TravelMate 230/ 280 Service Guide PART NO.: 49.46W01.
Revision History Please refer to the table below for the updates made on HP Lapin service guide. Date 01/20/2003 Chapter Cover page Updates Correct typo on page II Dual high quality stereo speakers on page 2 Modify item 3 media activity on page 12 Supports memory size per socket: 512MB on page 19 USB Compliancy Level: USB 2.
Copyright Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV Screen messages Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Table of Contents Chapter 1 System Introduction 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Appendix C Index VIII Online Support Information 151 153
Chapter 1 System Introduction Features This computer was designed with the user in mind. Here are just a few of its many features: Performance T T Intel® Mobile Celeron Pentium® 4 series processors from 1.6G up tp 2.0G with 512KB cache (TravelMate 230) Intel® Mobile Northwood Pentium® 4 series processors from 1.6G up tp 2.
Expansion K K One CardBus PC Card (formerly PCMCIA) Type III slot. Upgrageable memory and hard disk I/O Ports K K K K K K K K K K K One VGA port, I2 C compatible (Optional) One DC-in port (AC adapter) Dual high quality stereo speakers One line-in One line-out One CardBus type III slot (3.3V, 5V, 12V support) Four USB ports (2 ports optional) Two IEEE 1394 ports (optional) One ECP parallel port One RJ-11 port One RJ-45 jack Display K K K K 14.
Opening and closing the display To open the display, slide the display cover latch to the right and lift up the cover. Then tilt it to a comfortable viewing position. The computer employs a microswitch that turns off the display (and enters standby mode) to conserve power when you close the display cover, and turns it back on when you open the display cover. NOTE: If an external monitor is connected, the computer turns off the display (but does not enter standby mode) when you close the display cover.
System Block Diagram EXTERNAL SPEED STEP CIRCUIT Mobile CPU CLK GEN ICS 94239 P4-M Northwood P4-M Celeron G768D HOST BUS 100MHz MCH Brookdale-GL DDR*2 266MHz RGB CRT CONN DVO Chrontel LVDS 7019 INT. MIC HUB I/F LCD Dual Channel 66MHz PCI BUS CARDBUS OZ 6912 MIC IN AC ‘97 AC-Link CODEC Line In CARDBUS ONE SLOT PWR SW OZ2211S MINI PCI 802.
Board Layout Top View PCB No.
Bottom View 1 Modem Cable Connector 7 Modem Connector 2 North Bridge (845-GL) 8 Battery Connector 3 DIMM Socket 1 9 CardBus Controller (OZ6912T) 4 Audio Board Connector 10 LAN Controller (RTL8100BL) 5 DIMM Socket 2 11 LVDS 6 South Bridge (ICH4) Chapter 1 6
Panel Ports allow you to connect peripheral devices to your computer as you would with a desktop PC. Front Panel # 7 Item Description 1 Display screen Also called LCD (Liquid Crystal Display), displays computer output. 2 Status indicators LEDs (Light Emitting Diodes) that turn on and off to show the status of the computer and its functions and components. 3 Touchpad Touch-sensitive pointing device which functions like a computer mouse.
Left Panel # Icon Item/ Port Description 1 PCMCIA (PC card) Port Connects to one Type III 16-bit PC card or 32-bit CardBus PC Card. 2 Eject button Eject PC cards from the card slots. 3 Floppy activity indicator LED (light-emitting diodes) that turn on and off when the floppy is active. 4 Speaker/ headphone-out jack Connects to audio line-out devices (e.g., speakers, headphones) 5 Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).
Right Panel # 9 Icon Item/ Port Description 1 Battery bay Houses the computer’s battery pack. 2 Optical drive Houses removable optical drive modules. 3 LED indicator Lights up when the optical drive is active. 4 Eject button Ejects the compact disc from the drive. 5 Emergency eject slot Ejects the compact discs when the computer is turned off. 6 Security keylock Kensington-compatible key-based computer security lock.
Rear Panel # Icon Port Description 1 Power Jack Connects to an AC adapter 2 Parallel port Connects to a parallel device (e.g., parallel printer) 3 USB port (two) Connects to any Universal Serial Bus devices(e.g., USB mouse, USB camera). 4 Modem jack Connects to the phone line 5 Network jack Connects to an Ethernet 10/100-based network 6 External display port Connects to a display device (e.g.
Bottom Panel # 1 11 Item Battery bay Description Houses the computer’s battery pack. 2 Battery release latch Unlatches the battery to remove the battery pack. 3 Hard disk bay Houses the computer’s hard disk (secured by a screw). 4 Memory compartment Houses the computer’s main memory.
Indicators The computer has six easy-to-read status icons on the right of the display screen. The Power and Standby status icons are visible even when you close the display cover so you can see the status of the computer while the cover is closed. # Icon Function Description 1 Power Lights when the computer is on. 2 Sleep Lights when the computer enters Standby mode and blinks when it enters into or resumes from hibernation mode.
Keyboard The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys. Special keys Lock keys The keyboard has three lock keys which you can toggle on and off. @ ] [ Lock key @ ] [ Description Caps Lock When Num Lock (Fn-F11) When is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode when you need to do a lot of numeric data entry.
Desired access Num lock on Num lock off Number keys on embedded keypad Type numbers in a normal manner. Cursor-control keys on embedded keypad Hold Shift while using cursor-control keys. Hold Fn while using cursor-control keys. Main keyboard keys Hold Fn while typing letters on embedded keypad. Type the letters in a normal manner.
Hot Keys The computer employs hot keys or key combinations to access most of the computer’s controls like screen contrast and brightness, volume output and the BIOS Utility. To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination. Hot Key Fn- l Fn- Function Description Hotkey help Displays a list of the hotkeys and their functions. m Setup Accesses the notebook configuration utility.
z { } a Hot Key Icon Function Description Brightness down Decreases the screen brightness. Fn- Home Functions as the Fn- End Functions as the Euro Types the Euro symbol. Fn-¨ Gr-Euro g d key. key. The Euro symbol If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a European layout, you can type the Euro symbol on your keyboard. NOTE: for US keyboard users: The keyboard layout is set when you first set up Windows.
