Datasheet

ManualsBrandsACCUCELL ManualsPhoto/Video Batteries & PSUsCamera battery replaces original battery 3.7 V

APPROVAL SHEET

FOR

40698 BATTERY

Date: 2018-2-27

To:

Model No.: 40698 / SLB1137D

Specification: 3.7V /1100mAh

Total No. of Pages: Total 13 pages including this cover sheet

Approved by

Presented by

Written

滕建军

Project checked

杨平

Quality checked

滕金莲

R&D checked

雷钢

Approval

Section

Confirm

checked

Approval

Name

Approve

Summary of content (13 pages)

PAGE 1
APPROVAL SHEET FOR 40698 BATTERY Date: 2018-2-27 To: Model No.: 40698 / SLB1137D Specification: 3.7V /1100mAh Total No.
PAGE 2
Model 40698 /SLB1137D Execution date Edition explain Written 2016-7-11 2 edition no. A1.
PAGE 3
1. Scope: This Data Sheet described the specification, testing method, type and model no. of Lithium-ion Battery. 1.1 Type: Digital camera battery 1.2 Model NO.: 40698 2: Battery Item 1 2 3 4 5 6 Rated Voltage Performance 3.7V Charge limited voltage 4.2V Discharge-off voltage 2.75V Rated Capacity Minimum Capacity Charging Method Remarks 1100mAh Discharge at 0.2C 1045mAh Discharge at 0.2C CC-CV 7 Standard Charging Current 0.22Ah 0.2C 8 Standard Discharge Current 0.22Ah 0.
PAGE 4
Range Instruction： 1. Storage time should be counted from the time of Delivery； 2. Test Method & Standard: The battery is charged at ambient temperature (21~25) ℃, with a constant current CC/CV at 0.2℃ to charge to 4.2V,and constant voltage charging to final current to 0.02C,then the battery is discharged with CC 0.2C to final voltage 2.75V, The discharge time is more than 5 hours. 3. Test： 3.1 Conditions: 3.1.1. The testing battery should not exceed one month from users received. 3.1.2.
PAGE 5
According to standard capacity charging the battery fully 4 Low temperature discharge 2) Put battery or battery pack into -10℃ ±2℃ low temperature freezer placed 4 hours then use 0.2ItA current discharge to cut-off voltage, discharge time no less than 3 hours. Battery appearance should not be cracked nor leaked.
PAGE 6
1) According to standard 7 8 Anti-Vibration capability capacity charging the battery fully 2) Fully charged Battery or Battery Pack then fixed on the vibration table, use a There should be no obvious crack, sine wave vibration and use logarithmic leakage, smoking or exploring on the sweep mode within 15min from 7Hz appearance of the sweep to 200Hz then return to 7Hz, vibration based on samples three vertical direction and every direction need repeated 12 times, total shake 3H 1) According to standard
PAGE 7
3.4 No-load voltage Voltage on shipment: 3.85V~3.95V 4.：Protection performance testing and requirements Project Over charge protection Over discharge protection Symbol Details Standard VDET1 Over Charge Prohibition ( 4. 25V~4.35V)*1 tVDET1 Over Charge Delay Time 200ms (MX) VREL1 Over Charge Release ( 4. 05V~4.15V)*1 VDET2 Over Discharge Prohibition (2.3V~2.5V )*1 tVDET2 Over Discharge Delay Time 60ms (MAX) VREL2 Over Discharge Release (2.9V~3.
PAGE 8
5 BOM Material Name Specification Description Quantity 1 Tail Care ABS +PC 1 2 Cell 063443AR 3.7V 1100mAh 1 3 Label 3.7V 1100mAh 1 4 PCB DB-D006-V1.
PAGE 9
6 .Mechanical 6.1. Mechanical Drawing（±0.2mm） 6.2:.
PAGE 10
7 . Protection: 7.1. Protection Principle Picture： 7.
PAGE 11
7.3. Port Diagram Pin Assignment (+) = Positive supply Pin (T)=Resistor 4.7K Ω Description B+ Connect to Positive terminal of cell B- Connect to negative terminal of cell P+ Connect to Camcorder +/Charger +。 P- Connect to Camcorder -/ Charger -。 T Resistor 4.
PAGE 12
7.4. PCB wiring diagram PCB Frontispiece Side PCB Reverse Side 7.5. PCB Board Dimension Drawing/mm 5.1mm 26.
PAGE 13
7.6 PCB BOM No. Name Function Unit Quan 1 PCB DB-D006-V1.0 PCS 1 / 2 IC DW01 SOT-23-6 PCS 1 U1 3 FET 8205 SOT-23-6 PCS 1 U2 4 Resistor 100R ±5% 0603 PCS 1 R1 5 Resistor 1KΩ ±5% 0603 PCS 1 R2 6 Resistor 4.