Paper type: GB(80kg), Paper Thickness=100 µm // Pages in book=64 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 3.200000 mm RICOH COMPANY, LTD. 15-5, Minami Aoyama 1-chome, Minato-ku, Tokyo 107-8544, Japan Phone: +81-(0)3-3479-3111 Setup Guide Setup Guide Overseas Affiliates U.S.A. RICOH CORPORATION 5 Dedrick Place West Caldwell, New Jersey 07006 Phone: +1-973-882-2000 Spain RICOH ESPAÑA S.A. Avda.
Paper type: GB(80kg), Paper Thickness=100 µm // Pages in book=64 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 3.200000 mm Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.
Setup-F3_FM.book Page i Friday, October 5, 2001 8:27 PM Trademarks Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. Novell, Netware, NDS are registered trademarks or Novell, Inc. PostScript is a registered trademark of Adobe Systems, Incorporated. PCL is a registered trademark of Hewlett-Packard Company. AppleTalk, Apple, Macintosh, TrueType and LaserWriter are registered trademarks of Apple Computer, Incorporated.
Setup-F3_FM.book Page ii Friday, October 5, 2001 8:27 PM Safety Information When using your printer, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
Setup-F3_FM.book Page iii Friday, October 5, 2001 8:27 PM R CAUTION: • Do not eat or swallow toner. • Keep toner (used or unused) and toner bottle out of the reach of children. • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment.
Setup-F3_FM.book Page iv Friday, October 5, 2001 8:27 PM ENERGY STAR Program As an ENERGY STAR Partner, we have determined that this machine model meets the ENERGY STAR Guidelines for energy efficiency. The ENERGY STAR Guidelines intend to establish an international energy-saving system for developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming.
Setup-F3_FM.book Page v Friday, October 5, 2001 8:27 PM Manuals for This Printer Manuals for This Printer The following manuals describe the operational procedures and maintenance of this machine. To enhance safe and efficient operation of this printer, all users should read and follow the instructions carefully. ❖ Quick Installation Guide Describes how to install the printer. ❖ Setup Guide (this manual) Provides information about setting up the printer and its options.
Setup-F3_FM.book Page vi Friday, October 5, 2001 8:27 PM How to Read This Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. R CAUTION: This symbol indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property. * The statements above are notes for your safety.
Setup-F3_FM.book Page vii Friday, October 5, 2001 8:27 PM TABLE OF CONTENTS 1. Getting Started Features of This Printer ............................................................................. 1 Printer Drivers for This Printer.................................................................. 3 Software and Utilities Included on the CD-ROM...................................... 5 Guide to This Printer .................................................................................. 6 Mainframe .......
Setup-F3_FM.
Setup-F3_FM.book Page 1 Friday, October 5, 2001 8:27 PM 1. Getting Started Features of This Printer This printer is designed especially for office work groups. It can be used for network environments and allows you to handle documents efficiently. ❖ High Performance The new 45 print per minute (ppm) engine with RM7000A 250 MHz processor and built-in 10 GB Printer Hard Disk (HDD) reduces waiting time for output. ❖ Versatile Paper Handling Options This printer offers a variety of paper handling options.
Setup-F3_FM.book Page 2 Friday, October 5, 2001 8:27 PM Getting Started ❖ Major Specifications 1 Continuous Printing Speed 45 ppm (A4/letterK, simplex and duplex) Engine Resolution 300 dpi, 600 dpi Printer Languages PCL 5e, PCL 6, RPCS Adobe PostScript 3 Paper Input Capacity 500 sheets × 2 trays + 50 sheets Bypass Tray Max. 3,550 sheets with options Paper Output Capacity 500 sheets Max.
Setup-F3_FM.book Page 3 Friday, October 5, 2001 8:27 PM Printer Drivers for This Printer Printer Drivers for This Printer Printing requires installation of a printer driver for your operating system. The following drivers are included on the CD-ROM that comes with this printer. Printer Language PCL 6 PCL 5e RPCS PostScript3 Windows 95 *1 √ √ √ √ *8 Windows 98 *2 √ √ √ √ *8 √ √ √ √ *8 √ √ √ √ *8 √ √ √ 1 Operating system Windows Me *3 Windows 2000 *4 Windows NT 4.
