User Guide

ManualsBrandsAcer ManualsOtherAM501

TABLE OF CONTENTS

TABLE OF CONTENTS ........................................................................... 1

IMPORTANT SAFETY INSTRUCTIONS ................................................. 2

FEDERAL COMMUNICATIONS COMMISSION...................................... 3

CONNECTING THE MONITOR AND SWIVEL BASE............................. 4

REMOVING THE MONITOR AND SWIVEL BASE.................................. 4

INTRODUCTION....................................................................................... 5

INSTALLATION........................................................................................ 6

USER CONTROLS................................................................................... 7

LED ICON SUMMARY ............................................................................. 9

SPECIFICATIONS .................................................................................. 10

TROUBLESHOOTING............................................................................ 11

Summary of content (12 pages)

PAGE 1
TABLE OF CONTENTS TABLE OF CONTENTS ........................................................................... 1 IMPORTANT SAFETY INSTRUCTIONS ................................................. 2 FEDERAL COMMUNICATIONS COMMISSION...................................... 3 CONNECTING THE MONITOR AND SWIVEL BASE ............................. 4 REMOVING THE MONITOR AND SWIVEL BASE.................................. 4 INTRODUCTION......................................................................................
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS 1. Please read these instructions thoroughly. 2. Please keep this guide for future use. 3. Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol sprays to clean this device. Use a clean dampened cloth in stead. 4. To avoid damaging the device, only use factory-approved accessories. 5. Protect the device against moisture. 6. In order to set up the device, first place it on a stable surface. Tipping it over or dropping can 7.
PAGE 3
FEDERAL COMMUNICATIONS COMMISSION ( FCC Statement ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
CONNECTING THE MONITOR AND SWIVEL BASE 1. Place the monitor with its tube down on a stable surface. 2. Align the four tabs of the swivel base with the slots in the bottom of the monitor. 3. Insert the tabs into the slots of the monitor 4. Now slowly slide the swivel base toward the front of the monitor till you hear the spring lock click into place. REMOVING THE MONITOR AND SWIVEL BASE If you need to remove the swivel base, push the spring lock and then pull the swivel base away from the monitor.
PAGE 5
INTRODUCTION Congratulations on your purchase of this new high performance 15˝ Monitor. Using state-of-the-art electronics, this monitor supports a 1024 X 768 resolution. The on-screen display allows you to customize the display settings to suit your individual taste. Features 15-inch monitor with a large, viewable screen for comfortable viewing. Digital controls for easy and accurate adjustment of the screen image. Energy Star compliant for reduced power consumption.
PAGE 6
INSTALLATION 1. Connect the monitor signal cable 1 to the 15-pin mini D-sub (VGA) on the back of the computer. 2. Connect the power cord to the power connector on the back panel of the monitor, then plug the other end into an electrical outlet that is easily accessible, and close to the monitor. 3. First turn on the power of the computer, then that of the monitor. 4. Adjust the tilt of the swivel base for maximum viewing comfort. The installation of your monitor is now complete.
PAGE 7
USER CONTROLS 1 Power Switch Turns the monitor on and off 2 Power LED Indicator Green States Status Light On Flash Sleep 7
PAGE 8
3 4 Reset Adjustments For adjusting the display in the selected function. Resets default values. 5 Select button 6 Function LED Indicator For selecting functions. 1) When the highest or lowest possible setting for a particular display control has been reached, its corresponding LED will flash. 2) When the 2nd LED’s light is on, follow the 2nd function’s indication. 3) When the input timing is not the preset timing, the recall function will not function.
PAGE 9
LED ICON SUMMARY Icon Function Function Description Brightness Adjusts display brightness Contrast Adjusts display contrast H. Size Increases and decreases screen width H. Position V. Size Shifts display image right or left Increase and decrease screen height V.
PAGE 10
SPECIFICATIONS Screen Size Dot Pitch (mm) Surface Viewable Image Area (mm) Input Signal Video Sync. Scanning Frequency Horizontal (KHz) Vertical (Hz) Max Resolution 15″ CRT 0.28 Non –glare 260 x 195 RGB Analog 0.7Vp-p/75Ohm a.
PAGE 11
TROUBLESHOOTING Please refer to the following solutions for the failure symptoms that occur the most frequent. If the symptom remains after trying these suggested solutions, please contact your local authorized service center. Problem: Power LED is not lit when monitor is powered on. Check to make sure that the power cord is connected properly. Make sure that the extension cord or the surge protector is turned on if the monitor is plugged into a power extension cord or a surge protector.
PAGE 12