Datasheet

Intel
®
Xeon
®
Processor 5500 Series Datasheet, Volume 1 141
Boxed Processor Specifications
Figure 8-5. Top Side Baseboard Keep-Out Zones
13
4
5678
B C D
A
123
4
5678
B C D
A
2200 MISSION COLLEGE BLVD. P.O. BOX 58119 SANTA CLARA, CA 95052-8119
R
49.90 [1.965]
SOCKET BODY OUTLINE,
FOR REFERENCE ONLY
44.70 [1.760]
CENTERLINE OF OUTER
SOCKET BALL ARRAY
47.50 [1.870]
SOCKET BODY OUTLINE,
FOR REFERENCE ONLY
41.66 [1.640]
CENTERLINE OF OUTER
SOCKET BALL ARRAY
36.00 [1.417]
SOCKET ILM
HOLE PATTERN
90.00 [3.543]
MAX THERMAL
RETENTION OUTLINE
90.00 [3.543]
MAX THERMAL
RETENTION OUTLINE
61.20 [2.409]
SOCKET ILM
HOLE PATTERN
80.00 [3.150]
THERMAL RETENTION
HOLE PATTERN
80.00 [3.150]
THERMAL RETENTION
HOLE PATTERN
D77712
102
DWG. NO SHT. REV
SHEET 1 OF 4DO NOT SCALE DRAWINGSCALE: 3.000
02
D77712
D
REV
DRAWING NUMBER
SIZE
THURLEY & GAINESTOWN
ENABLING KEEPIN / KEEPOUT
TITLE
EASD / PTMI
DEPARTMENT
FINISHMATERIAL DATEAPPROVED BY
-- 11/03/06J. WILLIAMS DATECHECKED BY 09/28/06N. ULEN DATEDRAWN BY 09/28/06N. ULEN DATEDESIGNED BY
UNLESS OTHERWISE SPECIFIED INTERPRET DIMENSIONS AND TOLERANCES IN ACCORDANCE WITH ASME Y14.5-1994 DIMENSIONS ARE IN MILLIMETERS TOLERANCES: .X # 0.0 Angles # 0.0 .XX # 0.00 .XXX # 0.000
THIRD ANGLE PROJECTION
THIS DRAWING CONTAINS INTEL CORPORAT ION CONFIDENTIAL INFORMATION. IT IS DISCLOSED IN CONFIDENCE AND ITS CONT ENTS MAY NOT BE DISCLOSED, REPRODUCED, DI SPLAYED OR MODIFIED, WITHOUT THE PRI OR WRITTEN CONSENT OF INTEL CORPORAT ION.
AS VIEWED FROM PRIMARY SIDE
OF THE MOTHERBOARD
NOTES: 1. THIS DRAWING TO BE USED IN CORELATION WITH SUPPLIED 3D DATA BASE FILE. ALL DIMENSIONS AND TOLERANCES ON THIS DRAWING TAKE PRECEDENCE OVER SUPPLIED FILE. 2. PRIMARY DIMENSIONS STATED IN MILLIMETERS. [BRACKATED] DIMENSIONS STATED IN INCHES 3. SOCKET KEEP OUT DIMENSIONS SHOWN FOR REFERNCE ONLY PLEASE REFER TO THE SOCKET B KEEPOUT / KEEPIN DRAWING FOR EXACT DIMENSIONS
4 BALL 1 LOCATION WITH RESPECT TO SOCKET BALL ARRAY IS
FORMED BY INTERSECTION OF ROW A & COLUMN 1. MAXIMUM OUTLINE OF SOCKET SOLDERBALL ARRAY MUST BE PLACED SYMMETRIC TO THE ILM HOLE PATTERN (INNER PATTERN) FOR PROPER ILM & SOCKET FUNCTION. 5. A HEIGHT RESTRICTION ZONE IS DEFINED AS ONE WHERE ALL COMPONENTS PLACED ON THE SURFACE OF THE MOTHERBOARD MUST HAVE A MAXIMUM HEIGHT NO GREATER THAN THE HEIGHT DEFINED BY THAT ZONE. ALL ZONES DEFINED WITHIN THE 90 X 90 MM OUTLINE REPRESENT SPACE THAT RESIDES BENEATH THE HEAT SINK FOOTPRINT. UNLESS OTHERWISE NOTED ALL VIEW DIMENSION ARE NOMINAL. ALL HEIGHT RESTRICTIONS ARE MAXIMUMS. NEITHER ARE DRIVEN BY IMPLIED TOLERANCES. A HEIGHT RESTRICTION OF 0.0 MM REPRESENTS THE TOP (OR BOTTOM) SURFACE OF THE MOTHERBOARD AS THE MAXIMUM HEIGHT. SEE NOTE 7 FOR ADDITIONAL DETAILS. 6. SEE SHEET 4 FOR REVISION HISTORY.
7 COMBINED COMPONENT AND SOLDER PASTE HEIGHT INCLUDING
TOLERANCES AFTER REFLOW.
BALL 1 POSITION 4
LINE REPRESENTS OF
OUTERMOST ROWS AND COLUMNS
OF SOCKET BALL ARRAY OUTLINE.
FOR REFERENCE ONLY
SOCKET BODY OUTLINE
FOR REFERENCE ONLY
LEGEND, THIS SHEET ONLY
ZONE 1: 0.0 MM MAX COMPONENT HEIGHT, NO COMPONENT PLACEMENT, SOCKET, ILM, AND FINGER ACCESS KEEPIN ZONE ZONE 2: 7.0 MM MAX COMPONENT HEIGHT 7 ZONE 3: 3.0 MM MAX COMPONENT HEIGHT 7 ZONE 4: 0.0 MM MAX COMPONENT HEIGHT, NO COMPONENT PLACEMENT RETENTION MODULE OR HEAT SINK TOUCH ZONE ZONE 5: 0.0 MM MAX COMPONENT HEIGHT, NO COMPONENT PLACEMENT, NO ROUTE ZONE ZONE 6: 1.97 MM MAX COMPONENT HEIGHT, SOCKET CAVITY 7