Launch Keys Located at the top of the keyboard are five buttons. These buttons are called launch keys. They are designated as wireless LAN/Bluetooth , Web Browser button, mail button, P1 andP2. By default, P1 and P2 are users programmable. The Web Browser button, by default, is used to launch the internet browser The mail button is used to launch the e-mail application. The LED of the mail button will flash when the user has received an incoming email.
Hardware Specifications and Configurations System Board Major Chips Item Controller System core logic Intel ICH4 Super I/O controller Mitsubish 38857 Audio controller Cirrus CS4299XQ Video controller Intel 845GL Hard disk drive controller Embedded in Intel ICH4 Keyboard controller Mitsubish 38857 CardBus Controller OZ 6912T-U RTC Intel ICH4 Processor (for TravelMate 230) Item Specification CPU type Intel Celeron Pentium 4 CPU package To 2.0GHz uFCBGA CPU core voltage 1.
Second Level Cache Item Specification 2nd level cache control Always Enabled Cache scheme control Fixed-in write back System Memory Item Specification Memory controller Intel 845GL Onboard memory size 0MB DIMM socket number 2 Sockets Supports memory size per socket 512MB Supports maximum memory size 1024MB Supports DIMM type DDR-DRAM SODIMM Supports DIMM Speed 266 MHz Supports DIMM voltage 3.
Modem Interface Item Specification Chipset Ambit MDC module with Lucent modem controller Fax modem data baud rate (bps) 14.4K Data modem data baud rate (bps) 56K Supports modem protocol V.90/V.92MDC Modem connector type RJ11 Modem connector location Rear side Floppy Disk Drive Interface Item Specification Vendor & model name Mitsumi D353G W/I BEZ MCI JU-226A293 Floppy Disk Specifications Media recognition 2DD (720KB) 2HD (1.2 MB, 3 mode) 2HD (1.
CD-ROM Interface Items Specification Vendor & Model Name Mitsumi SR-244W1 Performance Specification Transfer rate Read Sustained: 1545~3600 KB/sec Programmed I/O: 16.7 MB/sec Max. (Mode 0~4) Multi-word DMA: 16.7 MB/sec Max. (Mode 0~2) Ultra DMA: 33.3MB/sec Max. Access time (typ.
DVD-ROM Interface Item Average Full Access time (typ.) Specification Random (*1) DVD-5: CAV mode 110 msec typical 150 msec average max Random (*4) 120 msec typical 160 msec average max Full Stroke (*2) CAV mode 200 msec typical 260 msec average max Full Stroke (*5) 270 msec typical 350 msec average max DVD-9: Random (*7) 150 msec typical 200 msec average max Full Stroke (*8) 340 msec typical 450 msec average max DVD-RAM (2.
(*9) Disk: ODSC-PARA Combo Drive Interface Item Vendor & model name Specification KME UJDA740 Performance Specification Transfer rate (KB/sec) Read Sustained: DVD-ROM MAX 8X CAV (MAX 10800 KB/sec) CD-ROM MAX 24X CAV (MAX 3600 KB/sec) CD-R 4X, 8X (CLV), Max 16X, MAX 24X (ZCLV) Write: CD-RW 4X (CLV) HS-RW 4X,8X, 10X (CLV) ATAPI Interface: PIO mode 16.6 MB/sec :PIO Mode 4 DMA mode 16.6 MB/sec:Multi word mode 2 Ultra DMA mode 33.
Audio Interface Item Specification Supports PnP DMA channel DMA channel 0 Supports PnP IRQ IRQ10, IRQ11 DMA channel 1 Video Interface Item Specification Vendor & Model Name Intel 845GL Chip voltage Core / 2.5V, 1.5V, 1.
USB Port Item Specification USB Compliancy Level 2.0 OHCI USB 2.
DC-DC/Charger Converter Item Specification Normal charge (charge while system is not operative) 2.8A 2.25V Background charge (charge even system is still operative) 0.8A Battery-low 2 level (V) 12.5V 8V Battery-low 3 level (V) 10V 7.
AC Adapter Item Vendor & model name Specification Delta ADP-65DB Input Requirements Maximum input current (A, @90Vac, full load) 1.5 A @ 110Vac Nominal frequency (Hz) 50-60 Frequency variation range (Hz) 47-63 Input voltage range (Vrms) 90-270 Inrush current The maximum inrush current will be less than 50A and 100A when the adapter is connected to 115Vac and 230Vac respectively. Efficiency It should provide an efficiency of 80% minimum, when measured at maximum load under 115Vac. 1.
Power Management Power Saving Mode Standby Mode Enter Standby Mode when Phenomenon K K The buzzer beeps The Sleep indicator lights up K All power shuts off K The display shuts off 1.Standby/Hibernation hot-key is pressed and system is not ready to enter Hibernation mode. 2.System standby/ Hibernation timer expires and system is not ready to enter Hibernation mode. Hibernation Mode Enter Hibernation Mode (suspend to HDD) when 1.
Mechanical Specification Item I/O Ports Specification One type III PCMCIA (PC Card) port, one RJ-11 port, one RJ-45 port, one DC-in port, one ECP parallel port, four USB ports (two optional), two IEEE 1394 ports (optional)one line-in jack, one line-out jack, one speaker/headphone-out jack, one VGA port /I2 C compatible (optional).
I/O Address Map I/O Address Function 00000081-0000008F Direct memory access controller 00000090-0000009F Motherboard resources 000000A0-000000A1 Programmable interrupt controller 000000A4-000000A5 Motherboard resources 000000A8-000000A9 Motherboard resources 000000AC-000000AD Motherboard resources 000000B0-000000B5 Motherboard resources 000000B8-000000B9 Motherboard resources 000000BC-000000BD Motherboard resources 000000C0-000000DF Direct memory access controller 000000F0-000000FE Nu
IRQ Assignment Map Interrupt Channel Function NMI System errors IRQ0 System timer IRQ1 Keyboard IRQ6 Floppy IRQ8 Real time clock IRQ9 Microsoft ACPI-Compliant System IRQ11 Intel (R) 82801DB/DBM SMBus Controller-24C2 IRQ12 Synaptics PS2 pointing device IRQ13 Numeric data processor IRQ14 1st IDE device IRQ15 2nd IDE device IRQ16 Intel (R) 82801DB/DBM USB Universal Host Controller-24C2 IRQ16 Intel (R) 845G Graphics Controller IRQ17 Agere Systems AC’97 Modem IRQ17 Crystal WDM AC’9
Chapter 1 32
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press m during POST (while the TravelMate logo is being displayed).
