ACE PLUS CORP. Wall Plate Series EX-G019 HDMI 1.3 over CAT5 Wall Plate Extender with IR Control Path User Manual Page 1 of 10 Headquarters : 9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian, Taipei, Taiwan 231 TEL: +886-2-2912-4201 FAX: +886-2-2912-3164 Website: www.ace-plus.
ACE PLUS CORP. Safety and Notice The EX-G019 HDMI 1.3 over CAT5 Wall Plate Extender with IR Control Path has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the EX-G019 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. z Follow all instructions and warnings marked on this unit.
ACE PLUS CORP. Introduction The EX-G019 HDMI 1.3 over CAT5 Wall Plate Extender with IR Control Path wall plate edition boosts up your video/audio transmission distance up to 60m [200ft] in HDTV 720p/1080i format. With two low cost CAT-5/5e/6 LAN cables, users can readily extend HDTV sources from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display monitors including HDMI enabled TV sets, LCD PC monitors, or projectors.
ACE PLUS CORP. Specifications & Package Contents Model Name Technical Role of usage HDMI compliance HDCP compliance Video bandwidth Video support Transmission length over LAN cable Audio support Equalization ESD protection PCB stack-up Input TMDS signal Input DDC signal Input Output CEC Bypass HDMI source control IR remote control HDMI connector RJ-45 connector 3.
ACE PLUS CORP. Panel Descriptions Front View — Transmitting Unit [EX-G019-TX] IR EXTENDER HDMI IN HDMI IN: Connect to a HDMI source with a HDMI M-M cable here. IR EXTENDER: Extendable infrared sending socket for plugging in the extension cable of IR emitter\ Push button: Select CEC or IR transmission (Must be consistent with RX unit).
ACE PLUS CORP. Front View — Receiving Unit [EX-G019-RX] IR EXTENDER HDMI OUT EQ HDMI OUT: Connect to a HDMI display with a HDMI M-M cable here. EQ: Adjust the 8-level equalization control to the received HDMI signals. 0 – 7 = strongest – weakest. It is recommended to switch from 7 to 0 to find the optimal visual experience. IR EXTENDER: Extendable infrared reception socket for plugging in the extension cable of IR receiver. Push button: Select CEC or IR transmission (Must be consistent with TX unit).
ACE PLUS CORP. IR Control Path IR Cables IR Emitter Cable IR Receiver Cable IR Sockets EX-G019-TX IR Extender: Plug in the IR emitter cable here to transmit all IR command signals received from the IR receiver. EX-G019-RX IR Extender: Plug in IR receiver cable connected here to receive all IR command signals from the IR remote control of the HDMI source machine.
ACE PLUS CORP. Supported IR Data Format Data Format Suitable NEC RC5 TOSHIBA MICOM CODE GRUNDIG CODE SONY 12 BIT CODE SONY 15 BIT CODE SONY 20 BIT CODE RCA CODE RCM CODE MATSUSHITA CODE MITSUBISHI CODE ZENITH CODE JVC CODE M50560-001P MN6125H MN6125L MN6014_C5D7 MN6014-C6D6 MC14457P LC7464(AHEA) GEMINI_CM 5 5 Not Recommended 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Hardware Installation 1. Connect your HDMI / DVI source (such as a DVD player) to the transmitting unit EX-G019-TX. 2.
ACE PLUS CORP. Notice 1. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C. 2. The transmission length is largely affected by the type of LAN cables, the type of HDMI sources, and the type of HDMI display. The testing result shows solid LAN cables (usually in bulk cable 300m/1000ft form) can transmit a lot longer signals than stranded LAN cables (usually in patch cord form).
ACE PLUS CORP. Limited Warranty The SELLER warrants the EX-G019 HDMI 1.3 over CAT5 Wall Plate Extender with IR Control Path to be free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer.