Setup-F3_FM.book Page 4 Friday, October 5, 2001 8:27 PM Getting Started ❖ Adobe PostScript Printer Drivers and PPD files The Adobe Postscript printer drivers and the PPD files are included on the CD-ROM that comes with this printer. Adobe PostScript printer driver allows the computer to communicate with the printer via a printer language. The PPD files allow the printer driver to enable the printer specific functions. ⇒ p.44 “Windows 95/98/Me - Installing the PostScript Printer Driver” ⇒ p.
Setup-F3_FM.book Page 5 Friday, October 5, 2001 8:27 PM Software and Utilities Included on the CD-ROM Software and Utilities Included on the CD-ROM There are three CD-ROMs that come with this printer. “Operating Instructions”, “Printer Drivers and Utilities” and "Document Management Utility". The following items are included on the CD-ROMs. 1 ❖ Agfa Font Manager Helps you to install new screen fonts, or organize and manage fonts already installed on the system.
Setup-F3_FM.book Page 6 Friday, October 5, 2001 8:27 PM Getting Started Guide to This Printer Mainframe 1 Exterior: Front View 1. Printer Board 6. Output Tray Remove this board when installing some options. Printed output is stacked here with the print side face down. 2. Parallel Interface Connector 7. Control Panel Plug the parallel cable, which connects the printer to your computer, into this socket. Contains keys for printing operation and a panel display that shows the printer status. ⇒ p.
Setup-F3_FM.book Page 7 Friday, October 5, 2001 8:27 PM Guide to This Printer Exterior: Rear View 1 1. Duplex Unit 5. Lower Vertical Paper Feed Cover Allows you to print onto both sides of the paper. Open this cover when accessing the inside of the printer. 2. Duplex Unit Right Cover 6. Power Cord Open this cover when accessing the inside of the printer. Plug this cord into a wall outlet. 3. Bypass Tray Helps to keep components inside the printer from overheating.
Setup-F3_FM.book Page 8 Friday, October 5, 2001 8:27 PM Getting Started Interior 1 1. Fusing Unit 4. Toner Holder When “Replace Maintenance Kit” appears on the panel display, replace this unit. Slide this out when replacing the toner. 2. Transfer Unit When “Replace Maintenance Kit” appears on the panel display, replace this unit. 3. Toner Lock Handle Turn up the lever when replacing the toner. 8 5. Development Unit When “Replace Maintenance Kit” appears on the panel display, replace this unit.
Setup-F3_FM.book Page 9 Friday, October 5, 2001 8:27 PM Guide to This Printer Control Panel 1 1 2 3 5 8 6 9 7 10 11 4 1. Panel Display 5. {On Line}} Key Shows the current status of the printer and error messages. See “Error & Status Messages on the Control Panel” in the Printer Reference on the CD-ROM labeled "Operating Instructions". Press this key to switch the printer between online and offline. 2. Power Indicator Is on when the printer power is on.
Setup-F3_FM.book Page 10 Friday, October 5, 2001 8:27 PM Getting Started 9. {Escape}} Key Press this key to return to the previous condition on the panel display. 10. {Enter #}} Key 1 Press this key to execute menu items selected on the panel display. Press this key to clear some errors. See “Troubleshooting” in the Printer Reference on the CD-ROM labeled "Operating Instructions". 11. {U} {T} Keys Use these keys to increase or decrease values on the panel display when making settings.
Setup-F3_FM.book Page 11 Friday, October 5, 2001 8:27 PM 2. Installing Options R CAUTION: • Before installing options, the machine should be turned off and unplugged for at least thirty minutes. Components inside the machine become very hot, and can cause a burn if touched. • Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged abruptly, it could become damaged. Damaged plugs or cords can cause an electrical or fire hazard.
Setup-F3_FM.book Page 12 Friday, October 5, 2001 8:27 PM Installing Options 2. Large Capacity Tray RT36 5. Finisher SR730 Holds up to 1500 sheets of plain paper. (80 g/m2, 20 lb. bond) If you want to install the Large Capacity Tray RT36, contact your sales or service representative. 3. Bridge Unit Type1045 2 This unit is necessary when using the Finisher or the Mailbox. If you want to install the Bridge Unit Type1045, contact your sales or service representative. 4.
