TravelMate 6592/6592G Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on TravelMate 6592/6592G service guide.
Copyright Copyright © 2007 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: 4 SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
Table of Contents Chapter 1 System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Mainboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Top View ...........................................................................
Removing the Battery Pack ................................................................................61 Removing the Cover Securing Screws and Covers ............................................61 Removing the HDD .............................................................................................62 Removing the Memory Module ...........................................................................63 Removing the Wireless Card .................................................................
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Undetermined Problems . . . . . . . . . . . . . . . .
4
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many feature: Operating system q Genuine Windows® VistaTM Capable q Genuine Windows® XP Home Edition (Service Pack 2) q Genuine Windows® XP Media Center Edition 2005 (Rollup 2) NOTE: Windows® VistaTM Capable PCs come with Windows® XP installed, and can be upgraded to Windows® VistaTM. For more information on Windows® VistaTM and how to upgrade, go to: Microsoft.com/windowsvista.
q Acer ArcadeTM featuring Acer CinemaVisionTM and Acer ClearVision technologies q Acer TV-tunver options: TV-tuner •Analog TV-tuner supporting hardware MPEG-2 stream encding •Digital and analog hybrid TV-tuner supporting hardware MPEG-2 stream encoding •Digital and analog hybrid TV-tuner supporting software MPEG-2 stream encoding q Analog TV-tuner supporting international analog TV standards (NTSC/PAL/SECAM) q Digital TV-tuner supporting DVB-T (Digital Video Broadcasting Terrestrial) standard (
q Modem: 56K ITU V.92 modem with PTT approval; wake-on ring ready q LAN: gigabit Ethernet; wake-on-LAN ready q WPAN: Bluetooth® 1.1 @ 723 bps q Optional WLAN:ICH6-M (dual-band tri-mode 802.11a/b/g) Wi-Fi® CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology q CRT port --- Suport CRT monitor. q 3 * USB 2.0/1.
System Block Diagram 4 Chapter 1
Mainboard Layout Top View 1 JACK1 AV-in Jack 20 CN29 PATA HDD Connector 2 CN1 TV Antenna Connector 21 CN30 SATA HDD Connector 3 CN2 S-Video Connector 22 U23 North Bridge 4 CN509 Card Bus Socket 23 U33 RAID Controller 5 CN3 S-Video Connector 24 U37 Timing Controller 6 CN4 HDMI Connector 25 CN13 CPU Socket 7 U6 Video Memory 26 CN28 SATA HDD Connector 8 CN5 I/O Board to Main Board Connector 27 CN24 BIOS Flash Memory 9 U7 Video Memory 28 U515 Audio Codec 10
17 CN14 DIMM Socket 36 CN11 IEEE port 18 CN18 Optical Disk Drive Connector 37 U25 PCI cardbus/Media Board/1394 IC 19 U39 South Bridge Bottom View 6 1 U504 LAN Transformer GSN 5009 9 CN4000 Touchpad Connector (Touchpad to main board) 2 CN502 Launch Board Connector 10 CN4001 6-pin Touchpad Board Connector 3 U503 Video Memory 11 CN504 Audio Board Connector 4 U502 Video Memory 12 CN506 DDR2 SDRAM IC 5 CN4002 LCD Connector 13 CN5001 Hotkey Board Connector 6 CN3000
Your Acer Notebook Tour After knowing your computer features, let us show you around your new TravelMate 6592/6592G computer. Front View # Item Description 1 Built-in camera 1.3 megapixel web camera for video communication. 2 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 3 Media/volume buttons For use with Acer Arcade and other mdeia playing programs. 4/8 Chapter 1 Icon Microphone Internal microphone for sound recording.
10/11 12 Easy-launch buttons Buttons for launching frequently used programs. Power button Turns the computer on and off. Closed Front View # 8 Icon Item Description 1 Speaker Left and right speakers deliver stereo audio output. 2 Infrared port/CIR receiver Interfaces with infrared devices (e.g, infrared printer and IR-aware computer)/ Receives signals from a remote control. 3 Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).
Left View # Icon Item Description 1 USB 2.0 ports Connects to USB 2.0 devices (e.g., USB mouse, USB camera). 2 Modem (RJ-11) port Connects to a phone line. 3 Optical drive Internal optical drive; accepts CDs or DVDs (slot-load or tray-load depending on model). 4 Optical disk access indicator Lights up when the optical drive is active. 5 Optical drive eject button Ejects the optical disk from the drive.
3 3 USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB camera). 4 4-pin IEEE 1394 port Connects to IEEE 1394 devices. 5 PC Card slot eject button Ejects the PC Card from the slot. 6 PC Card slot Accepts one Type II PC Card. 7 Express Card/54 slot Accepts and ExpressCard/34 module Note: ExpressCards are third generation of PC cards, hot-swapable and smaller than previous PC Cards. Designed for both desktop and mobile use, ExpressCards use either USB 2.
# Icon Item Description 5 Ventilation slots Enable the computer to stay cool, even after prolonged use. 6 S-video/TV-out (NTSC/PAL) port Connects to a television or display device with S-video input. 7 External display (VGA) port Connects to a display device (e.g., external monitor, LCD projector). 8 DVI-D port Supports digital video connections. 9 Ethernet (RJ-45) Connects to an Ethernet 10/100/1000based network (for selected models). 10 Parallel port Connects to a printer.
2 Memory compartment Houses the computer’s main memory. 3 Battery lock Locks the battery in position. 4 Battery release latch Releases the battery for removal. 5 Battery bay Houses the computer’s battery pack. 6 Hard disk bay Houses the computer’s hard disk (secured with screws) 7 Sub woofer Emits low frequency sound output. Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed up.
