TravelMate 220/260 Service Guide Service guide files and updates are available on the CSD web; for more information, please refer to http://csd.acer.com.tw PART NO.: 49.49S01.021 PRINTED IN TAIWAN Download Free Service Manual at http://printer1.blogspot.
Revision History Please refer to the table below for the updates made on Travelmate 220/260 service guide. Date 01/03/2002 Chapter Chapter 1 Updates Revised CPU Type from Celeron 933 to celeron 1.06 GHz with 256KB cache Revised Super I/O Controller to Mitsubishi 38859F Revised CPU package to PIII 1 GHz uFCBGA2 and to Celeron 1.06 GHz UFPGA2 Revised BIOS version to AOEO Delete IBM(IC25N030ATD) Specifications for HDD Interface Changed TEAC to Mitsubishi and its specifications in CDROM interface.
Copyright Copyright © 2001 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV Screen messages Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI Download Free Service Manual at http://printer1.blogspot.
Table of Contents Chapter 1 System Introduction 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Removing the Video Capture Kit Covers . . . . . . . . . . . . . . . . . . . . . . . . . .59 Removing the 14.1” TFT LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Removing the 13.3” TFT LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Removing the Speakers (14.1” TFT LCD) . . . . . . . . . . . . . . . . . . . . . . . . .61 Removing the Speakers (13.3” TFT LCD) . . . . . . . . . . . . . . . . . . . . . . . . .61 Removing the Inverter Board . .
Table of Contents Appendix A Model Definition and Configuration 110 Appendix B Test Compatible Components 112 Microsoft Windows XP Home Edition Environment Test . . . . . . . . . . . . . . . . .113 Appendix C Index Online Support Information 114 116 Download Free Service Manual at http://printer1.blogspot.
Chapter 1 System Introduction Features This computer was designed with the user in mind. Here are just a few of its many features: Performance ! Intel® Mobile Pentium® III with 512KB cache or Celeron® CPU 1.
Human-centric Design and Ergonomics ! All-in-one design (CD-ROM, floppy disk drive, hard disk drive) ! Sleek, smooth and stylish design ! Full-sized keyboard ! Ergonomically centred touchpad pointing device Expansion ! One Type III or one Type II CardBus PC card (formerly PCMCIA) slot with ZV (zoomed video) support ! Upgrageable memory and hard disk ! 13.3” or 14.
System Block Diagram LCD Mobile Mobile CPU CPU CLK CLK GEN GEN Taulatin Taulatin 1G 1G Celeron Celeron 933, 933, 866 866 CRT CRT CONN CONN LVDZ VCH VCH HOST BUS 133MHz RGB MEMBUS 133MHz SO-DIMM*2 Almador Almador M M GMCH-MG GMCH-MG 830MG 830MG DVO BUS/66MHz INT. INT.
Board Layout Top View 4 2 5 67 8 9 10 11 12 13 3 1 14 15 16 22 17 18 21 1 CPU (on board) 12 PS/2 Port 2 Fan Connector 13 DC-in Port 3 Inverter connector 14 CD-ROM Connector 4 RJ45+RJ11 15 RTC battery connecto 5 External Display Port 16 Switch 6 USB Port 0 17 Internal Keyboard Cable Connector 7 USB Port 1 18 HDD Connector 8 LCD Connecto 19 Golden Finger 9 Hot Key Connector 20 TouchPad Cable Connector 10 Parallel Port 21 FDD Connector 11 Serial Port 22 Ca
Bottom View 1 2 3 9 8 4 7 6 5 1 Modem Connector 6 DIMM 1 Socket 2 North Bridge(82830MG) 7 Modem Card Cable Connector 3 Power Switch 8 Battery Connecto 4 Audio Board Connector 9 South Bridge (ICH3-M) 5 DIMM 2 Socket Download Free Service Manual at http://printer1.blogspot.
Panel Ports allow you to connect peripheral devices to your computer as you would with a desktop PC. Front Panel # Item Description 1 Display screen Also called LCD (Liquid Crystal Display), displays computer output. 2 Touchpad Touch-sensitive pointing device which functions like a computer mouse. 3 Floppy activity indicator LED (light-emitting diodes) that turn on and off when the floppy is active. 4 Floppy drive Internal diskette drive, accepts 3.
Left Panel # Icon Item/ Port Connects to... 1 Security keylock Kensington-compatible key-based computer security lock. 2 PCMCIA (PC card) Port Connects to one Type II or one Type III 16-bit PC card or 32-bit CardBus PC Card. 3 Eject button Eject PC cards from the card slots. 4 Power switch Turns on the computer power. 5 Speaker/ headphone-out jack Connects to audio line-out devices (e.g., speakers, headphones) 6 Line-in jack Accepts audio line-in devices (e.g.
