Manual for Acer Projector XD1170/XD1270/XD1280 series Downloaded From projector-manual.
Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it. USA For electronic products containing an LCD/CRT monitor or display, or a super high pressure mercury lamp: Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae.org.
Table of Contents Table of Contents.......................................................................................... 1 Usage Notice................................................................................................. 2 Precautions...........................................................................................................2 Introduction................................................................................................... 4 Product Features.....................
Usage Notice Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. WarningWarningWarningWarningWarning- Warning- Warning- WarningWarningWarning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Please do not open or disassemble the product as this may cause electric shock.
Usage Notice Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: - In extremely hot, cold or humid environments.
Introduction Product Features This product is a SVGA (XD1170) / XGA (XD1270, XD1280) single chip 0.55” DLPTM projector. Outstanding features include: u True SVGA, 800 x 600 addressable pixels (for XD1170 series only) True XGA, 1024 x 768 addressable pixels (for XD1270, XD1280 series only) u Single chip DLPTM technology u NTSC3.58/NTSC4.
Introduction Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. Projector with lens cap Power Cord 1.8m VGA Cable 1.8m Composite Video Cable 1.8m USB Cable 2.0m S-Video Cable 2.0m Audio Cable Jack /Jack 2.0m VGA to Component/ HDTV Adapter Remote Control 2 x Battery Carrying Case User’s Guide Quick Start Card ... English Downloaded From projector-manual.
Introduction Product Overview Main Unit 1 2 4 3 7 4 5 6 8 1. 2. 3. 4. 5. 6. 7. 8. 9. Focus Ring Zoom Ring Zoom Lens Remote Control Receiver Elevator Button Elevator Foot Power Socket Connection Ports Control Panel English ... Downloaded From projector-manual.
Introduction Control Panel 5 4 6 3 7 2 1. 2. 3. 4. 5. 6. 7. 1 Temp Indicator LED Lamp Indicator LED Power and Indicator LED (Power LED) Source Resync Four Directional Select Keys Menu ... English Downloaded From projector-manual.
Introduction Connection Ports 1 2 3 4 5 6 7 For XD1 1 7 0 / XD1270 only 10 8 1. 9 DVI Input Connector (for Digital signal with HDCP function) (Optional) 2. PC Analog Signal/HDTV/Component Video Input Connector 3. Audio Input Connector 4. S-Video Input Connector 5. Monitor Loop-through Output Connector (VGA-Out) 6. USB Connector 7. RS232 Connector 8. KensingtonTM Lock Port 9. Composite Video Input Connector 10. 5V DC Output Jack (for attached dongle device) (for XD1170/XD1270 only) English ...
Introduction Remote Control with Laser Pointer 1 24 2 25 3 4 5 6 7 8 9 10 11 12 26 27 13 14 16 15 17 18 19 20 21 22 23 for XD1170/Japan models series 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Laser Pointer Power Resync Source Freeze Hide Aspect Ratio Mute Keystone/Four Directional Select Keys Back Menu Digital Zoom Empowering Key Volume + Downloaded From projector-manual.com Acer Manuals 28 29 for XD1270/XD1280 series 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.
Installation Connecting the Projector 1 USB 5 DVI for XD1170/ XD1270 only 7 VGA 2 RS232 3 9 10 DVD Player, Settop Box, HDTV receiver 6 8 4 Video Output S-Video Output 1...................................................................................................... Power Cord 2..................................................................... DVI Cable (Optional Function) 3.......................................................................................................
Installation Powering On/Off the Projector Powering On the Projector 1. Remove the lens cap. 2. Ensure that the power cord and signal cable are securely connected. The Power LED will flash red. 3. Turn on the lamp by pressing “Power” button on the control panel.And the Power LED will turn blue. 4. Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically. v If the screen displays “No Signal”, please make sure the signal cables are securely connected.
Installation Powering off the projector 1. Press the “Power” button to turn off the projector lamp, you will see a message “Please press power button again to complete the shutdown process. Warning: DO NOT unplug while the projector fan is still running.” displayed on the projector’s screen. Press the “Power” button again to confirm, otherwise the message will disappear after 5 seconds. 2. The cooling fans continue to operate for about 30 seconds for cooling cycle and the Power LED will be quick red flash.
Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. Press the elevator button . 2. Raise the image to the desired height angle , then release the button to lock the elevator foot into position. 3. Use to fine-tune the display angle. To lower the image: 1. Press the elevator button. 2. Lower the image, then release the button to lock the elevator foot into position. 3.
Installation Adjusting the Projector Zoom / Focus You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 4.9 to 39.4 feet (1.5 to 12.0 meters). Zoom Ring Focus Ring Adjusting Projection Image Size 304.9" (774.5cm) 277.3" (704.4cm) 203.3" (516.3cm) 184.9" (469.6cm) 177.9" (451.8cm) 161.8" (410.9cm) 127.1" (322.7cm) 115.6" (293.5cm) 76.2" (193.6cm) 69.3" (176.1cm) 38.1" (96.8cm) 34.7" (88.1cm) 4.