PhoenixBIOS Setup Utility Information Main Advanced CPU Type System Memory Extended Memory HDD1 Serial Number System BIOS Version VGA BIOS Version KBC Version: Serial Number Asset Tag Number Product Name Manufacture Name UUID Number F1 Help Esc Exit 34 Select Item Select Menu Security Boot Exit Pentium (R) IV 1.4GHz 640 KB 121344 KB 115188 V0.51 (BXB35WW) 2759 02.29.
Multi-Boot Menu Users can press F12 during POST to enter the Multi Boot Selection Menu. In this menu users can change boot device without entering BIOS SETUP utility. Boot Menu 1. 2. 3. 4. +Removable Devices CD-ROM drive +Hard Drive D2D Recovery NOTE: If users disable the multi boot selection menu in BIOS SETUP utility, the message “ Press F12 to enter the multi boot selection menu” will not appear during POST.
System Information The System Information screen displays a summary of your computer hardware information. PhoenixBIOS Setup Utility Information Main Advanced CPU Type System Memory Extended Memory HDD1 Serial Number System BIOS Version VGA BIOS Version KBC Version: Serial Number Asset Tag Number Product Name Manufacture Name UUID Number F1 Help Esc Exit 36 Select Item Select Menu Security Boot Exit Mobile Intel (R) Celeron (R) CPU 1.60GHz 640 KB 121344 KB 115188 V0.51 (BXB35WW) 2759 02.
PhoenixBIOS Setup Utility Information Main Advanced CPU Type System Memory Extended Memory HDD1 Serial Number System BIOS Version VGA BIOS Version KBC Version: Serial Number Asset Tag Number Product Name Manufacture Name UUID Number F1 Help Esc Exit Select Item Select Menu Security Boot Exit Pentium (R) IV 1.4GHz 640 KB 121344 KB 115188 V0.51 (BXB35WW) 2759 02.29.
Main System Settings The Basic System Settings screen allows you to set the system date and time.
Parameter Description Format Boot on LAN When it is enabled, a remote host with an appropriate boot image can boot this computer via the internal LAN. Disabled or Enabled Hotkey Beep Help: Enable or disable hotkey beep. Enabled or Disabled Auto Dim Help: The system will support an automatic dimming of the Enabled or Disabled LCD backlight when the AC power is NOT available (running on battery power).
Advanced Information The Advanced Information screen contains parameter values that define how your computer behaves on system startup. PhoenixBIOS Setup Utility Information Main Advanced Security Boot Exit Legacy Diskette A: [1.44/1.
Parameter Legacy Diskette A Description Help: Selects floppy type. Note that 1.25MB 3 1/2” references a 1024 byte/sector Japanese media format. The 1.25MB, 3 1/2” diskette requires a 3Mode floppy-disk drive. Options 1.44/1.25MB 3 1/2” or Disabled Enable or Disable Legacy Diskette A Primary Master Show IDE Primary Master HDD size. User can enter submenu to set some detail functions Secondary Master Show IDE Secondary Master Device Status. User can enter submenu to set some detail functions.
Primary Master The Primary Master sub-menu contains parameters related to the primary hard disk. CAUTION: The parameters in this screen are for the advanced users only. Typically, you do not need to change the values in this screen.The default setting of Auto optimizes all the settings for your hard disk. PhoenixBIOS Setup Utility Advanced Prim ary Master Type: [10056MB] Item Specific Help User= you enter parameters of hard-disk drive installed at this connection.
Secondary Master The Secondary Master sub-menu contains parameters related to the Media bay drive. CAUTION: The parameters in this screen are for the advanced users only. Typically, you do not need to change the values in this screen. The default setting of Auto optimizes all the settings for your Media bay drive. PhoenixBIOS Setup Utility Advanced Secondary Master Type: [20004MB] Item Specific Help User= you enter parameters of hard-disk drive installed at this connection.
I/O Device Configuration The parameters in this screen are for advanced users only. You do not need to change the values in this screen because these values are already optimized. The I/O Device Configuration screen assigns resources to basic computer communication hardware.
PCI IRQ Routing The PCI IRQ Routing sub-menu allows you to set IRQ for PCI devices. CAUTION: The parameters in this screen are for advanced users only. Typically, you do not need to change the values in this screen because these values are already optimized.
System Security The System Security screen contains parameters that help safeguard and protect your computer from unauthorized use. PhoenixBIOS Setup Utility Information Main Advanced Security Set Supervisor Password Set User Password [Enter] [Enter] Password on boot [Enabled] Set Primary Hard Disk Password [Enter] F1 Help Esc Exit Select Menu Select Item Boot Exit Item Specific Help Supervisor password controls the access of the whole setup utility.
Set Supervisor Pass w ord Enter N ew Pas sw ord [ C onfirm N ew P assw ord [ 2. ] ] e Type a password. The password may consist of up to eight characters (A-Z, a-z, 0-9) and then press . IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen. 3. Retype password to verify your first entry and then press e. The following screen appears: S e tu p N o tice C h an g e s h a ve b ee n sa v ed . [C o n tin u e] 4. 5. 6.
Type the Supervisor Password and press 2. m e to access the BIOS Utility. When the User Password is set and Power on boot is set enabled, the following prompt appears at bootup when pressing . Enter Password e to use the computer. e. Type the User Password (a symbol appears for each character you type) and press If you enter the password incorrectly, an x symbol appears. Try again and press 3. When the Power on boot is set enabled, the following prompt appears at boot-up. Enter Password 4.
Boot Options Users can press F12 during POST to enter the Boot Options Menu. In this menu users can change boot device without entering BIOS SETUP utility. PhoenixBIOS Setup Utility Information Main Advanced Security Boot +Removable Devices +Hard Drive CD-ROM Drive D2D Recovery Exit Item Specific Help Keys used to view or configure devices: expands or collapses devices and moves the device up or down.