Right Panel # Icon Item/ Port Connects to... 1 Video capture kit slot Accepts the video capture kit option on the right side of the computer. 2 Battery bay Houses the computer’s battery pack. 3 AcerMedia drive Houses removable media drive modules. 4 LED indicator Lights up when the AcerMedia drive is active. 5 Eject button Ejects the compact disc from the drive. 6 Emergency eject slot Ejects the compact discs when the computer is turned off.
# Icon Port Connects to... 5 External display port Connects to a display device (e.g., external monitor, LCD projector) and displays up to 64K colors at 1280x1024 resolution 6 Modem jack Connects to the phone line 7 Network jack Connects to an Ethernet 10/100-based network Bottom Panel # Item Description 1 Memory compartment Houses the computer’s main memory. 2 Hard disk anti-shock protection Protects your hard disk against shocks.
Indicators The computer has six easy-to-read status icons on the right of the display screen. . The Power and Standby status icons are visible even when you close the display cover so you can see the status of the computer while the cover is closed. # Icon Function Description 1 Power Lights when the computer is on. 2 Sleep Lights when the computer enters Standby mode and blinks when it enters into or resumes from hibernation mode.
Keyboard The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys. Special keys Lock keys The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock (Fn-F11) When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators ), -, *, and /).
Desired access Num lock on Num lock off Number keys on embedded keypad Type numbers in a normal manner. Cursor-control keys on embedded keypad Hold Shift while using cursor-control keys. Hold Fn while using cursor-control keys. Main keyboard keys Hold Fn while typing letters on embedded keypad. Type the letters in a normal manner.
Hot Keys The computer employs hot keys or key combinations to access most of the computer’s controls like screen contrast and brightness, volume output and the BIOS Utility. To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination. Hot Key Icon Function Description Fn-F1 Hotkey help Displays a list of the hotkeys and their functions. Fn-F2 Setup Accesses the notebook configuration utility.
Launch Keys Located at the top of the keyboard are four buttons. These buttons are called launch keys. They are designated as key 1, key 2, key 3 and key 4. By default, key 1 is used to launch the internet browser and key 2 is used to launch the e-mail application. Keys 3 and 4 starts the Launch Manager application. All four keys can be set by the user. To set the launch keys, run the Acer Launch Manager. Download Free Service Manual at http://printer1.blogspot.
Touchpad The built-in touchpad is a PS/2-compatible pointing device that senses movement on its surface. This means that the cursor responds as you move your finger on the surface of the touchpad. The central location on the palmrest provides optimum comfort and support. NOTE: When using an external USB or serial mouse, you can press Fn-F7 to disable the touchpad. If you are using an external PS/2 mouse, the touchpad is automatically disabled.
Function Execute Left Button Right Button Center Button Tap Click twice quickly Tap twice (at the same speed as doubleclicking a mouse button) Select Click once Tap once Drag Click and hold, then use finger to drag the cursor on the touchpad Tap twice (at the same speed as doubleclicking a mouse button) then hold finger to the touchpad on the second tap and drag the cursor Access context menu Scroll Click once Click and hold the up/ down buttons NOTE: Keep your fingers dry and clean when usin
Hardware Specifications and Configurations System Board Major Chips Item System core logic Controller Intel 830 MG with VGA integrated Intel ICH3-M with Audio integrated Super I/O controller SMCLPC4L47M227 Audio controller Intel ICH Video controller Intel 830MG Hard disk drive controller Embedded in Intel ICH3-M Keyboard controller Mitsubish 38859F RTC BQ3285LFHP Processor Item CPU type Specification Intel Mobile PIII with 512KB Cache Intel Celeron 1.
System Memory Item Specification Memory controller Intel 830MG Onboard memory size 0MB DIMM socket number 2 Sockets Supports memory size per socket 128/256/512 MB Supports maximum memory size 1024 MB (512MB x 2) Supports DIMM type SDRAM Supports DIMM Speed 133 MHz Supports DIMM voltage 3.3 V Supports DIMM package 144-pin so-DIM Memory module combinations You can install memory modules in any combinations as long as they match the above specifications .
Modem Interface Item Specification Chipset Ambit MDC module with Lucent modem controller Fax modem data baud rate (bps) 14.4K Data modem data baud rate (bps) 56K Supports modem protocol V.90MDC Modem connector type RJ11 Modem connector location Rear side Floppy Disk Drive Interface Item Specification Vendor & model name Mitsumi D353G W/I BEZ MCI JU-226A033 Floppy Disk Specifications Media recognition 2DD (720KB 2HD (1.2 MB, 3 mode) 2HD (1.