User Controls Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Power Refer to the “Power On/Off the Projector” section on pages 11, 12. Resync Automatically synchronizes the projector to the input source. Source Press “Source” to choose RGB, Component-p, Component-i, S-Video, Composite, DVI-D (Optional), Video and HDTV sources.
User Controls Using the Remote Control Power Refer to the “Power On/Off the Projector” section on pages 11, 12. Laser Button (for XD1270/XD1280 series only) Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Resync Automatically synchronizes the projector to the input source. Source Press “Source” to choose RGB, Component-p, Component-i, S-Video, Composite Video, DVI-D (Optional) and HDTV sources. Freeze Press “Freeze” to pause the screen image.
User Controls Mouse / Mouse Right Click / Mouse Left Click These functions are the same as a mouse of PC or Mac. Empowering Key Acer Empowering Key provides three Acer unique functions, they are "Acer eView Management", "Acer eTimer Management" and "Acer eOpening Management" respectively. Press "e" key for more than one second to launch the on screen display main menu to modify its function. Acer eView Management Press "e" to launch “Acer eView Management” submenu.
User Controls VGA 4Press “VGA” to change source to VGA-In connector. This con- nector supports Analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync. Video 4Press “Video” to change source to Composite Video source. Component 4Press “Component” to change source to component connec tor. This connector supports YPbPr (480p/576p/720p/1080i) and YCbCr (480i/576i) DVI 4Press “DVI” to change source to DVI connector.
User Controls On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press “Menu” on the Remote Control or Control Panel. 2. When OSD is displayed, use keys to select any item in the main menu. After selecting the desired main menu item, press 3. Use to enter sub menu for feature setting.
User Controls Color (Computer / Video Mode) Display Mode There are many factory presets optimized for various types of images. Bright : For brightness optimization. PC : For computer or notebook. Video : For playing video in a bright environment. Theater : For Home Theatre usage in a dark room. sRGB : For true-color optimization. User : Memorize user’s settings. Brightness Adjust the brightness of the image. Press the Press the Contrast to darken image. to lighten the image.
User Controls Color (Computer / Video Mode) White Segment Use the white Segment control to set the white peaking level of DMD chip. 0 stands for minimal segment, and 10 stands for maximum segment. If you prefer a stronger image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Degamma Effects the represent of dark scenery. With greater gamma value, dark scenery will look brighter. Color R Adjusts the red color.
User Controls Image (Computer / Video Mode) Keystone Adjust image distortion caused by tilting projection. (±16 degrees) Aspect Ratio Use this function to choose your desired aspect ratio. Auto : Keep the image with original width-higth ratio and maxi mize the image to fit native horizontal or vertical pixels. 4:3 : The input source will be scaled to fit the projection screen and becomes 4:3 ratio.
User Controls Image (Computer / Video Mode) H. Position (Horizontal Position) Press the Press the to move the image left. to move the image right. V. Position (Vertical Position) “H. Position”, “V. Position”, “Frequency” and “ Tracking” functions are not supported under DVI and Video mode. Press the to move the image down. Press the to move the image up. Frequency “Frequency”changes the display data frequency to match the frequency of your computer’s graphic card.
User Controls Management (Computer / Video Mode) ECO Mode Choose “On” to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose ”Off” to return normal mode. Auto Shutdown(Minutes) The projector will auto shutdown while there is no signal input after the setting time. Source Lock When source lock is turned off, the projector will search for other signals if the current input signal is lost.
User Controls Management (Computer / Video Mode) Acer eOpening Management is a PC utility for user to change the default startup screen of Acer projector to their desired image. You can install Acer eOpening Management from the bundled CD. Connect the projector to your PC with the bundled USB cable then execute Acer eOpening Management utility to download your desired image from your PC to projector. Before the download starts, the projector must enter “Download Mode” first.
User Controls Management (Computer / Video Mode) Lamp Hour Reset Press the button after choosing “Yes ”to turn the lamp hour counter to 0 hours. Security Press to start “Security” setting. If the “Security” function is enabled, your must enter “Administrator Password” first before Security setting. Security This projector provides an excellent security function for the administrator to manage the usage of the projector. Select “On” to enable the security function.
User Controls Management (Computer / Video Mode) Timeout(Min.) Once “Security” is set to “On”, administrator can set timeout function. Press or to select timeout duration. The range is from 10 minute to 990 minutes. When time is up, the projector will request user to enter password again. The factory default setting of “Timeout(Min.)” is “Off”. User Password Press to set up or change “User Password”. Use , , or to select the character and press “MENU” to confirm.
User Controls Management (Computer / Video Mode) The projector provide two options of "Security Mode". Select “Request password only after plugging power cord”, the project will request user to input password only for the first time plugging on power cord of the projector. Select “Always request password while projector turns on”, user have to input password every time when switching on the projector.
