Specifications

11
Tech Support: 855-ONE-ZURN
www.zurn.com
• 1/2”, 3/4”, 1”, 1
1
/
4
”, 1
1
/
2
”, 2”
• Pressure rated 300 psi
• Spring range 25 to 75 psi; factory set at 50 psi
• Maximum temperature 180°F
• All bronze body and bell housing provides durability and long life
• Built-in by-pass prevents buildup of excessive system pressure caused
by thermal expansion
• Integral stainless steel strainer with separate access cover
• Nylon reinforced Buna-N diaphragm
• Balanced piston design
• May be installed in any position
• All internal parts corrosion-resistant
• Serviceable in-line
• Available tapped and plugged for gauge (optional)
• Available tapped with gauge (optional)
• Available with BSP threads 1/2” through 2” (optional)
• ASSE
®
Listed 1003, IAPMO
®
Listed, CSA
®
Certified, City of Los Angeles
Model 600 Union end connection standard and available 1/2”
through 2” in FNPT
Model 600C Union end connection standard, available 1/2”
through 2” female copper sweat
Model 600L Less built-in by-pass
Model 600HR Spring range is 75 – 125 psi, factory set at 85 psi
Model 600HLR Spring range is 10 – 125 psi, factory set at 50 psi
Model 600LU Less union; female by female NPT
Model 600HT For high temperature application not to exceed
210°F
Model 600CH Chrome internals for harsh water conditions
Model 600LPV Same as 600HT except spring range is
10 – 35 psi, factory set at 20 psi
Model 600LPC Spring range is 10 to 35 psi, factory set at
20 psi (2” must be field set only)
Model 610 Same as 600HR except rated for 400 psi and
spring range is 75 – 125 psi, factory set at 85 psi
Model 600SC Sealed cage bell and stainless steel adjusting
screw. For below-ground and indoor
applications
Model 600DM Double male meter thread, no union included
(1” National Hose Thread, fits 5/8” x 3/4” and
3/4” water meter)
Model 600XL California AB 1953 compliant
For Additional Information, including flow curves, reference
WK-RC catalog or visit our web site.
OptionsTypical InstallationX Ref Features Applications
Many water pressure reduction applications involve water that has a high concentration of sand. Sandy
water results in frequent integral strainer cleaning. The model 600 is just the regulator for these applica-
tions. The model 600 has its strainer accessible through a separate cap. Unlike other regulator designs
that require disassembly of the valve, the model 600’s screen is accessed by the removal of a single cap.
This will drastically reduce the time needed to clean the strainer screen. Just like the 500 series, the 600
is also equipped with a union inlet connection and a female NPT outlet connection.
Local codes shall govern installation requirements. Unless otherwise specified, the assembly shall be mounted in accordance with the latest edition of
the Uniform Plumbing Code. The Model 600 may be installed in any position. If installed in a pit, vault or indoors, specify the “SC” sealed cage option.
Multiple installations are recommend for wide demand variations or where the desired pressure reduction is more than 4 to 1 (i.e.: 200 psi inlet reduced
to 50 psi outlet). CAUTION: Anytime a reducing valve is adjusted, a pressure gauge (Model HGI-25) must be used downstream to verify correct pressure
setting. Do not bottom out adjustment bolt on bell housing.
600 Series
NOITALLATSNI LACITREVNOITALLATSNI ROODTUO
PROTECTIVE
ENCLOSURE
DIRECTION OF FLOW
12" MIN.
30" MAX.
MODEL 975XL
MODEL
600
MODEL
600
BACKFLOW PREVENTER
OPTIONAL PRESSURE GAUGE
MODEL 92
DIRECTION OF FLOW
OPTIONAL PRESSURE
GAUGE
MODEL 92
SHUT-OFF
WILKINS WATTS CASH-ACME
600 U5B, 25AUB EB-24U
600L U5 E-3
Accessories
 Pressure gauges (Model 92-25A 1/2", 3/4") (Model 92-25 1" – 2")
Water Pressure Reducing Valves