Icon Function Description Battery Lights up when the battery is being charged. Bluetooth Indicates the status of Bluetooth communication. Wireless LAN Indicates the status of wireless LAN communication. NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode. Easy-Launch Buttons Located above the keyboard are four buttons. These buttons are called easy-launch buttons.
Touchpad Basics The following teaches you how to use the touchpad: q Move your finger across the touchpad (2) to move the cursor. q Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad is the same as clicking the left button. q Use the 4-way scroll (3) button to scroll up or down and move left or right a page.
Using the Keyboard The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. y y y gg Lock Key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num lock + When Num Lock is on, the embedded keypad is in numeric mode.
Key Icon Windows key Description Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of function: + Activates next taskbar button. + Opens the My Computer window + Opens Help and Support. + Opens the Find: All Files dialog box. + Opens the Run dialog box. + M Minimizes all windows. + action.
Hot Key Icon Function Description + Sleep Puts the computer in Sleep mode. + Display toggle Switches display output between the display screen, external monitor (if connected) and both. + Screen blank Turns the display screen backlight off to save power. Press any key to return. + Touchpad toggle Turns the internal touchpad on and off. + Speaker toggle Turns the speakers on and off. + Volume up Increases the speaker volume.
2. Either directly press the < > symbol at the bottom-right of the keyboard, or hold and then press the<5> symbol at the upper-center of the keyboard. NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information. The US dollar sign 1. Open a text editor or word processor. 2.
Acer Empowering Technology Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and manage your new Acer notebook. It features the following handy utilities: q q q q q q q Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms. Acer eLock Management limits access to external storage media. Acer ePerformance Management improves system performance by optimizing disk space, memory and registry settings.
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft Outlook. There are two passwords that can be used to encrypt/decrypt a file; the supervisor passowrd and the filespecific password. The supervisor passwork is a “master” password that cna decrypt any file on your system; the file-specific password will be used to encrypt files by default, or you cna choose to enter your own filespecific password when encrypting a file.
Acer eLock Management Acer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy drives to ensure that data can’t be stolen while your notebook is unattended. q q q Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives, USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be mounted as a file system when plugged into the system.
Acer ePerformance Management Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer notebook. It provides you with the following options to enhance overall system performance: q q q 22 Memory optimization - releases unused memory and check usage. Disk optimization - removes unneeded items and files. Speed optimization - improves the usability and performance of your Windows XP system.
Acer eRecovery Management Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by the manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you with: q q q Password protection. Recovery of applications and drivers. Image/data backup: q q Back up to HDD (set recovery point). q Back up to CD/DVD.
NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To ensure the best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
Acer ePower Management Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower Management from the Empowering Technology interface, or double-click the Acer ePower Management icon in the task tray. Acer Mode The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other settings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, Memory Card, Audio, and Wired LAN.
You can also click “Advanced Settings” to: q q q q 26 Set alarms. Re-load factory defaults. Select what actions will be taken when the cover is closed, and set passwords for accessing the system after Hibernation or Standby. View information about Acer ePower Management.
Acer ePresentation Management Acer ePresentation Management lets you select from two of the most common projector resolutions: XGA and SVGA.
Acer OrbiCam The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at the back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that you can transmit the best video quality over an instant Messenger service. Getting to know your Acer OrbiCam 1 No.
Changing the Acer OrbiCam settings Resolution To change the capture resolution, click the displayed resolution at the bottom right corner of the capture window, then select the desired resolution. Options Click Options to display the Window, Preview, and Folder tabs. Use the options to change the capture window size, preview settings, and the folder for captured photos or videos.
q Capture settings: From the Camera Settings window, click the Driver Settings button. The Properties window will appear. q Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness, etc. q Advanced Settings allows you to achieve gain control, implement image mirror, select image enhancements and anti-flicker settings, and turn on/off the camera indicator.
The VisageON window appears as below: 2. Select and apply a video effect in the left section of the VisageON window. Change the face tracking settings and options in the right section. Using the face tracking feature To use the face tracking feature: 1. Click the left icon down arrow button, then select Single User or Multiple Users from the pop-up menu.
Using video effects (selected models only) The Video Settings section allows you to select an avatar or accessory video effect from the list. To select an effect: 1. Click the encircled icon to display the available video effects. The Video Effect Selection window appears as below: 2. Click on a video effect to use. The selected effect appears in the video effects section of the VisageON window. NOTE: When using avatars, you may have to calibrate the face points to achieve better tracking.
Using the System Utilities NOTE: The system utilities work under Microsoft Windows XP only. Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value. Launch Manager Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access the Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
Hardware Specifications and Configurations Processor Item Specification CPU type Intel® Pentium MHz FSB) ® M 725/730 Processor (2 MB L2 cache, 1.6GHz, 400/533 Intel® Celeron M 370/380/390 Processor (1 MB L2 cache, 1.50/1.60/ 1.70GHz, 400MHz FSB) Core logic Intel® 910GML+ICH6M CPU package Intel socketable 478pin Micro-BGA CPU core voltage 0.944~1.
System Memory Item Specification Memory controller Built-in Intel 910GML Memory size 0MB (no on-board memory) ® DIMM socket number 2 sockets Supports memory size per socket 1024MB Supports maximum memory size 2G (by two 1024MB SO-DIMM module) Supports DIMM type DDR 2 Synchronous DRAM Supports DIMM Speed 400 MHz Supports DIMM voltage 1.8V and 0.