User Controls Management (Computer / Video Mode) If administrator forgot “Administrator Password”, do the following to retrieve the “Administrator Password”: 1. Press “MENU” for more than 4 seconds when any of “Enter Password” or “Enter Administrator Password” dialogue is currently displayed. 2. Write down the “Unlock ID” and contact with Acer service center. They will give you new Administrator Password according to the Unlock ID. 3.
User Controls Audio (Computer / Video Mode) Volume Press the Press the Mute to decrease the volume. to increase the volume. Choose the “On” to turn mute on. Choose the “Off” to turn mute off. Power On/Off Volume Choose this function to adjust volume when power on/off. Alarm Volume Choose this function to adjust volume when there are errors of the projector. English ... 30 Downloaded From projector-manual.
User Controls Timer (Computer / Video Mode) Timer Start Press the to start/stop timer. Timer Period Press the to adjust timer period. Timer Volume Choose this function to adjust volume when timer function is enable and time is up. Timer Display Press the to choose timer display mode on the screen. Timer Location Choose the timer location on the screen. 31 ... English Downloaded From projector-manual.
User Controls Language (Computer / Video Mode) Language Choose the multilingual OSD menu .Use the your preferred language. Press to confirm the selection. English ... 32 Downloaded From projector-manual.
Appendices Troubleshooting If you experience trouble with the projector, refer to the following information. If the problem persists, please contact your local reseller or service center. Problem: No image appears on screen. Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure the pins of connectors are not crooked or broken. Check if the projection lamp has been securely installed.
Appendices 4. Follow the above steps 1-2. Click on the “Advanced Properties” button. 5. Select the “Change” button under the “Monitor” tab. 6. Click on “Show all devices”. Then select “Standard monitor types” under the “Manufacturers” box ; choose the resolution mode you need under the “Models” box. 7. Verify that the resolution setting of the monitor display is less than or equal to 800 x 600. If you are using a Notebook PC: 1.
Appendices Problem: The image is outstretched when displaying 16:9 DVD. The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. If the image is still outstretched, you will also need to adjust the aspect ratio by referring to the following: Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD.
Appendices Problem: Message Reminders “Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!” will be shown about 10 seconds when lamp life is going to deplete. “Projector Overheated. Lamp will automatically turn off soon.” will be shown when the system temperature is over heat. “Fan fail. Lamp will automatically turn off soon.” will be shown when the fan is out of order. English ... 36 Downloaded From projector-manual.
Appendices Replacing the lamp Warning: Lamp compartment is hot! Allow it to cool down before changing lamp! The projector will detect the lamp life itself. It will show you a warning message “Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!” When you see this message, changing the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Appendices Specifications The specs specified below are subject to change without notice. Regarding the final specs, please refer to Acer accounced marketing specs. Light Valve - Single Chip DLPTM Technology by Texas Instruments Lamp - 200W User Replaceable Lamp (for XD1170/XD1270 series) - 230W User Replaceable Lamp (for XD1280 series) Number of Pixels - 800 pixels(H) X 600 lines(V) (for XD1170 series only) - 1024 pixels(H) X 768 lines(V) (for XD1270/XD1280 series) Displayable Color - 16.
Appendices I/O Connectors - Power: AC power input socket - VGA Input: One DVI connector for Digital signal with HDCP (for XD1170D/XD1270D/XD1280D only) One 15-pin D-sub for VGA, component and HDTV signal - VGA Output: One 15-pin D-sub for VGA output - Video Input: One Composite video RCA input One S-Video input - One 5V DC output jack for attached dongle device (for XD1170/XD1270 only) - RS232 connector - USB: One USB connector - Audio Input: One phone jack for audio input Weight - 4.
Appendices Compatibility Modes Mode Resolution VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA XGA VESA XGA VESA XGA VESA XGA VESA SXGA VESA SXGA VESA SXGA MAC LC 13” MAC II 13” MAC 16” MAC 19” MAC MAC G4 i MAC DV i MAC DV 640 x 350 640 x 350 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 720 x 400 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 8
Appendices Regulation & Safety Notices This appendix lists the general notices of your Acer Projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, in cluding interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003.
Appendices Important safety instructions Read these instructions carefully. Save them for future reference. 1. Follow all warnings and instructions marked on the product. 2. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a water-moistened cloth for cleaning. 3. Do not use this product near water. 4. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged. 5.
Appendices Radio device regulatory notice NOTE: Below regulatory information is for models with wireless LAN only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Below information is for products with such devices.
Appendices The FCC RF safety requirement The radiated output power of the wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the Acer used in such a manner that the potential for human contact during normal operation shall be Acer projector is minimized as follows: • An improper installation or unauthorized use may cause harmful interference to radio communications. Also any tampering of theinternal antenna will void the FCC certification and your warranty.