Exit Setup This menu contains exit options. PhoenixBIOS Setup Utility Information Main Advanced Security Boot Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit Item Specific Help Exit System Setup and save your changes to CMOS. F1 Help Esc Exit Select Item Select Menu F5/F6 Change Values F9 Setup Defaults Enter Select > Sub-Menu F10 Save and Exit The following table describes the parameters in this screen.
D o yo u w an t to lo ad de fault setting s? [Yes] [N o] e If you would like to load factory- default settings for all parameters, use the cursor then press Chapter 2 . Choose No if otherwise.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: K K New versions of system programs New features or options Use the WFlash utility to update the system BIOS flash ROM. Executing the Flash Program Please do the following to update BIOS. To update BIOS: 1. Prepare the BIOS Flash Diskette a. 52 Prepare the BIOS Flash Package. 2. Unzip this package 3. Run Update.bat 4. The system will ask you to reboot the computer after the BIOS is updated.
System Utility Diskette This utility diskette is for the TravelMate 230/ 280 notebook machine. You can find the utility in Service CD kit. It provides the following functions: 1. Panel ID Utility 2. 1394 GUID Utility 3. Mother Board Data Utility To use this diskette, first boot from this diskette, then a “Microsoft Windows ME Startup Menu” prompt you to choose the testing item. Follow the instructions on screen to proceed. NOTE: This program contains a readme.txt file. This readme.
System Diagnostic Diskette IMPORTANT: 1The diagnostics program here that we used is called PQA (Product Quality Assurance) and is provided by Headquarters. You can utilize it as a basic diagnostic tool. To get this program, you can find it in the service CD kit. To better fit local service requirements, your regional office MAY have other diagnostic program. Please contact your regional offices or the responsible personnel/channel to provide you with further technical details.
Running PQA Diagnostics Program To run the program, simply type: PQA and press e . The main menu appears on screen. PQA Vx_x Result Diag zx SysInfo Press / to move around the main menu. Press are Diag, Result, SysInfo, Option and Exit. Option e xx-xx-xx Exit to enable the selected option. The main options The Diag option lets you select testing items and times. The following screen appears when you select Diag from the main menu.
The screen below appears if you select Multi Test. PQA PQA Diag Diag Vx_x Vx_x Result Result Diag Diag ONE One MULTI Multi FULL QUICK SysInfo SysInfo xx-xx-xx xx-xx-xx Option Option Exit Exit TEST TEST TEST TEST TEST TEST TEST COUNT VALUE (1...9999) 1 Specify the desired number of tests and press e . After you specify the number of tests to perform, the screen shows a list of test items (see below).
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: K K K K K K Wrist grounding strap and conductive mat for preventing electrostatic discharge Number 1 Flat-bladed screwdriver Phillips screwdriver Tweezers Plastic Flat-bladed screwdriver Number 5 Hexed screwdriver NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 58 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system.
Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
LCD Module 3 LCD Cushions Ax3 LCD Bezel Gx1 for 15” LCD Gx2 for 14.1” LCD Inverter Hx6 for Hitachi 15” Super XGA+ LCD Unit Gx4 for 14”1 XGA LCD Unit Cx6 for Hitachi 15” XGA LCD Unit LCD LCD Panel Ox4 for 14.
Screw List Item Description A Screw M2.5XL6 Flat Head (Black) B Screw M2XL3 Washer Flat Head (Black) C Screw M2XL4 Flat Head (Black) D Screw M2XL4 Round Head (Black) E Screw M2XL5 Round Head (Silver) F Hex Screw G Screw M2.5XL4 Flat Head (Silver) H Screw M2XL4.
Removing the Battery 1. 62 To remove the battery, push the battery release button, and then slide the battery out from the machine.
Removing the Hard Disk Drive Module 1. See “Removing the Battery” on page 62 2. To remove the hard disk drive, first remove the one screw from the hard disk drive cover, and then remove the cover. 3. Remove the two screws as shown and then pull the plastic tag to detach the hard disk drive module out from the machine carefully. NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive module to the main unit.
4. Detach the hard disk drive from the hard disk drive bracket. NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the hard disk drive bracket to the hard disk drive module. It is suggested that you reverse the sequence when you remove the screws.
Removing the Memory Module 1. See “Removing the Battery” on page 62 2. To remove the memory module from the machine, first remove the two screws from the memory cover. 3. Lift the cover off, then remove the memory cover. 4. Push out the latches on both sides of the socket and pull the memory module out from the socket.
Removing the Modem Board 1. See “Removing the Battery” on page 62 2. To remove the modem board, first remove the screw from the modem cover. 3. Remove the modem cover from the machine. 4. Remove two screws from the modem board as shown, then remove the modem board from the main unit carefully by using a plastic bladed screw driver. 5. Disconnect the modem cable from the modem board, then remove the modem board.
Chapter 3 67
Disassembling the LCD Removing the Middle Cover 1. See “Removing the Battery” on page 62 2. To remove the middle cover, first remove the two screws from the rear of the unit and then pry up the middle cover with a plastic flat screwdriver in the way as shown. 3. Disconnect the launch board cable from the launch board and then detach the middle cover away from the main unit. . Removing the Launch Board 68 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3.
Removing the Keyboard 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. To remove the keyboard, first pull out and upward to expose the keyboard. 4. Use a plastic flat screwdriver to help disconnect the keyboard cable from the main board carefully, then remove the keyboard from the main board. Removing the CD-ROM Drive Module 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3.
Disassembling the CD-ROM Drive Module 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the CD-ROM Drive Module” on page 69 5. To disassemble the CD-ROM drive module, first remove two screws as shown. 6. Remove the CD-ROM drive bracket from the CD-ROM drive module. NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the CD-ROM drive bracket to the CDROM drive module.
NOTE: 1.Because the CD-ROM module and the heat plate share the common screw, you only have to remove the two screws as shown below If you detach the heat plate from the main unit after the step of removing the CD-ROM. The same principle applies to the assembly procedures. NOTE: 2.Please follow the numeric orders such as 1, 2, 3, and 4 to screw the heat plate to the main unit. It is suggested that you reverse the sequence when you remove the screws. Removing the LCD Module 1.