CD-ROM Interface Items Specification Vendor & Model Name MKE CR-177-B/D Mitsumi SR-243T CAV Mode: Read Sustained: Performance Specification Transfer rate 775~1800 blocks/sec Mode 1: 1545~3600 KB/sec Programmed I/O: 1550~3600 kBytes/sec Mode 2: 16.7 MB/sec Max. (Mode 0~4 Multi-word DMA: 1768~4106kBytes/sec 16.7 MB/sec Max. (Mode 0~2 Ultra DMA: 33.3MB/sec Max. Access time (typ.
DVD-ROM Interface Item Specification Data Buffer Capacity 512 kBytes Interface IDE Applicable disc format DVD: DVD-5, DVD-9, DVD-10, DVD-R (3.
Video Interface Item Specification Maximum resolution (LCD) 1024 x768 (32bit colors Maximum resolution (CRT 1024x768 (32 bit colors 1280x1024 (32 bit colors 1600x1200 (32 bit colors Video Memory Item Specification Fixed or upgradeable Fixed, share the system memory Video memory size 8MB Video Resolutions Mode Resolution Refresh Rate CRT Only LCD/CRT Simultaneous 640x480x256 90 60 640x480x64K 90 60 640x480x16M 90 60 800x600x256 90 60 800x600x64K 90 60 1024x768x256 90 60 Paral
Serial Port Item Specification Optional serial port IRQ (in BIOS Setup) IRQ4, IRQ3 USB Port Item Specification USB Compliancy Level 1.1 OHCI USB 1.
DC-DC/Charger Converter Item Output Rating Specification +5V 3.3V 12V 120mA Current (w/load, A 0~5A 0~4A Charger Output Li-ION Ni-MH Normal charge (charge while syste is not operative) 2.8A 2.25V Background charge (charge even system is still operative 0.8A Battery-low 2 level (V) 12.5V 8V Battery-low 3 level (V) 10V 7.
LCD Item Specification Supply voltage for LCD backlight (Vrms) 650 (typ.) 650 (typ.) AC Adapter Item Vendor & model name Specification Delta ADP-60DB Input Requirements Maximum input current (A, @90Vac, full load) 1.5 A @ 115Vac Nominal frequency (Hz 50-60 1.0 A @ 230Vac Frequency variation range (Hz) 47-63 Input voltage range (Vrms) 90-270 Inrush current The maximum inrush current will be less than 50A and 100A when the adapter is connected to 115Vac and 230Vac respectively.
Power Management Power Saving Mode Phenomenon Standby Mode Enter Standby Mode when ! ! The buzzer beeps The Sleep indicator lights u ! All power shuts off ! The display shuts off ! Hard disk drive is in standby mode. (spindle turned-off) 1.Standby/Hibernation hot-key is pressed and system is not ready to enter Hibernation mode. 2.System standby/ Hibernation timer expires and system is not ready to enter Hibernation mode. Hibernation Mode Enter Hibernation Mode (suspend to HDD) when 1.
Mechanical Specification Item Specification Drive Bays One Material Plastic Indicators Power-on, Standby, Battery Status, Media Access, CapsLock and NumLock Switch Power Memory Address Map Memory Address Size Function 00000000-0009FFFF 640 KB Base memory 80600000-80600FFF 4 KB Intel 82830MG 80620000-8063FFFF 128 KB 81000000-81FFFFF 000A0000-000CFFFF 3 MB 192 KB 08000000-08000FFF 4 KB 08001000-08001FFF 4 KB O2 Micro OZ6812 Cardbus Controller 82400000-82400FFF 4 KB USB 82200000-
IRQ Assignment Map Interrupt Channel Function NMI System errors IRQ0 System timer IRQ1 Keyboard IRQ2 Programmable interrupt controller IRQ3 Reserved IRQ4 COM1 IRQ5 Reserved IRQ6 Floppy IRQ7 LPT1 IRQ8 Real time clock IRQ9 SCI IRQ10 Audio/Mode IRQ11 USB/VGA/Cardbus IRQ12 PS2 pointing device IRQ13 Numeric data processor IRQ14 1st IDE device (hard disk) IRQ15 2nd EIDE device (CD-ROM drive) NOTE: IRQ settings may be changed by OS DMA Channel Assignment DMA Channel Function
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press m during POST (while the TravelMate logo is being displayed).
Multi-Boot Menu Users can press F12 during POST to enter the Multi Boot Selection Menu. In this menu users can change boot device without entering BIOS SETUP utility. Boot Menu Floppy Disk CD-ROM Hard Disk Realtek PXE2.0 Boot Agent #$ = Move highlight bar, Esc = Exit, F2 = Enter SETUP NOTE: If users disable the multi boot selection menu in BIOS SETUP utility, the message “ Press F12 to enter the multi boot selection menu” will not appear during POST.
