A. Click the folder “AUDIO”. B.
G. Click Next. H. Click Next to continue. I. Click Next. J. Click Finish. 6.4.2 Windows VISTA A. Click the folder “AUDIO”. FPC 71X0 User Manual B. Click the folder “Vista”.
C. Click the folder “v340f”. D. Click “SETUP” to install. E. Click Next. F. Select “I Agree” and click Next. G. Click Next. H. Click Next.
I. Click Next to continue. J. Click Finish. 6.4.3 Windows POSReady 2009 A. Click the folder “AUDIO”. B. Click the folder “XP”. C. Click the folder “v560a”. D. Click “SETUP” to install.
E. Click Next. F. Click I Agree and click Next. G. Click Next. H. Click Next. I. Change the path “C:\WINDOWS\ system32” and click OK. FPC 71X0 User Manual J. Change the path “C:\WINDOWS\ system32\drivers” and click Retry.
K. Click Next. FPC 71X0 User Manual L. Click Finish to complete the process.
6.5 Wireless LAN Driver Installation The Users must make sure which operating system you are using in the FPC 71X0 series before installing the Wireless LAN drivers. Follow the steps below to complete the installation. You will quickly complete the installation. Follow the installation steps for Windows XP/VISTA/POSReady 2009. A. Click the file “Ralink_RT73 “ B. Click Finish to complete the process. C. The screen will show the RaUI window.
6.6 Touch Driver Installation The FPC 71X0 series supports HIGGSTEC Touch. The touchscreen systems consist of a touchscreen and an electronic touchscreen controller. A. Click the folder “Touch”. B. Click “All_In_One_2k_XP_Vista”. C. Click “setup” to install driver. D. Click Next to continue. E. Click Next. F. Click Next.
G. Click OK. H. Click Next. I. Click Next. J. Click Next. K. Click Yes. L. Click Yes.
M. Press the blinking X Symbol until stop N. Click OK to complete the process. blinking.
