LED‐GF25 User Manual Please read the instruction carefully before use
CONTENTS 1. Safety Instructions....................................................................................................2 2. Technical Specifications ............................................................................................3 3. How To Set The Unit .................................................................................................4 3.1 Rear Panel...........................................................................................................4 3.
1. Safety Instructions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING y Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. y Unpack and check carefully there is no transportation damage before using the unit. y Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
Caution: There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. Installation: The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating.
y Weight: 3.7kgs y Dimension: 395 x240 x193mm 3. How To Set The Unit 3.1 Rear Panel 1. POWER OUT: Used to connect to next unit 2.
3. LED: DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Flashing Sound activation 4. Button: MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions 5. Function Display: Used to show the various menus and the selected functions. 6. DMX IN: For DMX512 link, use 3‐pin XLR plug cable to connect to the DMX controller and input the DMX signal; 7.
DMX 512 ADDRESS To select the , press the ENTER button to show the DMX ADDRESS on the display. Use the DOWN/UP button to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
SLAVE MODE To select the , press the ENTER button to show the SLAVE MODE on the display. Use the DOWN/UP button to select the (MASTER), (SLAVE 1, normal) or (SLAVE 2, 2 light show) modes. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
LED DISPLAY To select the , press the ENTER button to show the BALCKOUT MODE on the display. Use the DOWN/UP button to select the (LED display on) or (LED display off) mode. Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
SOFTWARE VERSION , press the ENTER button to show the SOFTWARE VERSION on the display and To select the the display will show the version of software of the unit . To go back to the functions without any changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to exit the menu mode. RESET , press the ENTER button to show the RESET on the display. Press the ENTER To select the button and all channels of the unit will return to their standard position. 4.
2‐light show In slave mode, means the unit works as the master unit and means 2‐light show. on the second unit to get contrast In order to create a great light show, you can set movement to each other, even if you have two units only. 4.2 Easy Controller The easy remote control is used only in master/slave mode.
5.
6. DMX Connection Unit 1 Unit 2 Unit 3 Unit 4 1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system 2. The DMX output and input connectors are pass‐through to maintain the DMX circuit when one of the units’ power is disconnected. 3.
7. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3.
8. Fixture Cleaning The cleaning must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 30 days.
Innovation, Quality, Performance 15A