System Information The System Information screen displays a summary of your computer hardware information. System Information CPU Type & Speed Floppy Disk Drive Hard Disk Drive HDD Serial Number System with System BIOS Version VGA BIOS Version Serial Number Asset Tag Number Product Name Manufacturer Name LAN Device UUID Page 1/1 Celeron 933 MHz 1.44 MB 3.5-inch XXXXX MB XXXXXXXXXXXXXXXXXXXX XXXROM Attached V3.
Basic System Settings The Basic System Settings screen allows you to set the system date and time. Basic System Setting Date Time page 1/1 [Mon Jan 1, 2001] [12:00] #$ = Move highlight bar, %& = Change setting, F1 = Help The following table describes the parameters in this screen. Parameter Description Format Date Sets the system date. DDD MMM DD, YYYY (day-of-the-week month day, year) Time Sets the system time.
The following table describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Boot Display Description Sets the display device during POST. Options Both or Auto When set to Auto, the computer automatically determines the display device. If an external display device (e.g., monitor) is connected, it becomes the boot display; otherwise, the computer’s display screen is the boot display.
Onboard Device Configuration The parameters in this screen are for advanced users only. You do not need to change the values in this screen because these values are already optimized. The Onboard Device Configuration screen assigns resources to basic computer communication hardware.
System Security The System Security screen contains parameters that help safeguard and protect your computer from unauthorized use. System Security Setup Password Power-on Password Hard Disk Password Processor Serial Number page 1/1 [None] / [Present] [None] / [Present] [None] / [Present] [None] / [Present] #$ = Move highlight bar, %& = Change setting, F1 = Help The following table describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
4. After setting the password, the computer automatically sets the chosen password parameter to Present. Three password types protect your computer from unauthorized access. Setting these passwords creates several different levels of protection for your computer and data: ! Setup Password prevents unauthorized entry to the BIOS Utility. Once set, you must key-in this password to gain access to the BIOS Utility. ! Power-On Password secures your computer against unauthorized use.
To change a password, follow the same steps used to set a password. To remove a password, follow the same steps used to set a password, except type nothing in the password boxes. Download Free Service Manual at http://printer1.blogspot.
Load Default Settings If you want to restore all parameter settings to their default values, select this menu item and press following dialog box displays. e. The If you would like to load factory- default settings for all parameters, use the cursor z / x keys to select Yes; then press e. Choose No if otherwise. Download Free Service Manual at http://printer1.blogspot.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: ! New versions of system programs ! New features or options Use the IFlash utility to update the system BIOS flash ROM. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use IFlash. NOTE: This program contains a readme.txt file. This readme.txt file will introduce on how to use IFlash utility. System Utility Diskette This utility diskette is for the TravelMate 220/260 series notebook machine.
Running PQA Diagnostics Program PQA Vx_x Result Diag SysInfo Press z / xto move around the main menu. Press are Diag, Result, SysInfo, Option and Exit. Option xx-xx-xx Exit e to enable the selected option. The main options The Diag option lets you select testing items and times. The following screen appears when you select Diag from the main menu.
The screen below appears if you select Multi Test. PQA PQA Diag Diag Vx_x Vx_x Result Result Diag Diag ONE One MULTI Multi FULL QUICK SysInfo SysInfo xx-xx-xx xx-xx-xx Option Option Exit Exit TEST TEST TEST TEST TEST TEST TEST COUNT VALUE (1...9999) 1 Specify the desired number of tests and press e. After you specify the number of tests to perform, the screen shows a list of test items (see below).
Download Free Service Manual at http://printer1.blogspot.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: ! Wrist grounding strap and conductive mat for preventing electrostatic discharge ! Flat-bladed screw driver ! Phillips screw driver ! Tweezers ! Flat-bladed screw driver or plastic stick NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. Download Free Service Manual at http://printer1.blogspot.
Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Main Unit Dx2 LCD Module CPU Heat Sink Plate Touch Pad Frame RTC Battery Touch Pad Frame W/ Touch Pad Button Touch Pad Board Touch Pad FPC Touch Pad Scroll Key Bx1 Ax8 Upper Case Kx4 CPU Heat Sink Hx1 Fx1 Charger Plate Audio Board Modem Board FDD Module Bx2 Hx2 Fx1 Gx1 CPU Fan Main Board FDD FDD Bracket FDD FPC FDD Bezel RTC Battery Holder Bx4 PCMCIA Plate PCMCIA Slot Ix6 I/O Port Bracket Modem Cable Download Free Service Manual at http://printer1.blogspot.
Screw List Item Description A M2.5*L6 (Black) B M2*L4 (Black) C M3*L4 (Silver) D M2*L10 (Black) E 2M*L3 (Silver) F M2.0*L4 (Black) G M2.5*L4 (Silver) H M2*L5 (Silver) I SCR. HEX NUT W / WASHER&NYLOK#4 (Silver) J CD-ROM SPECIAL SCREW (Silver) K CPU Heat Sink SPECIAL SCREW (Sky blue) Download Free Service Manual at http://printer1.blogspot.