LAN Interface Item Features Specification Integrated 10/100 BASE-T transceiver Wake on LAN support compliant with ACPI 2.0 PCI v2.2 Modem Interface Item Specification Data modem data baud rate (bps) 56K Supports modem protocol V.92 Modem connector type RJ11 Modem connector location Right side Bluetooth Interface Item Chipset Specification Built-in ICH6-M Data throughput 723 bps (full speed data rate) Protocol Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified).
Hard Disk Drive Interface Item Interface ATA/ATAPI-6; ATA-6 ATA/ATAPI-6; ATA-6 ATA/ATA-6; ATA-6 Max. media transfer rate (disk-buffer, Mbytes/s) 372 350 350 Data transfer rate (host~buffer, Mbytes/s) 100 MB/Sec. Ultra DMA mode-5 100 MB/Sec. Ultra DMA mode-5 100 MB/Sec.
DVD-Dual Interface Item Specification Applicable disc format Support disc formats 1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD, CD-Extra and CD-Text 2. Reads data in Photo CD (single and Multi-session) 3. Reads standard CD-DA 4. Reads and writes CD-R discs 5. Reads and writes CD-RW discs 6. Reads and writes in each dVD+R/RW (Ver. 1.1) 7. Reads data in each DVD-ROM and DVD-R (Ver. 2.0 for Authoring) 8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVD-RW and DVD+R/RW (Ver1.
USB Port Item Specification Chipset Built-in ICH6-M USB Compliancy Level 2.0 OHCI USB 1.1 and USB 2.
Battery Item Specification Vendor & model name Sanyo (6cell) 2.0 Sony (6cell) 2.0 Panasonic (6cell) 2.0 Snayo (6cell) 2.4 Sony (6cell) 2.4 Panasonic (6cell)2.4 Sanyo (9cell) 2.4 Battery Type Li-ion Pack capacity 4000 mAH forSanyo (6cell) 2.0 3920 mAH Sony (6cell) 2.0 3900 mAH Panasonic (6cell) 2.0 4800 mAH Snayo (6cell) 2.4 4800 mAH Sony (6cell) 2.4 4800 mAH Panasonic (6cell)2.4 Sanyo (9cell) 2.
LCD 14.1 inch Item Specification Viewing Angle (degree) Horizontal: Right/Left 40/40 45/45 40/40 Vertial: Upper/Lower 10/30 15/35 20/40 Operating 0 to +50 0 to +50 0 to +50 Storage (shipping) -20 to +60 -25 to +60 -20 to +60 Temperature Range(°C) LCD Inverter Item Specification Vendor & model name Darfon/V189-301GP Brightness conditions N/A Input voltage (V) 9~21 Input current (mA) 2.56 (max) Output voltage (V, rms) 780V (2000V for kick off) Output current (mA, rms) 6.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Navigating the BIOS Utility There are six menu options: Info., Main, System Devices, Security, Boot, and Exit. Follow these instructions: q To choose a menu, use the cursor left/right keys (zx). q To choose a parameter, use the cursor up/down keys ( wy). q To change the value of a parameter, press por q. q A plus sign (+) indicates the item has sub-items. Press e to expand this item. q Press ^ while you are in any of the menu options to go to the Exit menu.
Information NOTE: The following system information is subject change between models and is for reference only. Phoenix TrustedCore Setup Utility Information CPU Type: Genuine Intel ® CPU CPU Speed: XXXXGHz Help Item Menu Level IDE0 Model Name: Intel Raid0 IDE0 Serial Number: TSST CorpCD IDE1 Model Name: MK3018GAP-(PM) IDE1 Serial Number: Y2554027T ATAPI Model Name Slimtype DVD-ROM LSD-081-(S System BIOS Version V1.0 VGA BIOS Version ATI M9+XC V0.
Main The Main screen displays a summary of your computer hardware information, and also includes basic setup parameters. It allows the user to specify standard IBM PC AT system parameters. NOTE: The screen below is for reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Format/Option System Time Sets the system time. The hours are displayed with 24-hour format Format: HH:MM:SS (hour:minute:second) System Date Sets the system date Format MM/DD/YYYY (month/day/year) System Memory This field reports the memory size of the system.
Advanced The Advanced screen displays advanced settings in BIOS.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Option Supervisor Password Is Shows the setting for the Supervisor password Clear or Set User Password Is Shows the setting for the user password Clear or Set HDD Passwored Is Shows the setting for the HDD password Clear or Set Set Supervisor Password Press Enter to set the supervisor password.
Symbol Character Symbol Name / Slash \ Back-slash q q q The maximum cycles to retry password is limited to 3. User cannot change/remove password during resuming from S4. Finger print: support 10 fingers - Upack/Authentec modules. Setting a Password Perform the following steps to set the supervisor, user, or HDD password. NOTE: The following example uses the Supervisor Password screens. The User and HDD Password screens are identical. 1.
Changing a Password 1. Use the µ and ¶ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears: 2. Type the current password in the Enter Current Password field and press Enter. 3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. 4. Press Enter. After setting the password, the computer sets the Supervisor Password Is parameter to Set. 5.
Chapter 2 53
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Exit The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use. Phoenix - Award WorkstationBIOS CMOS Setup Utility Exit Exit Saving Changes Help Item Exit Discarding Changes Load Setup Defaults Menu Level X Discard Changes Save Changes KLIJ :Move Enter: Select +/-/PU/PD :Value F10: Save and Exit ESC:Exit F1: General Help F5: Previous Values F7: Optimized Defaults The table below describes the parameters in this screen.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: q New versions of system programs q New features or options q Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: q Wrist grounding strap and conductive mat for preventing electrostatic discharge q Small Philips screw driver q Philips screwdriver q Plastic flat head screw driver q Tweezers NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 58 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system.
