0W LED COLOR SPOT LED-PS10D RGBW User Manual Professional Entertainment Technology
TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Installation 4. How to Control the Unit 4.1 Control Panel 4.2 Master/Slave operation 4.2 Easy controller 4.4 Universal DMX controller 5. DMX 512 Configuration 6. DMX 512 Connection 7. Trouble Shooting 8.
1. Safety Instruction WARNING Please read the instruction carefully which including important information about the installation, y Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. y Unpack and check carefully there is no transportation damage before using the unit. y Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
y y y y y Voltage: AC 100-240V~50/60Hz LED: 1 x 10W quad-color LED, 50,000 hrs rated Power Consumption: 14.9W Dimension: 187 x 156 x 115 mm Weight: 2.0kg 3. Installation The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight.
1 Hanging bracket: With 2 knobs on both sides to fasten the unit and a mounting hole ○ to fix a mounting hook Lens: Turn the lens to change the focus and obtain sharp gobos 3 DIP Switches: Set the different function settings ○ 4 Microphone: Receives the sound to control the unit ○ 5 ○ 6 Only for remote control: ○ Connecting with CA-8/CA-9/CA-9RTX to control the unit for Stand by, Function and Mode. 7 Safe Ring: For attached the safe cable.
4.3 Easy Controller (by CA-8/CA-9/CA-9RTX) The easy remote control is used only in master/slave mode. By connecting to the 4-pin jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by, Function and Mode selection Blackout Function Mode Blackout the unit Strobe 1. Synchronous strobe in 1. white 2. 2. Sound strobe in white 3. 3. Sound strobe in color 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
DMX 512 Address Chart: Dip-switch es #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 Value 1 2 4 8 16 32 64 12 8 25 6 Channel mode Dip switch 10 OFF Channel 1：dip / on: #1 (=1) Channel 2：dip / on: #3 (=4) Channel 3：dip / on: #1,#2, #3 (1+2+4=7) Channel 4：dip / on: #2, #4 (2+8=10) Dip switch 10 ON Channel 1：dip / on: #1 (=1) Channel 2：dip / on:, #1, #3 (1+4=5) Channel 3：dip / on: #1, #4 (1+8=9) Channel 4：dip / on: #1, #3, #4 (1+4+8=13) 6-
5.
6. DMX 512 Connection The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels. 1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable. 2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. 3.
7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 11. Check the connection of power and main fuse. 12. Measure the mains voltage on the main connector. B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3.
8. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 20 days.
Широкий ассортимент оборудования ACME на www.maxlight.