Removing the Battery Pack 1. To remove the battery pack, push the battery release button inward then slide the battery pack out from the machine. Removing the Battery Cover 1. To remove the battery cover, press the cover side outward carefully then remove the cover. Download Free Service Manual at http://printer1.blogspot.
Removing the CD-ROM Drive Module 1. See “Removing the Battery Pack” on page 49 2. To remove the CD-ROM drive module, push the release button outward. 3. Slide it out from the machine. Disassembling the CD-ROM Drive Module 1. See “Removing the Battery Pack” on page 49 2. To disassemble the CD-ROM drive module, first remove four screws as shown. 3. Remove the CD-ROM drive module from the CD-ROM drive chassis. Download Free Service Manual at http://printer1.blogspot.
4. Remove the two screws from the CD-ROM board then remove the CDROM board from the drive. Download Free Service Manual at http://printer1.blogspot.
Removing the Hard Disk Drive Module 1. See “Removing the Battery Pack” on page 49 2. To remove the hard disk drive, first remove the hard disk drive cover screw, then remove the cover. 3. Remove the hard disk drive module out from the machine carefully. Disassembling the Hard Disk Drive Module 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hard Disk Drive Module” on page 52 3.
5. Bend both sides of the hard disk drive then remove the hard disk drive from the hard disk drive bracket. 6. Disconnect the hard disk drive connector from the hard disk drive. Download Free Service Manual at http://printer1.blogspot.
Removing the Extended Memory 1. See “Removing the Battery Pack” on page 49 2. To remove the Extended memory from the machine, first remove the screw from the memory cover. 3. Push the memory cover leftward to lift the cover off, then remove the memory cover. 4. Push out the latches on both sides of the socket and pull the memory module out from the socket. Download Free Service Manual at http://printer1.blogspot.
Removing the Modem Boar 1. See “Removing the Battery Pack” on page 49 2. To remove the modem board, first remove the screw from the modem cover. 3. Remove the modem cover from the machine. 4. Remove two screws from the modem board as shown, then remove the modem board from the main unit carefully by using a plastic bladed screw driver. 5. Disconnect the modem cable from the modem board, then remove the modem board. Download Free Service Manual at http://printer1.blogspot.
Disassembling the LCD Removing the Hinge Caps 1. See “Removing the Battery Pack” on page 49 2. To remove the hinge caps, push the hinge caps outward then slide the hinge caps out from the main unit. Removing the Middle Cover 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. To remove the middle cover, push the middle cover rightward and lift the middle cover away. . Removing the Launch Board 1. See “Removing the Battery Pack” on page 49 2.
5. Remove the two screws from the launch board then remove the launch board from the middle cover. Removing the Cable Cover 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. To remove the cable cover, push the cable cover backward then pull the cover off gently. Removing the Keyboard 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3.
5. Disconnect the keyboard cable from the main board carefully, then remove the keyboard from the main board. Removing the LCD Module 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. Remove the two screws from the rear of the unit and the two from the base of the unit 7.
8. Disconnect the inverter cable from the main board and then remove the LCD module from the main unit. 9. Disconnect the launch board cable from the main board and remove it. Removing the Video Capture Kit Covers 1. See “Removing the Battery Pack” on page 49 2. Remove the video capture kit cover from the LCD module on each side in the way as shown here. . Removing the 14.1” TFT LCD Bezel 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3.
7. Use tweezers to remove the five LCD cushions on the LCD bezel, and then remove the three screws below from the LCD bezel. 8. Snap off the bezel carefully, and then remove the LCD bezel from the LCD module. Removing the 13.3” TFT LCD Bezel 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6.
8. Snap off the bezel carefully, and then remove the LCD bezel from the LCD module. Removing the Speakers (14.1” TFT LCD) 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56r 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the 14.1” TFT LCD Bezel” on page 59 8.
6. See “Removing the LCD Module” on page 58 7. See “Removing the 13.3” TFT LCD Bezel” on page 60 8. To remove the speakers, first remove the two screws from the speakers. 9. Detach the speakers from the LCD panel, disconnect the speaker cable from the speakers and then remove the speakers from the LCD module. Removing the Inverter Board 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4.
9. Disconnect the microphone cable and then remove the inverter board from the LCD panel. 10. Disconnect the LCD power cable and the inverter cable from the inverter board. Removing the 14.1” TFT LCD 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the 14.
Removing the 13.3” TFT LCD 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the 13.3” TFT LCD Bezel” on page 60 8. To remove the LCD, first remove the two screws from the LCD, then remove the LCD from the LCD panel. Removing the 13.3” TFT LCD Brackets 1.
