BLED‐7TC BLED‐7TC‐A BLED‐7TC‐B BLED‐7TC‐AB User Guide Please read the instruction carefully before use
Contents 1. Safety Instructions....................................................................................................2 2. Technical Specifications ............................................................................................3 3. Installation................................................................................................................4 3.1 The Method of Connecting Wireless modules ...................................................4 4. How to Set the Fixture....
1. Safety Instructions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING y Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet. y Unpack and check carefully there is no transportation damage before using the fixture.
Warning: y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. y Do not open the unit within five minutes after switching off. y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Caution: There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In the unlikely situation, your unit may require service, please contact your nearest dealer. 2.
Note: BLED‐7TC (Without Antenna and Battery) BLED‐7TC‐A (With Antenna, without Battery) BLED‐7TC‐B (With Battery, without Antenna) BLED‐7TC‐AB (With Antenna and Battery) 3. Installation The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight.
4. How to Set the Fixture 4.1 Control Panel ① Display: To show the various menus and the selected functions.
Mode function. ⑧ DMX output: For DMX512 link, use 3/5‐pin XLR plug cable to link the next unit. ⑨ DMX input: For DMX512 link, use 3/5‐pin XLR plug cable to input DMX signal. ⑩ Power Switch: Turns On/Off the power. 4.2 The Battery Indicator & Charge Battery Indicator: The LED (Battery indicator) on the front of unit lets you know the current status of the battery: - When the Orange LED is fully lit the fixture is fully charged. - When the Orange LED begins flash slowly, the charge is getting low.
1, A and B are closed (1); 2, To rotate C button, and change the angle as you required like (2), (3). 4.4 Main Function To select any of the given functions, press the MENU button to show the required option on the display. Select the function with the ENTER button and the display will blink. Use the DOWN and UP buttons to change the mode. Once the required mode has been selected, Press the ENTER button to store. To go back to the main menu without any changes press the MENU button.
8A
Color Mode. Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (show 16) or you select (color 1) or … or (manual setting).
button and the display will blink. Use DOWN and UP button to select the (chase 16) or (chase 1) or … or (fade). Once the chase has been selected, press the ENTER button to confirm, then press DOWN and UP button to select (slowest) or … (fastest), press ENTER button to store or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again.
Channel mode Press the MENU button up to when the is shown on the display. Pressing the ENTER button and the display will blink. Use the DOWN and UP button to select the mode) or (4 channel mode) or (4 channel mode) or (4 channel (4 channel mode) or (6 channel mode). Once the mode has been selected, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again.
the indicator on the unit will blink which means the unit is connecting the Wireless Transmitter, the indicator stops blinking after 6 seconds, the unit has connected the DMX transmitter successfully. Now both the LED on the unit and the status LED on the Wireless Transmitter will begin to flash, indicating that they are both searching for a signal. If the signal connection is successful, the status LED on the transmitter will grow green, and unit will display the DMX address that you set before.
Display Inversion It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the (display inversion) or (display normal). Once select, press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds. To go back to the functions without any change press the MENU button again.
5.1 Universal DMX controller The fixture can be set the DMX address remotely by universal DMX controller. First, you need to programming two scenes into a chase, and then link the fixtures to the universal DMX controller. When you run the chase, all the fixtures of the chain will be set the series DMX address automatically. The fixture uses four channels. Please refer to the following diagram to set the address for the first four units. 5.
6.
7. DMX 512 Connection The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter‐cable. 2. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable.
8. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3.
9. Cleaning And Maintenance The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics. y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 2004/108/EC. EN55103-1: 2009 ; EN55103-2: 2009; EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.
Innovation, Quality, Performance