Setup-F3_FM.book Page 13 Friday, October 5, 2001 8:27 PM Available Options How to Use the Screwdriver The screwdriver (A) is attached in the standard paper tray (Tray 1). It is used to install options. To easily drive a screw, first place the screw in the screwdriver, and then tighten the screw.
Setup-F3_FM.book Page 14 Friday, October 5, 2001 8:27 PM Installing Options Installing Options Installing Memory Unit TypeC R CAUTION: • Do not touch the inside of the printer board compartment. It may cause a machine malfunction or a burn. 2 Important ❒ The memory unit can be damaged by a small amount of static electricity. Before touching it, touch some metal to remove static electricity from you.
Setup-F3_FM.book Page 15 Friday, October 5, 2001 8:27 PM Installing Options G Align the printer board with the top and bottom rails in the printer, and then insert the printer board slowly until it clicks into place. Installing Paper Bank PS430 R CAUTION: • Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged abruptly, it could become damaged. Damaged plugs or cords can cause an electrical or fire hazard. 2 • When lifting the machine, use the grips on both sides.
Setup-F3_FM.book Page 16 Friday, October 5, 2001 8:27 PM Installing Options B Remove the tape that holds the Paper Bank, and then remove the packing material. D Align the printer over the Paper Bank, and then lower it carefully onto the Paper Bank. Important ❒ Do not remove the tape that holds the connector cable inside the connector cover on the back of the Paper Bank in this step. It is removed in step L. 2 TAPP801E Important ❒ The printer should be held by at least two people.
Setup-F3_FM.book Page 17 Friday, October 5, 2001 8:27 PM Installing Options F Pull the second paper tray (Tray 2) until it stops. After that, lift it slightly, and then pull it out. I Set the second paper tray (Tray 2) into the printer. 2 TAPH221E G Pull out the first paper tray (Tray 1) , and take the screwdriver (A A) from the tray. J Open the lower vertical paper feed cover on the right side of the Paper Bank (A A ).
Setup-F3_FM.book Page 18 Friday, October 5, 2001 8:27 PM Installing Options M Close the connector cover. 2 Note ❒ Print a configuration page to confirm that the Paper Bank is properly installed. See "Printing a Configuration Page" in the Printer Reference on the CDROM labeled "Operating Instructions". Installing Printer Hard Disk Type4510 R CAUTION: • Do not touch the inside of the printer board compartment. It may cause a machine malfunction or a burn.
Setup-F3_FM.book Page 19 Friday, October 5, 2001 8:27 PM Installing Options D Remove the two screws locking the printer board. The screws are needed to lock the printer board afterwards. G Hold the handle, and carefully pull out the printer board halfway. 2 E Remove the two screws locking the Printer Hard Disk cover next to the printer board. H Connect the bigger plug of the power cord to the printer board. I Connect The screws are needed to lock the cover afterwards.
Setup-F3_FM.book Page 20 Friday, October 5, 2001 8:27 PM Installing Options J Connect the power cord to the Printer Hard Disk. M Align the printer board with the top and bottom rails in the printer, and then insert the printer board slowly until it stops. 2 K Connect the connector to the Printer Hard Disk. N Lock the printer board with the two screws you removed in step D. L Lock the Printer Hard Disk cover with the two screws you removed in step E.
Setup-F3_FM.book Page 21 Friday, October 5, 2001 8:27 PM Installing Options Formatting Printer Hard Disk Type4510 If you are formatting the Printer Hard Disk from the menu, follow the procedures below while using the control panel. A Press {Menu}}. “Menu” appears on the panel display. B Press {U} or {T} to display the “Maintenance” menu. Menu: Maintenance C Press {Enter q}. The following message appears on the panel display. Menu: Image Density D Press {U} or {T} to display “HDD Format”.