Disassembly Procedure Flowcharts The following flowcharts give you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
LCM Module Disassembly Flowchart 60 Chapter 3
Main Unit Disassembly Procedure Removing the Battery Pack 1. Turn the computer over. Release the battery lock as shown. 2. Push the release latch, the battery pops up. 3. Remove the battery. Removing the Cover Securing Screws and Covers 1. Locate and loosen the seventeen (17) screws as shown. NOTE: It is not necessary to remove the screws from the cover.
2. Locate and remove the memory and HDD cover screws as shown. 3. Remove the memory cover as shown. 4. Remove the HDD cover as shown. Removing the HDD 1. 62 Locate the plastic tab on the HDD.
2. Place one hand on the computer for stability and grasp the HDD removal tag. 3. Pull away from the connector and upward as shown to remove the HDD from the chassis. Removing the Memory Module 1. Push the two release levers on the memory module outward as shown. NOTE: The memory module lifts upward during release. 2. Pull the memory module away from the socket.
Removing the Wireless Card NOTE: Fine tweezers are required for this procedure. 1. Locate the three antenna wires (white tape, red tape and no tape) on the left-hand side of the memory bay. 2. Using fine tweezers, grip the white taped wire and pull upward until it is released from the board. 3. Repeat for the red taped and no tape wires. 4. Remove cables to access Wireless Card. 5. Locate and remove the three screws as shown.
Removing the ODD 1. Push and hold the ODD latch as shown. 2. Remove ODD. Removing Dummy Trays 1. Locate Dummy Tray 1 and press the cover inwards as shown. 2.
3. Locate Dummy Tray 2 and press the release button as shown. 4. Remove Dummy Tray 2. Removing the Switch Cover CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 66 1. Turn the computer over. Locate and remove the two securing screws as shown. 2. Open the LCM module fully to expose the Switch Cover. 3. Grip the Switch Cover as shown and pull upward to remove.
4. Using two hands, remove the Switch Cover from the chassis. Removing the Keyboard 1. Locate and remove the two screws as shown. 2. Using both hands, lift the top edge of the keyboard as shown. 3. Turn the keyboard over, as shown, to expose the cables.
68 4. Using fine tweezers, release the first cable lock as shown and remove the cable from the socket. 5. Using fine tweezers, release the second cable lock as shown and remove the cable from the socket. 6. Remove keyboard from chassis.
Disconnecting the TouchPad 1. Disconnect the first cable by releasing the locking latch and removing the cable as shown. 2. Disconnect the second cable by releasing the locking latch and removing the cable as shown. NOTE: Move the cable away from the work area to allow access to the third cable. 3. Disconnect the third cable as shown.
Removing the Switch Board 1. Locate and remove the two screws as shown. 2. Remove the Switch Board from the chassis. Removing the Modem Module 1. 70 Disconnect the two cables from the Modem Module as shown.
2. Locate and remove the two securing screws as shown. 3. Lift the Modem Module clear of the chassis. Removing the Antenna Cables 1. Remove the Antenna Cables from the securing pins as shown. 2. Pull the three Antenna Cables from the underside of the computer through the mainboard as shown.
Removing the LCM Module CAUTION: Ensure all cables are removed from securing pins before proceeding to avoid damage. 1. Disconnect the LCM Module cable as shown. 2. Locate and remove the four screws as shown. 3. Lift the LCM Module upward to remove from the chassis. Removing the TouchPad 1. 72 Lift the rear edge of the TouchPad Module first, as shown, then pull the module away from the mounting to clear the ports at the front of the computer.
Removing the Mainboard 1. Locate the three connectors (yellow markers) as shown. 2. Disconnect the connectors using tweezers as shown. 3. Locate and remove the two screws as shown to release the Mainboard.
4. Grip the mainboard from the front and lift up. NOTE: If any resistance is met while removing the mainboard, ease the computer case outward to clear the obstruction. 5. Lift the mainboard clear of the chassis. Removing the I/O Board 74 1. Locate and remove the two screws as shown. 2. Lift the board toward the front of the computer to clear the port and remove from the chassis.
Removing the Heatsink and Fan Module 1. Turn the mainboard over. Locate and remove the five screws (red markers) and fan connector (yellow marker) from the mainboard. 2. Remove the Heatsink securing bracket as shown. 3. Remove the Heatsink as shown. 4. Steady the Mainboard with one hand and remove the Fan Module by lifting straight up.
Removing the CPU 76 1. Using a screw driver, unscrew the CPU counter clockwise. 2. Remove the CPU from the bracket as shown.
LCM Module Disassembly Procedure Removing the LCM Bezel CAUTION: When using tools, be careful not to scratch the computer casing. 1. Locate and remove the four mylar (small red markers) and two rubber (large red markers) screw covers as shown. NOTE: Do not discard the screw covers — they are reusable. 2. Remove the six bezel securing screws. 3. Loosen the bezel by lifting all the edges upward as shown. 4. Push in the cover locks to allow the bezel to pass freely over them.
5. Remove the bezel from the LCM Module. Removing the LCD Panel 78 1. Locate and remove the six screws as shown. 2. Locate the three panel connectors as shown. Disconnect the cables as shown.
3. Hold down the WebCam Module and remove the LCD panel by lifting the hinge as shown. 4. Locate and remove the Inverter Board screw as shown. 5. Grip the Inverter Board and lift upward to remove. 6. Grip the WebCam Module and lift upward to remove.