7. Remove the inverter cable from the main board with a plastic flat screwdriver. 8. Remove the LCD module from the main unit carefully. 9. Disconnect the launch board cable from the main board and remove it. NOTE: Please arrange the inverter cable and the coaxial cable well in the way as shown after you connect them to the main board.
Removing the LCD Bezel 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. Use plastic tweezers to remove the three LCD cushions on the LCD bezel, and then remove the three screws below from the LCD bezel. 7. Snap off the bezel carefully, and then remove the LCD bezel from the LCD module.
Removing the Inverter Board (14.1” LCD) 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. See “Removing the LCD Bezel” on page 73 7. To remove the inverter board, first remove two screws from the inverter board. 8. Disconnect the LCD power cable and the inverter cable from the inverter board. NOTE: 1.
Removing the Inverter Board (15” LCD) 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. See “Removing the LCD Bezel” on page 73 7. To remove the inverter board, first remove one screw from the inverter board. 8. Disconnect the LCD power cable and the inverter cable from the inverter board.
Removing the 14.1” TFT LCD 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. See “Removing the LCD Bezel” on page 73 7. See “Removing the Inverter Board (14.1” LCD)” on page 74 8. To remove the LCD, first remove the four screws from the LCD, then remove the LCD from the LCD panel.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the LCD to the LCD panel. It is suggested that you reverse the sequence when you remove the screws. Removing the 14.1” TFT LCD Brackets 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. See “Removing the LCD Bezel” on page 73 7.
suggested that you reverse the sequence when you remove the screws. Removing the LCD Coaxial Cable 78 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the LCD Module” on page 71 6. See “Removing the LCD Bezel” on page 73 7. See “Removing the Inverter Board (14.1” LCD)” on page 74 8. See “Removing the Inverter Board (15” LCD)” on page 75 9.
Disassembling the Main Unit Removing the RTC Battery 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. Disconnect the RTC cable and then remove the RTC battery from the upper case gently. Removing the Touch Pad Frame 1. See “Removing the Battery” on page 62 2. Use a plastic flat screwdriver to pry up the touch pad frame very carefully. 3.
5. Remove the other screw from the base of the unit, then remove the fan from the lower case. Removing the CPU Heat Sink 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the Audio Board” on page 85 6. Remove four screws and then detach the CPU heat sink from the main unit.
2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 5. See “Removing the Audio Board” on page 85 6. See “Removing the CPU Heat Sink” on page 80 7. Use a flat screwdriver to unlock the CPU socket counter clockwise, detach the CPU from its socket and then lock the CPU socket clockwise with the flat screwdriver. Installing the Processor 1. See “Removing the Battery” on page 62 2.
3. See “Removing the Middle Cover” on page 68 4. See “Removing the Keyboard” on page 69 5. See “Removing the CD-ROM Drive Module” on page 69 6. See “Removing the Heat Plate” on page 70 7. See “Removing the LCD Module” on page 71 8. See “Removing the RTC Battery” on page 79 9. Use a plastic flat screwdriver to disconnect the touch pad cable from the main board. 10. To remove the upper case, first remove the nine screws from the base of the unit as shown. 11.
Removing the Touch Pad Board 1. See “Removing the Battery” on page 62 2. See “Removing the Touch Pad Frame” on page 79 3. See “Removing the Upper Case” on page 81 4. To detach the touch pad board, first disconnect the touch pad cable from the touch pad board with a plastic flat screwdriver and plastic tweezers, and then remove the touch pad board from the upper case. Removing the Touch Pad Button 1. See “Removing the Battery” on page 62 2. See “Removing the Touch Pad Frame” on page 79 3.
Removing the Touch Pad Cable 1. See “Removing the Battery” on page 62 2. See “Removing the Touch Pad Frame” on page 79 3. See “Removing the Upper Case” on page 81 4. See “Removing the Touch Pad Board” on page 83 5. See “Removing the Touch Pad Button” on page 83 6. See “Removing the Touch Pad Scroll Key” on page 83 7. Remove the touch pad cable from the main board carefully. 8. Detach the touch pad cable from the upper case carefully. Removing the Floppy Disk Drive Module 1.
11. Detach the FDD module from the lower case. NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the FDD module to the main board. It is suggested that you reverse the sequence when you remove the screws. Removing the Audio Board 1. See “Removing the Battery” on page 62 2. See “Removing the Hard Disk Drive Module” on page 63 3. See “Removing the Middle Cover” on page 68 4. See “Removing the Keyboard” on page 69 5. See “Removing the CD-ROM Drive Module” on page 69 6.
Removing the Speakers 1. See “Removing the Battery” on page 62 2. See “Removing the Hard Disk Drive Module” on page 63 3. See “Removing the Middle Cover” on page 68 4. See “Removing the Keyboard” on page 69 5. See “Removing the CD-ROM Drive Module” on page 69 6. See “Removing the Heat Plate” on page 70 7. See “Removing the LCD Module” on page 71 8. See “Removing the RTC Battery” on page 79 9. See “Removing the Upper Case” on page 81 10.
7. See “Removing the LCD Module” on page 71 8. See “Removing the RTC Battery” on page 79 9. See “Removing the Upper Case” on page 81 10. To remove the charger plate, first remove the screw from the charger plate, and then remove the charger plate from the main board. Removing the Main Board 1. See “Removing the Battery” on page 62 2. See “Removing the Hard Disk Drive Module” on page 63 3. See “Removing the Middle Cover” on page 68 4. See “Removing the Keyboard” on page 69 5.
NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the main board to the lower case. It is suggested that you reverse the sequence when you remove the screws. Removing the PCMCIA Slot 1. See “Removing the Battery” on page 62 2. See “Removing the Hard Disk Drive Module” on page 63 3. See “Removing the Middle Cover” on page 68 4. See “Removing the Keyboard” on page 69 5. See “Removing the CD-ROM Drive Module” on page 69 6. See “Removing the Heat Plate” on page 70 7.
NOTE: 1. Please follow the numeric orders such as 1, 2, 3, and 4 to screw the PCMCIA plate to the main board. It is suggested that you reverse the sequence when you remove the screws. 2. Please note that the I/O port bracket should be attached to the main board before assembling the PCMCIA slot to the main board. Removing the I/O Port Bracket 1. See “Removing the Battery” on page 62 2. See “Removing the Hard Disk Drive Module” on page 63 3. See “Removing the Middle Cover” on page 68 4.