Setup-F3_FM.book Page 22 Friday, October 5, 2001 8:27 PM Installing Options Installing 1394 Interface Unit Type 4510 R CAUTION: • Do not touch the inside of the printer board compartment. It may cause a machine malfunction or a burn. 2 Important ❒ In Windows 2000, the 1394 Interface Unit can only be used with Service Pack 1 or later.
Setup-F3_FM.book Page 23 Friday, October 5, 2001 8:27 PM Installing Options E Hold the handle, and carefully pull out the printer board. I Lock the 1394 Interface Unit cover with the two screws you removed in step G. 2 F Put the printer board on a flat surface. J Align the printer board with the the two screws locking the 1394 Interface Unit cover. top and bottom rails in the printer, and then insert the printer board slowly until it stops.
Setup-F3_FM.book Page 24 Friday, October 5, 2001 8:27 PM Installing Options Note ❒ Be sure to return the screwdriver to the paper tray after using it. ❒ Print a configuration page to confirm that the unit is properly installed. See "Printing a Configuration Page" in the Printer Reference, on the CD-ROM labeled "Operating Instructions". 2 Connecting the 1394 interface cable to the printer A Attach the 1394 interface cable to the jack on the board. Both jacks are available.
Setup-F3_FM.book Page 25 Friday, October 5, 2001 8:27 PM Installing Options • If the printer driver for the connected printer has already been installed, the icon is automatically added to the Printers folder. In this case, driver installation is not necessary. However, since the 1394 Interface Unit does not support bidire c t io n a l t r an s m i ss io n s , i f options are installed, set up options from the Printer Driver Properties. See p.37 “Installing the Printer Driver and Software”.
Setup-F3_FM.book Page 26 Friday, October 5, 2001 8:27 PM Installing Options M Click [Have Disk…]. Installing the Printer Driver You need the Microsoft Windows Me CD-ROM for the installation. To find out whether the Windows Me CD-ROM supplied by another supplier includes the IPP driver, contact the each supplier. 2 A Insert the Windows Me CD-ROM into the CD-ROM drive. B Auto Run will start the Windows Millennium CD-ROM. C Click [Browse This CD]. A window showing the contents of the CD-ROM appears.
Setup-F3_FM.book Page 27 Friday, October 5, 2001 8:27 PM Installing Options Configuration and Usage from a Web Browser Preparation If you want to use this printer from a Web browser, its IP address must be specified and the TCP/IP protocol (IP over 1394) set on the control panel. For more information, see p.34 “IEEE 1394 Configuration”. When you browse the printer on the network by the Web browser, you need not to use the proxy server.
Setup-F3_FM.book Page 28 Friday, October 5, 2001 8:27 PM Installing Options Troubleshooting IEEE 1394 Printer Removal Utility If you cannot print when the printer is connected via the 1394 Interface Unit or error messages appear, follow the procedure: 2 A Make sure the 1394 Interface Unit is installed properly. B Make sure the IEEE 1394 cable is connected properly. C Restart the computer. If the problem still exists, go to step D. D Disconnect all the IEEE 1394 cables from the computer.
Setup-F3_FM.
Setup-F3_FM.
Setup-F3_FM.book Page 31 Friday, October 5, 2001 8:27 PM 3. Configuring the Printer for the Network Configuring the Printer for the Network with the Control Panel After installing the optional Network Interface Board, configure it for the network using the printer's control panel. Configure the printer for the network using the printer's control panel. The following table shows the control panel settings and their default settings. These are included in the “Host Interface” menu.
Setup-F3_FM.book Page 32 Friday, October 5, 2001 8:27 PM Configuring the Printer for the Network D Press {U} or {T} to display “Network Setup”. Host Interface: Network Setup E Press {Enter #}}. The following message appears on the panel display. 3 Network Setup: IP Address F Select the protocol you want to use. Note ❒ Do not select protocols that are not used on your network. Network Setup: IP Address B Press {Enter #} }. The current IP address appears on the panel display. IP Address: 011.022.