8. Remove two screws on each side to remove the LCD brackets. Removing the LCD Coaxial Cable 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the 14.1” TFT LCD Bezel” on page 59 8. See “Removing the 13.3” TFT LCD Bezel” on page 60 9. See “Removing the 14.
Removing the Microphone Cable 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the 14.1” TFT LCD Bezel” on page 59 8. See “Removing the 13.3” TFT LCD Bezel” on page 60 9. See “Removing the 14.1” TFT LCD” on page 63 10. See “Removing the 13.
Disassembling the Main Unit Removing the CPU Heat Sink Plate 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. Remove two screws from the CPU heat sink plate. 6. Lift the CPU heatsink plate from the main unit. Removing the RTC Battery 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3.
6. Detach the touch pad frame together with the touch pad button from the upper case carefully. 7. Remove the touch pad scroll key from the upper case. 8. To detach the touch pad board, first disconnect the touch pad cable from the touch pad board and then remove the touch pad board from the upper case. Removing the Touch Pad Cable 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4.
Removing the Upper Case 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. Remove the screw as shown here and disconnect the FDD cable from the main unit. 10.
11. Pull the upper case from the unit gently. Removing the RTC Battery Holder 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10.
10. Pull the floppy disk drive module out from the upper case carefully. Disassembling the Floppy Disk Drive Module 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the Upper Case” on page 69 9.
Removing the Charger Plate 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10.
Removing the CPU Fan 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10. See “Removing the CPU Heat Sink” on page 72 11.
4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10. Remove the screw from the audio board and then detach the audio board. Removing the Main Board 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3.
15. Detach the main board from the lower case carefully in the way as shown here. Removing the PCMCIA Slot 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9.
16. Detach the PCMCIA slot from the main board. Removing the I/O Port Bracket 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10.
Removing the Modem Cable 1. See “Removing the Battery Pack” on page 49 2. See “Removing the Hinge Caps” on page 56 3. See “Removing the Middle Cover” on page 56 4. See “Removing the Keyboard” on page 57 5. See “Removing the Cable Cover” on page 57 6. See “Removing the LCD Module” on page 58 7. See “Removing the CPU Heat Sink Plate” on page 67 8. See “Removing the RTC Battery” on page 67 9. See “Removing the Upper Case” on page 69 10. See “Removing the Charger Plate” on page 72 11.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. See “System Diagnostic Diskette” on page 39 for details. 1.
Keyboard or Auxiliary Input Device Check Remove the external keyboard if the internal keyboard is to be tested. If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board. If the keyboard cable connection is correct, run the Keyboard Test. See “System Diagnostic Diskette” on page 39 for details.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: ! Replace the System board. ! If the problem is not corrected, see “Undetermined Problems” on page 91. If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes 006 Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error 3. IDE Secondary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Erro 071 CMOS Battery Bad 072 CMOS Checksum Erro 110 Incorrect password specified, system disabled.
Error Message List Error Messages Real time clock error FRU/Action in Sequence RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility. RTC battery System board Memory size found by POST differed from CMOS Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages FRU/Action in Sequence No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 80. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 80.
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error LCD backlight doesn't work Action in Sequenc LCD is too dark Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. LCD brightness cannot be adjusted Reconnect the LCD connectors. LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't work).
PCMCIA-Related Symptoms Symptom / Error System cannot detect the PC Card (PCMCIA) Action in Sequenc PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / Error Memory count (size) appears different from actual size. Action in Sequenc Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system. DIMM System board Speaker-Related Symptoms Symptom / Error In Windows, multimedia programs, no sound comes from the computer.
Power Management-Related Symptoms Symptom / Error System hangs intermittently. Action in Sequenc See “Thermal & Fan Utility” on page 39. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / Error System configuration does not match the installed devices. Action in Sequenc Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system. Reconnect hard disk/CD-ROM/diskette drives. External display does not work correctly.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 80): 1.
Index of AFlash BIOS Error Message Error Message Hardware Error Action in Sequence See “System Diagnostic Diskette” on page 39 VPD Checksum Error Reboot the system and then retest with this diskette. BIOS Update Program Erro Turn off the power and restart the system. System Error Make sure this AFlash BIOS diskette for this model. Without AC adapter make sure to connect AC adapter Battery Low make sure to install a highly charged battery, and reboot system.
Index of PQA Diagnostic Error Code, Message Error Code Message 16XXX Backup battery error 01XXX CPU or main board error Action in Sequence Backup battery Reload BIOS default setting.
Chapter 5 Jumper and Connector Locations Top View 4 5 67 8 9 10 11 12 13 3 2 1 14 15 16 22 17 18 21 20 19 PCB No.