17. Detach the I/O port bracket from the main board. NOTE: Please follow the numeric orders such as 1, 2, 3, and 4 to screw the I/O port to the main board. It is suggested that you reverse the sequence when you remove the screws.
System Upgrade Procedure Base Unit to Wireless Unit 1. See “Removing the Battery” on page 62 2. See “Removing the Middle Cover” on page 68 3. See “Removing the Keyboard” on page 69 4. See “Removing the Heat Plate” on page 70 (Remove three screws here) 5. Note that the one with the white RF cable is for the right antenna and the one with the black RF cable is for the left antenna. 6. Insert the wireless LAN board into its socket and press it down to secure well. 7.
9. Be careful to arrange the right and left RF cables well. 10. Connect the RF cables into the Wireless LAN board. NOTE: Please note that the black RF cable should be routed beneath the coaxial cable.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. See “System Diagnostic Diskette” on page 54 for details. 1.
Keyboard or Auxiliary Input Device Check Remove the external keyboard if the internal keyboard is to be tested. If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board. If the keyboard cable connection is correct, run the Keyboard Test. See “System Diagnostic Diskette” on page 54 for details.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: K K K Replace the System board. If the problem is not corrected, see “Undetermined Problems” on page 106. If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes 006 Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error 3. IDE Secondary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 Incorrect password specified, system disabled.
Error Message List Error Messages Real time clock error FRU/Action in Sequence RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility. RTC battery System board Memory size found by POST differed from CMOS Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages FRU/Action in Sequence No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 95. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 95.
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error LCD backlight doesn't work Action in Sequence LCD is too dark Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. LCD brightness cannot be adjusted Reconnect the LCD connectors. LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't work).
PCMCIA-Related Symptoms Symptom / Error Action in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly PCMCIA slot pin is damaged. PCMCIA slot assembly System board Memory-Related Symptoms Symptom / Error Memory count (size) appears different from actual size. Action in Sequence Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system.
Power Management-Related Symptoms Symptom / Error System hangs intermittently. Action in Sequence Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / Error System configuration does not match the installed devices. Action in Sequence Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system. Reconnect hard disk/CD-ROM/diskette drives. External display does not work correctly.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 95): 1.
Index of Phlash16 Error Message Error Codes Error Message -1 or // FF Memory allocation for Backup file buffer failed. -2 or // FE BIOS.BAK already exists (rename or delete it) -3 or // FD File Create failed on BIOS.BAK -4 or // FC File Write failed on BIOS.BAK -5 or // FB File Close failed on BIOS.BAK -6 or // FA BIOS backup not supported in BIOS ROM file. -7 or // F9 File Open failed on BIOS ROM file. -8 or // F8 File Read failed on BIOS ROM file.
Error Codes 108 Error Message -44 or // D4 Cannot flash if Memory Managers (e.g.HIMEM) is present. -45 or // D3 BIOS ROM file maybe corrupt (checksum not zero). -46 or // D2 BIOS ROM file size doesn’t match flash part size. -47 or // D1 DMI system and chassis strings require BCP DMI 2.1+. -48 or // D0 BIOS ROM file is older than (or same as) BIOS ROM image. -49 or // CF Platform signature not found in the interface. -50 or // CE Device descriptor signature not found in the interface.
Index of PQA Diagnostic Error Code, Message Error Code Message 01XXX CPU or main board error 02XXX Memory error Action in Sequence Reload BIOS default setting.
110 TravelMate 230/ 280
Chapter 5 Jumper and Connector Locations Top View PCB No.
CN11 LCD Coaxial Cable Connector SW1 SW1 Setting (Please see below) CN12 Fan Connector U18 CPU Socket CN13 RTC Battery Connector U34 Golden Finger (or Debug Board) Keyboard Switch Settings SW1-1 SW1-2 English OFF OFF Japanese ON OFF Europe ON ON Password Bypass Setting and BootBlock Setting SW1-3 112 SW1-4 Check Password Enable ON OFF BootBlock Enable OFF ON TravelMate 230/ 280
Bottom View CN21 Modem Card Cable Connector U65 North Bridge (845-GL) CN22 Audio Board Connector U68 Cardbus Controller (OZ6912T) CN23 Battery Connector U77 South Bridge (ICH4) CN24 Modem Connector DM1 DIMM 1 Socket U55 LVDS DM2 DIMM 2 Socket U62 LAN Controller (RTL8100BL) Chapter 5 113
114 TravelMate 230/ 280
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 230/ 280. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
TravelMate 230 Exploded Diagram 116 TravelMate 230/280
Picture No. Partname Description Cables Chapter 6 NS LCD COAXIAL CABLE 14.1" XGA CABLE LCD COAXIAL 14.
Picture No.
Picture Chapter 6 No. Partname Description 12 MODEM COVER W/SCREW ASSEMBLY MODEM COVER PELICAN NS CD-ROM BRACKET BRACKET CD ROM PELICAN 10 UPPER CASE W/ TOUCHPAD MODULE ASSEMBLY UPPER CASE PELICAN NS TOUCHPAD COVER FRAME TOUCHPAD PELICAN 11 MIDDLE COVER W/O LAUNCH BOARD COVER MIDDLE PELICAN NS LCD BEZEL 14.1" W/ NAME PLATE & RUBBER ASSEMBLY BEZEL 14.1" NS LCD PANEL W/ HINGE BRACKET, LATCH & LOGO ASSEMBLY PANEL 14.
Picture No. Partname Description 1 LOWER CASE W/ DIMM COVER & SPEAKER PACK ASSEMBLY LOWER CASE PELICAN NS DIMM COVER W/ SCREW ASSEMBLY DIMM COVER PELICAN NS PCMCIA SLOT CONN CARDPUSH 1CA91501-TC-F2 NS I/O BRACKET ASSEMBLY I/O BRACKET PELICAN NS PCMCIA PLATE ASSEMBLY PCMCIA PLATE PELICAN NS AUDIO BOARD PELICAN AUDIO BD (SMT) VER-0SA NS INVERTER BOARD 14"/15"AMBIT INVERTER 14"/15" T62I223.
