Manual

SAFETY:
The safety is local_cd on the left side of the
slide. By pushing the safety lever down as
far as possible so that the white dot Is
exposed, thus tndlcatlng the MaN"
position. ThIs blocks the firing pin from
the hammer and disconneds the trigger.
By pushing the safety lever fully upward
exposing the red dot indicates the MOFF"
firing position.
WARNINGI Accu-Tek Incorporates a well-
designed safety device; however never rely
completely on any safety mechanIsm. All
mechanical devIces are suhject to
breakage. wear or Incorrect maintenance
and should never be trusted.
AMMUNITION:
Use only commercially manufactured
ammunition and only of the caliber for
which yuur pistol is chambered.
WARNING I The use of non-5tandard,
reluaded ur hundloaded ammunition
voIds all walTantles. The use of such
ammunttion can cause damage to the
firearm and serious injury lu the shouter
or to others.
LOADING:
To load the magazine push down the front
of the follower with the rim of the
cartridge. UJen slide the round back
under the magazlne Bps. Repeat until
mal'!;azlne is loaded With up to 5 rounds.
Note: The .25 caliber is up to 7 rounds.
To unload the magazIne. push each
cartrfdge forward until it ts no longer held
by the magazine lips.
Load your firearm by keeping your finger
oIT the trigger and the safety "ON"! Insert
the magazine In the pistol by pushing It
upward Into tile magazine weH until It Is
retained by the magazIne catch.
Grip the pistol with your shoottng hand.
keeping the muzzle pointed In a safe
direction. With your other hand, grasp the
seITated surfaces at the rear of the sltde
and pull fully to the rear then release It.
promptly allowing it to return on its own.
This action will chamber the ftrst
cartridge, cock the hammer and the pistol
Is ready for firing. (If the sltde is too
dlfficult to pull bar:k. cock the hammer
first. This will enable the slide to be pulled
back with less spring pressure.)
UNLOADING:
Slide the safety lever to the ~OW (white
dol) posUlon and remove lhe magazine by
pushing the magaztne catch button on the
top of the left side grip. Keeping the pistol
pointing In a safe direction. pull tile slide
back to eject the cartridge from the
chamber. Holding the slide back. look In
tile chamber to ensure the pistol Is empty.
To de~eock yuur plstul. lite h,unmer must
be grasped and then lowered carefully as
the trigger Is pulled.
DISASSEMBLY:
WARNING! Always check to make sure
your pistol Is unloaded before you begtn to
disassemble.
Remove the trigger guard screw, then
remove the trigger guard. fully retract the
slide, 11ft up and mov(~ forward off the
frame. Do not aHow the hammer to drop
forward when the slide Is removed. as tllis
may cause damage to Lnternal p3rts. We
suggest thul YOli do not take down this
firearm any further than is explained In
tills manua1.
REASSEMBLY:
WARNING! Accu-Tek assumes no liability
or responsibility whatsoever for tnjury.
dcatil. or damage to property resulting
from IncoITect reassembly. removal or
allcrtng of uny purls In uny manner.
With the hammer cocked, replace the
slide on the baITI.:1. pull It back fully and
push It down on the frame and into the
gulrle rails. then allow the slIde to move
forward tnto position. Now replacc the
trigger guard and secure With trigger
guard screw making certain SCTCWI::;fully
seated before firing.
CARE AND CLEANING:
After dIsassembling. the barrel and
chamber should be cleaned with a bore
solvent. uslng a brush if needed. Wipe elry
and all lightly. Use a solvent on cotton
swabs or a patch 10 clean all exposed
lntcrnal surfaces.
Lubricate all movtng parts With a lIght
high quality gun aU. Be sure to lubricate
1111.:conlHcl points bdwcen the slide and
frame. and a few drops on the hammer
stll)! spring. Wipe 01Tany excess 011.
WARNING! Avoid use of solvents on grips
or prolonged use on black fintshed pistols
as 11may cause damage.