Keyboard Switch Settings SW1-1 SW1-2 English OFF OFF Japanese ON OFF Europe OFF ON SW-4/5 SW1-4 SW1-5 Acer OFF OFF OEM1 ON OFF OEM2 OFF ON OEM3 ON ON SW1-6: Check Password SW1-6 = ON, Disable SW1-6 = OFF, Enable SW1-7: Boot Block Boot SW1-7 = OFF, Enable SW1-7 = On, Disable Download Free Service Manual at http://printer1.blogspot.
Bottom View 1 2 3 9 8 4 7 6 5 1 Modem Connector 6 DIMM 1 Socket 2 North Bridge (82830MG) 7 Modem Card Cable Connector 3 Power Switch 8 Battery Connector 4 Audio Board Connector 9 South Bridge (ICH3-M) 5 DIMM 2 Socket Download Free Service Manual at http://printer1.blogspot.
Download Free Service Manual at http://printer1.blogspot.
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 220/260. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Exploded Diagram Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description Memory NS MEMORY SDIMM 256 SODIMM 256M HYS64V32220GDL7.5 05 LCD 14.1" XGA LCD 14.1" XGA AU/B141XN04/3 NS CABLE ASSY MODEM FALCON2 CABLE ASSY MODEM FALCON NS C.A. LAUNCH FALCON2 C.A. LAUNCH FALCON2 NS CABLE ASSY MICRO (13.3” &12.1”) FL CABLE ASSY MICRO (13.3” &12.1”) FL NS CABLE ASSY LED & INV (14.1”) FL2 CABLE ASSY LED & INV (14.1”) FL2 LCD Cable Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description NS CORD 125V UL 3P K01081183WP CORD 125V UL 3P K01081183WP NS CABLE ASSY FDD FPC FALCON2 CABLE ASSY FDD FPC FALCON2 NS ASSEMBLY LOWER CASE FALCON3M ASSEMBLY LOWER CASE FALCON3M 10 ASSY LCD PANEL 14.1” PNL ASSY LCD PANEL 14.1” ADT 08 ASSY LCD BEZEL 14.1’ BZL ASSY LCD BEZEL 14.
Picture No. Partname Description 09 ASSEMBLY HDD DOOR ASSEMBLY HDD COVER F3M 15 ASSEMBLY MODEM COVER F3M ASSEMBLY MODEM COVER F3M 14 ASSEMBLY DIMM COVER F3M ASSEMBLY DIMM COVER F3M NS ASSEMBLY CHARGER PLATE F3M ASSEMBLY CHARGER PLATE F3M 03 BRACKET FDD REAR F3M BRACKET FDD REAR F3M 17 ASSY FDD BEZEL BZL ASSY FDD BEZEL PANASONIC F3M Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description NS ASSEMBLY CD/DVD CHASSIS F3M ASSEMBLY CD/DVD CHASSIS F3 NS HDD ASSY(9.5MM) BRACKET FALCON2 HDD ASSY(9.5MM) BRACKET FALCON2 07 CAP HINGE L HIGH F3 CAP HINGE L HIGH F3 06 CAP HINGE R HIGH F3 CAP HINGE R HIGH F3M NS COVER CABLE F3M COVER CABLE F3M 04 BATTERY COVER F3 DOOR BATTERY F3M Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description NS RTC BATTERY HOLDER F3M HOLDER RTC BATTERY F3M NS INVERTER Ambit T62.172.00 V.60 FAL INVERTER T62I172.00 REV.60 FAL NS MODEM BOARD AMBIT/ T60M283..00 MODEM MDC AMBIT/T60M283..00 3A NS LAUNCH BOARD FALCON2 LAUNCH BOARD NS TM210 AUDIO BOARD F2 TM210 AUDIO BOARD F2 NS FALCON 3M CD-ROM BD FALCON 3M CD-ROM BD NS RTC BTY LI 3V BTY LI 3V CR2032T6 210MAH 50MM Board Battery Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description NS BTY PACK LI+/PANASONIC BTY PACK LI+ 2AH 8CELL PANA NS ADT 60W ADP-60DHBN 3P ADT 60W ADP-60DHBN 3P NS KEYBOARD KB US NSK-84X21 NS KEYBOARD KB US/INTERNATIONAL NSK-84X22 NS KEYBOARD KEYBOARD CHINESE NSK-84X2C 09 SPEAKER-R (14.1”) FL2.5 SPEAKER-R (14.1”) FL2.5 09 SPEAKER-L (14.1”) FL2.5 SPEAKER-L (14.1”) FL2.5 02 HEATSINK CPU F3M HEATSINK CPU F3M Adapter Keyboard Speaker Heatsink Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description FDD/Floppy Disk Drive 29 ASSY FDD MODULE 1.44 PANASONIC F3 ASSY FDD MODULE PANASONI F3M NS FDD 1.44M FDD 1.44M MCI/JU226A253F NS HDD MODULE IBM 20G F3 ASSY HDD MODULE IBM 20G F3M NS HDD 20G IB HDD 20G IBM/IC25N920ATDA04 NS ASSY DVD-ROM MODULE TM220 ASSY DVDROM MODULE PIONEER F3M NS DVD-ROM 8X MATSUSHITA DVD-ROM 8X MKE/SR-8176BAA2 ME34 HDD/Hard Disk Drive DVD-ROM DRIVE Download Free Service Manual at http://printer1.blogspot.