Picture No. 8 Partname Description MODEM BOARD AMBIT T60M283.00 MODEM MDC AMB/T60M283.00 NS LAUNCH BOARD PELICAN LAUNCH KEY BD NS WIRELESS BOARD AMBIT T60H656.00 LAN WLESS PCI AMBIT T60H656.
Picture No.
Picture No. Partname Description 15 FDD MODULE 1.
Picture No. Partname Description NS SCREW RUBBER UPPER RUBBER UP 14.1" BEZEL F3M NS SCREW RUBBER LOWER RUBBER SCREW DOWN F3M NS NAME PLATE FOR BEZEL MYLAR NAME PLATE PELICAN NS LOGO LABEL FOR PANEL LABEL LOGO ON PANEL PELICAN NS NAME PLATE FOR MIDDLE COVER TM230 MYLAR PLATE NAME COVER MIDDLE NS LAUNCH KEY KEY LAUNCH PELICAN NS SCREW SCR. HEX NUT W/WASHER&NYLOK #4 NS SCREW SCREW M2L12 PH MSN+BZ 21 SCREW SCREW CPU MECH WAFER M2*L4 NI 23 SCREW SCREW M2.
TravelMate 280 Exploded Diagram Chapter 6 125
Picture No.
Picture No.
Picture 128 No.
Picture No. Partname Description NS PCMCIA SLOT CONN CARDPUSH 1CA91501-TC-F2 NS I/O BRACKET ASSEMBLY I/O BRACKET PELICAN NS PCMCIA PLATE ASSEMBLY PCMCIA PLATE PELICAN NS AUDIO BOARD PELICAN AUDIO BD (SMT) VER-0SA NS INVERTER BOARD 14"/15"AMBIT INVERTER 14"/15" T62I223.00 8 MODEM BOARD AMBIT T60M283.00 MODEM MDC AMB/T60M283.
Picture No.
Picture No. Partname Description NS ADAPTER 70W 3PIN DELTA ADP65DBBE ADT 70W ADP-65DBBE 3P NS KEYBOARD NSK-84X21 US KB US NSK-84X21 NS SPEAKER PACK LEFT/RIGHT SPEAKER PELICAN 3 CPU HEATSINK SINK HEAT CPU PELICAN 17 CPU FAN SINK W/ FAN ASSEMBLY FAN PELICAN 15 FDD MODULE 1.
Picture No. Partname Description NS COMBO DRIVE 8/24/10/24X KME UJA74OAC6 F4 COMBO 8,24/10/24 UJA74OAC6 F4 9 MAINBOARD PELICAN W/ COIN BATTERY, I/O BRACKET, MODEM CABLE, PCMCIA PLATE & PCMCIA SLOT PELICAN MB (DIP) W/O CPU VER-SB NS TOUCHPAD BUTTON SCROLL BUTTON TOUCHPAD SCROLL NS TOUCHPAD BUTTON PAD BUTTON TOUCHPAD PELICAN NS SCREW RUBBER UPPER RUBBER UP 14.
Picture No. Partname Description NS LOGO LABEL FOR PANEL LABEL LOGO ON PANEL PELICAN 4 NAME PLATE FOR MIDDLE COVER TM280 MYLAR PLATE NAME TM280 MIDDLE 21 SCREW SCREW CPU MECH WAFER M2*L4 NI 23 SCREW SCREW M2.0*12 STEEL B 24 SCREW SCREW M2L4 BH MSN+BZ 25 SCREW SCREW M2L5 BH MSN+N NS SCREW SCREW M2*3 NYLON 1JMCPC420325 26 SCREW SCREW 27 SCREW SCREW M2.5X6 NS SCREW SCREW M3x4(86.9A524.4R0) NS SCREW SCREW WAFER NYLOK NI 2ML3 NS SCREW SCREW M2.
134 TravelMate 230/280
Appendix A Model Definition and Configuration Model Number Definition Model Number LCD CPU Memory HDD CD/DVD 230X 14.1” TFT Celeron 1.7G 128/256MB 20GB 230FX 14.1” TFT Celeron 1.7G 128MB 20GB 24X CD-ROM Li-ion 230XV 14.1” TFT Celeron 1.7G 128/256MB 20GB/ 30GB 8X DVD-ROM Li-ion 230FXV 14.1” TFT Celeron 1.7G 128MB 20GB 8X DVD-ROM Li-ion 230XC 14.1” TFT Celeron 1.7G 256MB 30GB Combo Li-ion 230LC 15” TFT Celeron 1.7G 256MB 30GB Combo Li-ion 231X 14.
136 TravelMate 230/ 280
Appendix B Test Compatible Components This computer’s compatibility is a test plan released by Acer Internal Testing Department. Once the final report is available, this chapter will be revised accordingly.
Microsoft Windows XP Environment Test Item Processor Specifications Intel Pentium IV Northwood 1.7 GHz, Intel Pentium IV Northwood 1.8 GHz, Intel Pentium IV Northwood 1.9 GHz, Intel Pentium IV Northwood 2.0 GHz, Intel Pentium IV Northwood 2.1 GHz, Intel Pentium IV Northwood 2.2 GHz, Intel Celeron Northwood 1.6 GHz, Intel Celeron Northwood 1.7 GHz, Intel Celeron Northwood 1.8 GHz, Intel Celeron Northwood 1.9 GHz, Intel Celeron Northwood 2.
Item Specifications CD-ROM Drive Mitsumi SR-244W1 DVD/CD-RW Combo KME UJDA740 AC Adapter (3 pin) Delta 70W Liteon 70W Power Cord Battery Li-Ion, 8 cells King Cord Samsung, Li-Ion 8cells Sanyo, Li-Ion 8cells Network Adapters LAN Ethernet/10baseT/100baseT 3Com Etherlink III 3C589D IBM EtherJet CardBus Adapter 10/100 Intel Ether Express Pro/100 Mobile Adapter MBLA3200 Xircom CardBus Ethernet 10/100 32 Bit CBE-10/100BTX Multifunction Card (Combo) 10/100 EtherJet CardBus Real Port w/ 56K modem 34L13
Item I/O - USB Keyboard/Mouse Specifications Chicony USB Keyboard IBM USB Numeric Keypad Microsoft Natural Keyboard Pr Acer Aspire USB mouse Logicool US Mouse Logitech Cordless Mouseman Wheel USB Interface Logitech USB Wheel Mouse Microsoft IntelliMouse Optical USB Interface I/O - USB (Printer/Scanner) Epson Stylus Color 740 USB interface HP DeskJet 880C USB interface Canon CanonScan D1250 (USB 2.