7. Turn the LCD panel over to expose the rear. Grip the LCM cable and lift upward to detach the adhesive pads. 8. Hold the printed circuit board with one hand and disconnect the cable by pulling away from the connector. 9. Locate and remove the four screws (two on each side) securing the LCD brackets to the LCD panel. 10. Remove the LCD brackets by pulling away from the LCD Panel as shown.
LCM Module Reassembly Procedure Replacing the LCD Panel 1. Align the LCD brackets the four screw holes (two on each side) on the LCD Panel as shown. 2. Secure the LCD brackets to the LCD panel. 3. Insert the cable into the cable connector on the LCD Panel as shown. 4. Align the LCD Panel cable as shown and press down to engage the adhesive pads.
82 5. Place the WebCam Module in the mounting as shown. 6. Place the Inverter Board in the mounting and secure with the screw provided. 7. Place the LCD Panel in the mounting and secure the three panel connectors as shown.
8. Secure the LCD Panel with the six screws provided. Replacing the LCM Bezel 1. Locate the bezel correctly and press down the edges until there are no gaps between the bezel and the LCM Module, 2. Secure the six screws provided and replace the mylar (small red markers) and rubber screw caps (large red markers).
Main Module Reassembly Procedure Replacing the CPU 1. Insert the CPU into the CPU bracket as shown. 2. Using a screw driver, tighten the screw clockwise as shown to secure the CPU in place. Replacing the Heatsink and Fan Module 84 1. Place the Fan Module in the mounting as shown. 2. Place the Heatsink as shown.
3. Align the Heatsink Securing Bracket as shown. 4. Secure the five screws and fan connector as shown. Replacing the I/O Board 1. Insert the board rear edge first as shown. 2. Replace the two screws as shown.
Replacing the Mainboard 1. Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the chassis, rear edge first, and press down to install. Replace the two securing screws as shown. NOTE: If any resistance is met while installing the mainboard, ease the computer case outward to clear the obstruction. 86 2. Replace the three connectors in the Mainboard sockets as shown. 3. Secure the Mainboard to the chassis using the two screws provided.
Replacing the TouchPad 1. Using both hands, replace the TouchPad, front edge first, as shown. NOTE: Ensure that the TouchPad cables are accessible once the TouchPad is in place and that all cables pass through the casing properly. Replacing the LCM Module 1. Align the four screw holes on the LCM Module hinges with the corresponding screw holes on the chassis. Lower the LCM Module into position as shown. Ensure that the LCM cables are inserted through the aperture before proceeding (yellow marker). 2.
Replacing the Antenna Cables 1. Ensure that the three LCM Module cable pass through the Mainboard and are accessible from the underside of the computer. Place the three cables in the wiring conduit and secure in place using the cable pins on the chassis. 2. Connect the LCM Module cable to the connector on the chassis as shown. Replacing the Modem 1. 88 Place the Modem in the mounting as shown. Insert the two screws provided to hold the Modem in place.
2. Reconnect the Modem cables as shown. Replacing the Switch Board 1. Place the Switch Board in the mounting as shown. 2. Secure the Switch Board in place using the screw provided. Reconnecting the TouchPad 1. Replace the connector as shown.
2. Insert the first cable as shown and lock the latch to secure the cable in place. 3. Insert the second cable as shown and lock the latch to secure the cable in place. Replacing the Keyboard 90 1. Using fine tweezers, insert the thicker cable into the socket and secure the locking latch as shown. 2. Using fine tweezers, insert the remaining cable into the socket and secure the locking latch as shown.
3. Turn the keyboard over and place the front edge first into the mounting. 4. Push the Keyboard into place toward the TouchPad and secure using the two screws provided. 5. Turn the Computer over and insert the screw as shown. Replacing the Switch Cover 1. Turn the computer over. Place the Switch Cover as shown and press down until no gaps are visible between the cover and the chassis.
2. Close the LCM Module. Locate and replace the two screws as shown. Replacing the Dummy Trays 1. Insert Dummy Tray 2 and push into the slot until flush with the chassis cover. 2. Insert Dummy Tray 1 and push into the slot until flush with the chassis cover. Replacing the ODD 1. 92 Insert the ODD and push into the slot until flush with the chassis cover.
Replacing the Wireless Card 1. Ensure the card is positioned label upwards as shown and push into the connector. NOTE: The card remains at an angle until the screws are inserted. 2. Secure the card in position using the two screws provided. 3. Reconnect the three Antenna Cables as shown, pushing down firmly to connect the cables.
Replacing the Memory Module 1. Push the memory module into the socket and press downward until it clicks into place. Replacing the HDD 1. Place the HDD in the mounting, rear edge first as shown. 2. Push firmly toward the connector to secure the HDD. Replacing the Covers 1. 94 Replace the HDD cover as shown.
2. Replace the two screws to secure the cover in place. 3. Replace the memory cover as shown. 4. Replace the two screws to secure the cover in place. 5. Replace the seventeen (17) screws to secure the cover in place.
Replacing the Battery Pack 96 1. Place the battery in the cradle rear edge first as shown. 2. Push the battery downward until it clicks in to place. 3. Engage the battery lock as shown.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: q Replace the System board. q If the problem is not corrected, see “Undetermined Problems” on page 114. If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes 006 Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages Real time clock error FRU/Action in Sequence RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility. RTC battery System board Memory size found by POST differed from CMOS Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages No beep, power-on indicator turns off and LCD is blank. FRU/Action in Sequence Power source (battery pack and power adapter). See “Power System Check” on page 99.. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 99..