Picture No. Partname Description Mainboard NS MAINBOARD W/CPU CEL-933 TM220 FALCON 3M MB W/CPU CEL-933 NS PCMCIA SLOT/PC CARD SLOT CONN CARDPUSH 1 CA91501-TC-F2 NS CONNECTOR 22PIN CONN CTR ML 22P HH98227 A2(HDD) NS PLATE CPU HEATSINK F3M PLATE CPU HEATSINK F3M NS PLATE PCMCIA F3M PLATE PCMCIA F3M NS LBL NAME PLATE 99.8*8.3 TM220 LBL NAME PLATE 99.8*8.
Picture No. Partname Description Screws NS M/B, CASE, POWER SUPPLY SCREW SCR. HEX NUT W/WASHER&NYLOK #4 NS SCREW SCREW CPU FALCON 2.5 NS SCREW BINDING BL-ZN M2*.4P SCREW BINDING BL-ZN M2*.4P NS SCREW BINDING BL-ZN M2*4L SCREW BINDING BL-ZN M2*4L NS SCREW M2L5 BH MSN+N SCREW M2L5 BH MSN+ NS LCD SCREW SCREW M2.5X6 Download Free Service Manual at http://printer1.blogspot.
Download Free Service Manual at http://printer1.blogspot.
Appendix A Model Definition and Configuration Model Number Definitions Model Number LCD CPU Memory HD CD/DV Battery 261X 14.1” TFT Pentium III 1G 256MB 20GB CD-RO Li-ion 260XC 14.1” TFT Pentium III 1G 256MB 20GB Combo or DVD-ROM Li-ion 260XV 14.1” TFT Pentium III 1G 256MB 10GB DVD-ROM Li-ion Download Free Service Manual at http://printer1.blogspot.
Download Free Service Manual at http://printer1.blogspot.
Appendix B Test Compatible Component This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows XP Home Edition. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the TravelMate 220/260 series notebook Compatibility Test Report released by the Acer Mobile System Testing Department.
Microsoft Windows XP Home Edition Environment Test Item Processor Specifications Pentium III 1G above, 256k (TravelMate 260) Celeron 1.06G, 256k (TravelMate 220) Memory Infineon 128MB Infineon 256MB LCD 13.3” XGA TFT (AU) 14.1” XGA TFT (AU) Floppy Disk Drive Hard Disk Drive MCI IBM 10GB 9.5mm IBM 20GB 9.
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Download Free Service Manual at http://printer1.blogspot.
Index A CD-ROM Interface AFLASH Utility Audio Chipsets 25 AC Adapter 20 17 computer 40 10 on indicator 17, 21 contrast B 13 Controllers 17 Core logic 17 hotkeys Battery 23 battery pack charging indicator BIOS CPU 10 17 17 package 17 type 17 core voltage 17 I/O voltage 17 17 ROM type 17 vendor 17 Version 17 package ROM size BIOS Setup Utility D DC-AC LCD Inverter 30 BIOS Supports protocol 2 DIMM 18 Design 30–?? BIOS Utility 33 Load Default Settings 39 Navigating 31 Basic Sys
F 10 on indicator Features Memory 1 Flash Utility Address Map 40 Memory Address Map Floppy Disk Drive Interface 19 FRU (Field Replaceable Unit) List Memory Check 98 Modem Hard Disk Drive Module 19 hotkey 26 13 num lock Hardware Specifications and Configurations 15 17, 19 Hibernation Mode O 26 Online Support Information 13 Hot Keys 13 hotkey 114 P Panel I 5 Bottom Rear 27 10 90 IRQ Assignment Map 28 Parallel Port Intermittent Problems 9 8 8 right Indicators 10 on ind
R T Removing the Battery Pack 49 Temperature 98 RTC 17 RMA 26 Test Compatible Components Touchpad 112 15 touchpad S hotkey Second Level Cache Serial Port 17 hotkey U 13 Standby Mode Super I/O 82 Troubleshooting 78 Touchpad Check 22 speakers 13 26 Undetermined Problems 17 USB System 91 23 utility Block Diagram Layout 3 4 79 System Diagnostic Diskette 40 System Memory 18 System Utilities 30 System Utility Diskette 40 System Check Procedures BIOS 30–?? V Video 21, 22 22 Vid
Download Free Service Manual at http://printer1.blogspot.