Item PCMCIA - ATA Specifications IBM Microdrive 340MB IBM Microdrive 1G Iomega Click! 40MB PCMCIA - USB 2.0 Apricorn EZ-USB2.
Microsoft Windows 2000 Environment Test Item Processor Specifications Intel Pentium IV Northwood 1.7 GHz, Intel Pentium IV Northwood 1.8 GHz, Intel Pentium IV Northwood 1.9 GHz, Intel Pentium IV Northwood 2.0 GHz, Intel Pentium IV Northwood 2.1 GHz, Intel Pentium IV Northwood 2.2 GHz, Intel Celeron Northwood 1.6 GHz, Intel Celeron Northwood 1.7 GHz, Intel Celeron Northwood 1.8 GHz, Intel Celeron Northwood 1.9 GHz, Intel Celeron Northwood 2.
Item Specifications CD-ROM Drive Mitsumi SR-244W1 DVD/CD-RW Combo KME UJDA740 AC Adapter (3 pin) Delta 70W Liteon 70W Power Cord Battery Li-Ion, 8 cells King Cord Samsung, Li-Ion 8cells Sanyo, Li-Ion 8cells Network Adapters LAN Ethernet/10baseT/100baseT 3Com Etherlink III 3C589D IBM EtherJet CardBus Adapter 10/100 Intel Ether Express Pro/100 Mobile Adapter MBLA3200 Xircom CardBus Ethernet 10/100 32 Bit CBE-10/100BTX Multifunction Card (Combo) 10/100 EtherJet CardBus Real Port w/ 56K modem 34L13
Item I/O - USB Keyboard/Mouse Specifications Chicony USB Keyboard IBM USB Numeric Keypad Microsoft Natural Keyboard Pr Acer Aspire USB mouse Logicool US Mouse Logitech Cordless Mouseman Wheel USB Interface Logitech USB Wheel Mouse Microsoft IntelliMouse Optical USB Interface I/O - USB (Printer/Scanner) Epson Stylus Color 740 USB interface HP DeskJet 880C USB interface Canon CanonScan D1250 (USB 2.
Item PCMCIA - ATA Specifications IBM Microdrive 340MB IBM Microdrive 1G Iomega Click! 40MB PCMCIA - USB 2.0 Apricorn EZ-USB2.
Microsoft Windows 98 Environment Test Item Processor Specifications Intel Pentium IV Northwood 1.7 GHz, Intel Pentium IV Northwood 1.8 GHz, Intel Pentium IV Northwood 1.9 GHz, Intel Pentium IV Northwood 2.0 GHz, Intel Pentium IV Northwood 2.1 GHz, Intel Pentium IV Northwood 2.2 GHz, Intel Celeron Northwood 1.6 GHz, Intel Celeron Northwood 1.7 GHz, Intel Celeron Northwood 1.8 GHz, Intel Celeron Northwood 1.9 GHz, Intel Celeron Northwood 2.
Item Specifications CD-ROM Drive Mitsumi SR-244W1 DVD/CD-RW Combo KME UJDA740 AC Adapter (3 pin) Delta 70W Liteon 70W Power Cord Battery Li-Ion, 8 cells King Cord Samsung, Li-Ion 8cells Sanyo, Li-Ion 8cells Network Adapters LAN Ethernet/10baseT/100baseT 3Com Etherlink III 3C589D IBM EtherJet CardBus Adapter 10/100 Intel Ether Express Pro/100 Mobile Adapter MBLA3200 Xircom CardBus Ethernet 10/100 32 Bit CBE-10/100BTX Multifunction Card (Combo) 10/100 EtherJet CardBus Real Port w/ 56K modem 34L13
Item I/O - USB Keyboard/Mouse Specifications Chicony USB Keyboard IBM USB Numeric Keypad Microsoft Natural Keyboard Pr Acer Aspire USB mouse Logicool US Mouse Logitech Cordless Mouseman Wheel USB Interface Logitech USB Wheel Mouse Microsoft IntelliMouse Optical USB Interface I/O - USB (Printer/Scanner) Epson Stylus Color 740 USB interface HP DeskJet 880C USB interface Canon CanonScan D1250 (USB 2.
Item PCMCIA - ATA Specifications IBM Microdrive 340MB IBM Microdrive 1G Iomega Click! 40MB PCMCIA - USB 2.0 Apricorn EZ-USB2.
150 TravelMate 230/280
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
152 TravelMate 230/ 280
Index A I/O voltage 18 package 18 type 18 AC Adapter 27 Audio 18 D B DC-AC LCD Inverter 26 Battery 25 DC-DC/Charger 25 battery pack DIMM 19 Combinations 19 package 19 Speed 19 voltage 19 charging indicator 12 BIOS 18 package 18 ROM size 18 ROM type 18 vendor 18 Version 18 Disassembly Machine 57 Disassembly Flowchart 59 BIOS Setup Utility 33 Display 2 BIOS Supports protocol 18 display BIOS Utility 33 hotkeys 15 Load Default Settings 50 Navigating 35 System Information 36 System Security 45
hotkey 15 parallel port Hot Keys 15 setting in BIOS Utility 44 Password Setting I Hard Disk Password 47 Power-On Password 47 Setup Password 47 I/O Address Map 29 Indicators 12 PC Card 12, 25 Intermittent Problems 105 PCMCIA 25 IRQ Assignment Map 31 Power Management 28 J Power management 2 Power System Check 95 Jumper and Connector Locations Battery Pack 97 Power Adapter 96 Bottom View 113 SW2 Settings 112 Top View 111, 113 PQA 54 Processor 18 K R Keyboard 18, 25 Removing the Battery Pack
V Video 24 Resolutions 24 Video controller 18 W Windows 2000 Environment Test 142 Windows 98 Environment Test 146 Windows XP Environment Test 138 Index 155
156 TravelMate 230/ 280