Phoenix BIOS Beep Codes Code Beeps 02h Verify Real Mode 03h Disable Non-Maskable Interrupt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize chipset with initial POST values 09h Set IN POST flag 0Ah Initialize CPU registers 0Bh Enable CPU cache 0Ch Initialize caches to initial POST values 0Eh Initialize I/O component 0Fh Initialize the local bus IDE 10h Initialize Power Management 11h Load alternate registers with initial POST values 12h Restore CPU control wo
Code 46h Beeps 2-1-2-3 48h POST Routine Description Check ROM copyright notice Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h Initialize EISA board 52h Test keyboard 54h 58h Set key click if enabled 2-2-3-1 Test for unexpected interrupts 59h Initialize POST display service 5Ah Display pro
Code Beeps 8Ch Initialize floppy controller 8Fh Determine number of ATA drives (optional) 90h Initialize hard-disk controllers 91h Initialize local-bus hard-disk controllers 92h Jump to UserPatch2 93h Build MPTABLE for multi-processor boards 95h Install CD ROM for boot 96h Clear huge ES segment register 97h 98h Fixup Multi Processor table 1-2 Search for option ROMs. One long, two short beeps on checksum failure.
Code Beeps D2h POST Routine Description Unknown interrupt Code Beeps E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize the system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Initialize OEM special code EBh Initialize PIC and DMA ECh Initialize Memory type EDh Initialize Memory size EEh Shadow Boot Block EFh System memory
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error LCD backlight doesn't work Action in Sequence LCD is too dark Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. LCD brightness cannot be adjusted Reconnect the LCD connectors. LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Battery can’t be charged Action in Sequence See “Check the Battery Pack” on page 101. Battery pack System board PCMCIA-Related Symptoms Symptom / Error System cannot detect the PC Card (PCMCIA) Action in Sequence PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / Error Memory count (size) appears different from actual size.
Power Management-Related Symptoms Symptom / Error Battery fuel gauge in Windows doesn’t go higher than 90%. Action in Sequence Remove battery pack and let it cool for 2 hours. Refresh battery (continue use battery until power off, then charge battery). Battery pack System board System hangs intermittently. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / Error Action in Sequence System configuration does not match the installed devices.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 99.
Chapter 5 Jumper and Connector Locations Top View 1 CN2 LCM Cable CNTR 2 CN3 MDC CNTR 3 CN1 MDC Cable CNTR 4 CN5 Hot key board CNTR 5 CN4 Key board FFC CNTR 6 CN6 Fine track FFC CNTR 7 CN7 Smart card FFC CNTR 8 CN8 Touch pad FFC CNTR 9 CN9 MIC cable CNTR 10 CN12 3G card CNTR 11 CN14 Blue tooth cable CNTR 12 CN11 Speaker cable CNTR 13 CN13 Speaker cable CNTR 14 CN10 5in1 card reader CNTR Chapter 5 115
Bottom View 116 1 CN1004 MB & I/O board CNTR 15 Jack1003 Line-in jack 2 JACK1001 RJ-45 16 D1029 IR receiver 3 CN1001 Serial port 17 CN1016 PCI-E socket 4 CN1003 DVI port 18 CN6032 New card socket 5 CN1002 VGA port 19 CN1009 CPU socket 6 JACK1000 DC IN jack 20 CN1014 USB 7 CN1000 FAN cable CNTR 21 CN1010 USB 8 CN1005 Docking CNTR 22 CN1007 1394 9 CN1018 Second battery CNTR 23 U6002 North bridge 10 CN1008 ODD CNTR 24 U6004 South bridge 11 CN1015
Connector Descriptions CN1 RJ11 Connector (4-PIN) Signal name I/O PIN No. Signal name I/O 1 PIN No. MDMRNG_DOCK I/O 3 MDMRNG_DOCK I/O 2 MDMTIP_DOCK I/O 4 MDMTIP_DOCK I/O CN2 LCD I/F Connector (40-PIN) PIN No. I/O PIN No.
118 Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of the TravelMate 6592/6592G. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
TravelMate 6592/6592G Exploded Diagram 1 2 3 4 5 6 7 8 9 10 11 12 120 Chapter 6
13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 31 32 33 34 Category No. Part Name and Description Acer Part No. ADAPTER ADAPTER 135W 19V 3PIN W/LED DELTA ADP-135DB BBJF LF AP.13501.004 ADAPTER 135W 19V 3PIN LITE-ON PA-131-08 RI LF AP.13503.006 ADAPTER 135W 3PIN LSE SLS0317A19A52LF LF AP.13506.002 BATTERY PACK SANYO LI-ION 8 CELL2.4, 4800MAH BT.00803.019 BATTRY PACK SONY LI-ION 8CELL2.4, 4800MAH BT.00804.016 MODEM BOARD FOXCONN T60M845.02 54.AAMVN.001 WIRELESS LAN BOARD 802.
Category No. Part Name and Description Acer Part No. WIRELESS LAN BOARD 802.11BG PCI EXPRESS FOXCONN ABT_BRM4318BG 54.AAMVN.003 MINI WIRELESS BOARD 802.11 A/B/G MOW1 INTEL MM872612 KI.GLN01.001 MINI WIRELESS BOARD 802.11 A/B/G MOW2 INTEL MM872659 KI.GLN01.002 MINI WIRELESS BOARD 802.11 A/B/G ROW INTEL MM874511 KI.GLN01.003 MINI WIRELESS BOARD 802.11 A/B/G JP INTEL MM874740 KI.GLN01.004 MINI WIRELESS LAN BOARD 802.11BG INTEL WM3945AGBG KI.GLN01.005 BLUETOOTH BOARD FOXCONN T60H928.01 54.