Setup-F3_FM.book Page 33 Friday, October 5, 2001 8:27 PM Configuring the Printer for the Network with the Control Panel H If you use TCP/IP, you should assign “Subnet Mask” and “Gateway Address” following the same procedure for entering the IP address. I If you use TCP/IP, you can make settings for “Network Boot”. You can select how to assign the printer's address using the computer. Select one of the items below if necessary. • None (Default) • DHCP A Press {U} or {T} to display “Network Boot”.
Setup-F3_FM.book Page 34 Friday, October 5, 2001 8:27 PM Configuring the Printer for the Network IEEE 1394 Configuration Configure the printer for using in the IEEE 1394 environment. The following table shows the control panel settings and their default settings. These are included in the "Host Interface" menu. Setting Name 3 C Press {Enter #}}. Value IP Address1394 011.022.033.044 Subnet Mask1394 000.000.000.000 IP over 1394 IP over 1394 SCSI print Active A Press {Menu}}.
Setup-F3_FM.book Page 35 Friday, October 5, 2001 8:27 PM IEEE 1394 Configuration G Set "SCSI print" in the same way. H Assign the IP address to the print- E Repeat steps C and D to enter the IP address. IP Address1394: 192.168.000.011 er. Note ❒ To get the IP address for the printer, contact your network administrator. A Press {U} or {T} until the following message appears. IEEE 1394 Setup: IP Address1394 B Press {Enter #} }. The current IP address appears on the panel display.
Setup-F3_FM.
Setup-F3_FM.book Page 37 Friday, October 5, 2001 8:27 PM 4. Installing the Printer Driver and Software This manual assumes that you are familiar with general Windows procedures and practices. If you are not, see the documentation that comes with Windows for details. Installation Method The following table shows how to install the printer drivers and software.
Setup-F3_FM.book Page 38 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Quick Install Auto Run will start the installer automatically when you load the CD-ROM in the CD-ROM drive. By selecting Quick Install, you can install the necessary software easily. TCP/IP requires the following: • This machine must be connected to the network through the network interface cable. • This machine must be turned on. • The TCP/IP protocol must be configured.
Setup-F3_FM.book Page 39 Friday, October 5, 2001 8:27 PM Quick Install F Click to select a model name you want to use when the "Select Printer" dialog box appears. Note ❒ For a network connection with TCP/IP, select the printer whose IP address is displayed in [Connect To]. ❒ For parallel connection, select the printer whose printer port is displayed in [Connect To]. G Click [Install]. H Follow the instructions on the screen.
Setup-F3_FM.book Page 40 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Installing the PCL 6/5e Printer Driver Installing the PCL 6/5e Printer Driver Two kinds of PCL printer drivers, PCL 6 and PCL 5e, are provided with this printer. We recommend PCL 6 as your first choice. Limitation ❒ If your system is Windows 2000 or Windows NT 4.0, installing a printer driver by Auto Run requires Administrators permission.
Setup-F3_FM.book Page 41 Friday, October 5, 2001 8:27 PM Installing the PCL 6/5e Printer Driver Setting up options Important ❒ If the printer is equipped with certain options, you should set up the options with the printer driver. Limitation ❒ In Windows 2000, changing the printer settings requires Manage Printers permission. Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account that has Manage Printers permission.
Setup-F3_FM.book Page 42 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Installing the RPCS Printer Driver Installing the RPCS Printer Driver Limitation ❒ If your system is Windows 2000 or Windows NT 4.0, installing a printer driver by Auto Run requires Administrators permission. When you install a printer driver by Auto Run, log on using an account that has Administrators permission.
Setup-F3_FM.book Page 43 Friday, October 5, 2001 8:27 PM Installing the RPCS Printer Driver Setting up options Important ❒ If the printer is equipped with certain options, you should set up the options with the printer driver. Limitation ❒ In Windows 2000, changing the printer settings requires Manage Printers permission. Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account that has Manage Printers permission.
Setup-F3_FM.book Page 44 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Installing the PostScript Printer Driver This section describes basic instructions for installing the PostScript printer driver. The actual procedure may differ depending on the operating system. Follow the appropriate procedures below. Important ❒ When updating the printer driver by installing the latest version, you should uninstall that of former version if any.
Setup-F3_FM.book Page 45 Friday, October 5, 2001 8:27 PM Installing the PostScript Printer Driver Setting up options Important ❒ If the printer is equipped with certain options, you should set up the options with the printer driver. A Click [Start] on the taskbar, point to [Settings], and then click [Printers]. The [Printers] window appears. B Click to select the icon of the printer you want to use. C On the [File] menu, click [Properties]. The Printer Properties appear.
Setup-F3_FM.book Page 46 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software D Select [PostScript 3 Printer Driver]. [Add Printer Wizard] starts. E Click [Next]. F Check [Local Printer] and then click [Next]. A dialog box for selecting the printer port appears. G Select the check box of the port you want to use, and then click [Next]. A dialog box for selecting the printer appears. H Select the printer you want to use, and then click [Next].
Setup-F3_FM.book Page 47 Friday, October 5, 2001 8:27 PM Installing the PostScript Printer Driver Windows NT 4.0 - Installing the PostScript Printer Driver Installing the printer driver Limitation ❒ Installing a printer driver requires Administrators permission. When you install a printer driver, log on using an account that has Administrators permission. Important ❒ The CD-ROM containing the Windows NT Server operating system version 4.
Setup-F3_FM.book Page 48 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Setting up options Limitation ❒ Changing the printer settings requires Manage Printers permission. Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account that has Manage Printers permission. Important ❒ If the printer is equipped with certain options, you should set up the options with the printer driver.
Setup-F3_FM.book Page 49 Friday, October 5, 2001 8:27 PM Installing the PostScript Printer Driver • On Windows 2000 and Windows NT 4.0, [Enable bi-directional support] must be selected and [Enable printer spooling] must not be selected on the [port] tab. ❖ When connecting with the network • SmartNetMonitor for Admin or SmartNetMonitor for Client included on the CD-ROM must be installed, and the TCP/IP protocol must be used. Using Adobe PageMaker Version 6.0 or 6.
Setup-F3_FM.book Page 50 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Installing the SmartNetMonitor for Client/Admin Limitation ❒ If your system is Windows 2000 or Windows NT 4.0, installing software by Auto Run requires Administrators permission. When you install a printer driver by Auto Run, log on using an account that has Administrators permission. A Close all applications that are running. B Insert the CD-ROM into the CD-ROM drive.
Setup-F3_FM.book Page 51 Friday, October 5, 2001 8:27 PM Installing the Agfa Monotype Font Manager 2000 Installing the Agfa Monotype Font Manager 2000 Limitation ❒ If your system is Windows 2000 or Windows NT 4.0, installing software by Auto Run requires Administrators permission. When you install a printer driver by Auto Run, log on using an account that has Administrators permission. A Close all applications that are running. B Insert the CD-ROM into the CD-ROM drive.
Setup-F3_FM.book Page 52 Friday, October 5, 2001 8:27 PM Installing the Printer Driver and Software Macintosh Macintosh - Installing the PostScript 3 Printer Driver It is necessary to install a printer driver and a PPD file to print from a Macintosh. Follow these steps to install a printer driver and a PPD file on Macintosh running the 8.6 operating system or later up to 9.1. A Insert the CD-ROM into the CD-ROM drive. B Double-click the CD-ROM icon. C Double-click the [PS DRIVER] folder.
Setup-F3_FM.book Page 53 Friday, October 5, 2001 8:27 PM Macintosh D Click [Setup]. E Click the printer description file you want to use, and then click [Select]. The PPD file is set up, and the [Adobe PS] icon appears at the left of the machine name in the list. Next, follow the procedure on p.53 “Setting Up Options” to make the option settings, or close the [Chooser] dialog box. Setting Up Options A On the [Apple] menu, select [Chooser]. B Click the [Adobe PS] icon.
Setup-F3_FM.
Setup-F3_FM.book Page 55 Friday, October 5, 2001 8:27 PM P PageMaker 6.0 or 6.5, 49 Panel Display, 9 Paper Bank, 6, 11, 15 paper tray, 6 parallel interface connector, 6 PCL 5e, 3, 40 PCL 6, 3, 40 PostScript, 4 Windows 2000, installing, 45 Windows 95/98/Me, installing, 44 Windows NT 4.
Setup-F3_FM.