Category No. Part Name and Description Acer Part No. AUDIO BOARD 55.AAMVN.004 TOUCHPAD BOTTON BOARD 55.AAMVN.005 TOUCHPAD SYNAPTICS TM61P-372 56.AAMVN.001 POWER CORD 3PIN USA 27.AAMVN.001 CABLE Chapter 6 POWER CORD 3PIN EUR 27.AAMVN.002 POWER CORD AUSTRALIA W/LABEL 27.AAMVN.003 POWER CORD 3PIN UK 27.AAMVN.004 POWER CORD 3PIN CHINA 27.AAMVN.005 POWER CORD 3PIN SWISS 27.AAMVN.006 POWER CORD SOUTH AFRICA (AIL) 27.AAMVN.007 POWER CORD 3PIN SOUTH AFRICA 27.AAMVN.
Category No. Part Name and Description Acer Part No. AUDIO BOARD CABLE 50.AAMVN.005 BUTTON BOARD CABLE 6 PINS 50.AAMVN.006 BUTTON BOARD CABLE 12 PINS 50.AAMVN.007 MODEM CABLE WITH RJ11 CONNECTOR 50.AAMVN.010 LOWER CASE 60.AAMVN.001 UPPER CASE 60.AAMVN.002 MIDDLE COVER 60.AAMVN.
Category Chapter 6 No. Part Name and Description Acer Part No. ASSY THERMAL COVER 60.AAMVN.004 SUPPORT COVER 60.AAMVN.005 HDD COVER 42.AAMVN,001 TOUCHPAD FRAME 42.AAMVN,002 MINI DUMMY CARD 42.AAMVN.003 PCMCIA DUMMY CARD 42.AAMVN.
Category No. Part Name and Description TOUCHPAD BRACKET Acer Part No. 33.AAMVN.001 (Note: The ACTUAL spare part: touchpad bracket does NOT contain touchpad bracket gesket. However the touchpad bracket image here has the touchpad bracket gesket. If you need to replace the touchpad bracket, please take off the gesket from old touchpad bracket and then stick them to new touchpad bracket.. CPU/PROCESSOR CPU INTEL YONAH CORE DUO FSB667 1.66G 2M SL8VR KC.23001.DTP CPU INTEL YONAH CORE DUO FSB667 1.
Category Chapter 6 No. Part Name and Description Acer Part No. DVD-RW MODULE 24X DUAL GBASE W/BEZEL 6M.AAMVN.002 OPTICAL BRACKET 33.AAMVN.002 DVD DUAL BEZEL G-BASE 42.AAMVN.012 DVD-RW DRIVE 8X DUAL PHILIPS SDVD841 W/O BEZEL KU.00809.004 DVD-RW DRIVE 8X DUAL TOSHIBA TS-L532U W/O BEZEL KU.00801.005 DVD-RW MODULE 24X SUPER MULTI GBASE W/BEZEL 6M.AAMVN.003 OPTICAL BRACKET 33.AAMVN.002 SUPER MULTI BEZEL GBASE 42.AAMVN.013 DVD-RW DRIVE 8X SUPER MULTI TOSHIBA TS-L632D W/O BEZEL KU.00801.
Category No. Part Name and Description Acer Part No. DVD-RW MODULE HD DVD ROM GBASE W/BEZEL 6M.AAMVN.006 OPTICAL BRACKET 33.AAMVN.002 HD DVD BEZEL 42.AAMVN.016 HD 1X DVD ROM TOSHIBA TS-L802A LF W/O BEZEL KV.01H01.001 FAN 23.AAMVN.003 HDD 100G 5400RPM SEAGATE ST9100824A KH.10001.007 HDD 100G 5400RPM TOSHIBA MK1032GAX KH.10004.002 HDD100G 5400RPM HGST MORAGA+ HTS541010G9AT00 ROHS F/W:A60A KH.10007.004 HDD 100G 5400RPM SAMSUNG HM100JC KH.1000B.
Category No. Part Name and Description Acer Part No. HDD 80G 5400RPM SATA TOSHIBA ARES-B_S MK8032GSX F/W AS111G KH.08004.005 HDD 80G SAMSUNG 5400RPM SATA HM080II M60S LF FW:YC200-08 KH.0800B.005 HDD 100G HGST SATA 1.5G NCQMORAGA+HTS541010G9SA00 FW:S60D KH.10007.005 HDD 100G SEAGATE 5.4K SATA KH.10001.008 ST9100824AS MERCURY 2 FW:3.06 LF HDD 100G TOSHIBA SATA 5.4K ARES- KH.10004.003 B_S MK1032GSX F/W AS021G HDD 100G 5400RPM SATA SAMSUNG HM100JI M60S LF FW:YH100-10 KH.1000B.003 HDD 120G SEAGATE 5.
Category No. Part Name and Description Acer Part No. AS9800 KEYBOARD DARFON KOREA KB.AAK07.006 AS9800 KEYBOARD DARFON UK KB.AAK07.007 AS9800 KEYBOARD DARFON GERMAN KB.AAK07.008 AS9800 KEYBOARD DARFON ITALIAN KB.AAK07.009 AS9800 KEYBOARD DARFON FRENCH KB.AAK07.010 AS9800 KEYBOARD DARFON SWISS/ G KB.AAK07.011 AS9800 KEYBOARD DARFON PORTUGUESE KB.AAK07.012 AS9800 KEYBOARD DARFON ARABIC KB.AAK07.013 AS9800 KEYBOARD DARFON BELGIUM KB.AAK07.014 AS9800 KEYBOARD DARFON SWEDEN KB.AAK07.
Category No. Part Name and Description Acer Part No. WIRELESS ANTENNA FOR 19.1IN. 25.AAMVN.001 CCD CAMERA 1.3M LOGITECH 56.AAMVN.002 LCD BEZEL 19" W/LOGO 60.AAMVN.006 LCD COVER W/LOGO 60.AAMVN.007 LCD BARCKET L W/HINGE 19.1IN. SAMSUNG 33.AAMVN.003 LCD BARCKET R W/HINGE 19.1IN. SAMSUNG 33.AAMVN.004 LCD 19IN. WXGA+ SAMSUNG LTN190- LK.19106.002 M2-000 8MS 300NITS NON-GLARE Chapter 6 LCD MODULE 19.1" WXGA+ CMO NON-GLARE 6M.AAMVN.012 INVERTER BOARD 19IN. TDK XAD369NR 4 LAMPS 19.AAMVN.
Category No. Part Name and Description Acer Part No. LCD CABLE 19.1IN. CMO W/CCD CABLE 50.AAMVN.012 WIRELESS ANTENNA FOR 19.1IN. 25.AAMVN.001 CCD CAMERA 1.3M LOGITECH 56.AAMVN.002 LCD BEZEL 19" W/LOGO 60.AAMVN.006 LCD COVER W/LOGO 60.AAMVN.007 LCD BARCKET L W/HINGE 19.1IN. CMO 33.AAMVN.005 LCD BARCKET R W/HINGE 19.1IN. CMO 33.AAMVN.006 LCD 19WXGA+ CMO M190A1-L01 8MS 300NITS NON-GLARE LK.1910D.003 LCD MODULE 19.1" WXGA+ SAMSUNG GLARE 6M.AAMVN.013 INVERTER BOARD 19IN.
Category Chapter 6 No. Part Name and Description Acer Part No. LCD CABLE 20.1IN. QDI W/CCD CABLE 50.AAMVN.021 WIRELESS ANTENNA FOR 20.1IN. 25.AAMVN.002 CCD CAMERA 1.3M LOGITECH 56.AAMVN.002 LCD BEZEL 20" W/LOGO 60.AAMVN.008 LCD COVER W/LOGO 60.AAMVN.007 LCD BARCKET L W/HINGE 20.1IN. 33.AAMVN.007 LCD BARCKET R W/HINGE 20.1IN. 33.AAMVN.008 LCD 20.1IN. WSXGA+ QDI QD20AL0101 8MS 300NITS NONGLARE LK.20109.001 LCD MODULE 20.1" WXGA+ AUO NON-GLARE 6M.AAMVN.022 INVERTER BOARD 20IN.
Category No. Part Name and Description LCD BEZEL 20" W/LOGO Acer Part No. 60.AAMVN.008 LCD COVER W/LOGO 60.AAMVN.007 LCD BARCKET L W/HINGE 20.1IN. 33.AAMVN.007 LCD BARCKET R W/HINGE 20.1IN. 33.AAMVN.008 LCD 20.1IN. WSXGA+ AUO M201EW01 V.2 8MS 300NITS GLARE LK.20105.003 MAINBOARD G72M/128MB SATA W/O CPU W/VGA HEATSINK & PCMCIA SLOT & RTC BATTERY MB.AAK0B.001 MAINBOARD G72M/128MB SATA W/O CPU W/VGA HEATSINK & PCMCIA SLOT & RTC BATTERY MB.AAK0B.
Category No. Part Name and Description Acer Part No. SO-DIMM DDRII533 256M HYNIX HYMP532S64BP6-C4 KN.2560G.012 SO-DIMM DDRII533 256MB NANYA NT256T64UH4A1FN-37B LF KN.25603.029 SO-DIMM DDRII533 512MB SAMSUNG M470T6554CZ3-CD500 LF KN.5120B.015 SO-DIMM DDRII533512M HYNIX HYMP564S64BP6-C4 KN.5120G.013 SO-DIMM DDRII533 512MB NANYA NT512T64UH8A1FN-37B LF KN.51203.023 SO-DIMM DDRII533 512M ELPIDA GU33512AGEPN612C KN.51209.005 SO-DIMM DDRII533 1GB MANYA NT1GT64UH8A0BN-37B LF KN.1GB03.
Category No. Part Name and Description Acer Part No. SPEAKER BUMPER 47.AAMVN.002 TOUCHPAD BRACKET GASKET 47.AAMVN.003 (Highlighted with red circles) EXTERNAL ANTENNA SET 25.AAMVN.004 ACER BLUETOOTH VOIP CARD PHONE KIT V2.2 W/CD & MANUAL LC.BTH01.008 REMOTE CONTROLLER RC-802 48KEY RT.8020A.001 ACCESSORY MCERC-200 REMOTE CONTROLLER LC.MCE05.001 MCEIR-210 RECEIVER LC.MCE05.002 MCEBS-220 IR BLASTER LC.MCE05.003 TV TUNER M103 S/W MPEG (HYBRID) 55.AAMVN.
Category Chapter 6 No. Part Name and Description Acer Part No. SCREW 86.AAMVN.003 SCREW 86.AAMVN.004 SCREW 86.AAMVN.005 SCREW 86.AAMVN.006 SCREW 86.AAMVN.007 SCREW 86.AAMVN.008 SCREW 86.AAMVN.009 SCREW 86.AAMVN.010 SCREW 86.AAMVN.011 SCREW 86.AAMVN.
138 Chapter 6
