Powered by Accton ES3628C 24 10/100 Ports + 4GE Intelligent Layer 2/3/4 Fast Ethernet Switch Management Guide www.edge-core.
Management Guide Fast Ethernet Switch Layer 3 Standalone Switch with 24 100BASE-TX (RJ-45) Ports, 2 1000BASE-T (RJ-45) Ports, and 2 SFP Slots
ES3628C F3.1.0.
Contents Chapter 1: Introduction Key Features Description of Software Features System Defaults 1-1 1-1 1-2 1-7 Chapter 2: Initial Configuration Connecting to the Switch Configuration Options Required Connections Remote Connections Basic Configuration Console Connection Setting Passwords Setting an IP Address Manual Configuration Dynamic Configuration Enabling SNMP Management Access Community Strings (for SNMP version 1 and 2c clients) Trap Receivers Configuring Access for SNMP Version 3 Clients Saving Con
Contents Saving or Restoring Configuration Settings Downloading Configuration Settings from a Server Console Port Settings Telnet Settings Configuring Event Logging System Log Configuration Remote Log Configuration Displaying Log Messages Sending Simple Mail Transfer Protocol Alerts Resetting the System Setting the System Clock Configuring SNTP Setting the Time Zone Simple Network Management Protocol Enabling the SNMP Agent Setting Community Access Strings Specifying Trap Managers and Trap Types Configuring
Contents Configuring ACL Masks Specifying the Mask Type Configuring an IP ACL Mask Configuring a MAC ACL Mask Binding a Port to an Access Control List Port Configuration Displaying Connection Status Configuring Interface Connections Creating Trunk Groups Statically Configuring a Trunk Enabling LACP on Selected Ports Configuring LACP Parameters Displaying LACP Port Counters Displaying LACP Settings and Status for the Local Side Displaying LACP Settings and Status for the Remote Side Setting Broadcast Storm T
Contents Mapping Protocols to VLANs Class of Service Configuration Layer 2 Queue Settings Setting the Default Priority for Interfaces Mapping CoS Values to Egress Queues Selecting the Queue Mode Setting the Service Weight for Traffic Classes Layer 3/4 Priority Settings Mapping Layer 3/4 Priorities to CoS Values Selecting IP Precedence/DSCP Priority Mapping IP Precedence Mapping DSCP Priority Mapping IP Port Priority Quality of Service Configuring Quality of Service Parameters Configuring a Class Map Creatin
Contents IP Routing Overview Initial Configuration IP Switching Routing Path Management Routing Protocols Basic IP Interface Configuration Configuring IP Routing Interfaces Address Resolution Protocol Proxy ARP Basic ARP Configuration Configuring Static ARP Addresses Displaying Dynamically Learned ARP Entries Displaying Local ARP Entries Displaying ARP Statistics Displaying Statistics for IP Protocols IP Statistics ICMP Statistics UDP Statistics TCP Statistics Configuring Static Routes Displaying the Routin
Contents Configuring DVMRP Interface Settings Displaying Neighbor Information Displaying the Routing Table Configuring PIM-DM Configuring Global PIM-DM Settings Configuring PIM-DM Interface Settings Displaying Interface Information Displaying Neighbor Information Chapter 4: Command Line Interface Using the Command Line Interface Accessing the CLI Console Connection Telnet Connection Entering Commands Keywords and Arguments Minimum Abbreviation Command Completion Getting Help on Commands Showing Commands Par
Contents disable configure show history reload end exit quit System Management Commands Device Designation Commands prompt hostname User Access Commands username enable password IP Filter Commands management show management Web Server Commands ip http port ip http server ip http secure-server ip http secure-port Telnet Server Commands ip telnet server Secure Shell Commands ip ssh server ip ssh timeout ip ssh authentication-retries ip ssh server-key size delete public-key ip ssh crypto host-key generate ip s
Contents SMTP Alert Commands logging sendmail host logging sendmail level logging sendmail source-email logging sendmail destination-email logging sendmail show logging sendmail Time Commands sntp client sntp server sntp poll show sntp clock timezone calendar set show calendar System Status Commands show startup-config show running-config show system show users show version Frame Size Commands jumbo frame Flash/File Commands copy delete dir whichboot boot system Authentication Commands Authentication Sequen
Contents Port Security Commands port security 802.
Contents snmp-server engine-id show snmp engine-id snmp-server view show snmp view snmp-server group show snmp group snmp-server user show snmp user DHCP Commands DHCP Client ip dhcp client-identifier ip dhcp restart client DHCP Relay ip dhcp restart relay ip dhcp relay server DHCP Server service dhcp ip dhcp excluded-address ip dhcp pool network default-router domain-name dns-server next-server bootfile netbios-name-server netbios-node-type lease host client-identifier hardware-address clear ip dhcp bindin
Contents Interface Commands interface description speed-duplex negotiation capabilities shutdown switchport broadcast packet-rate clear counters show interfaces status show interfaces counters show interfaces switchport Mirror Port Commands port monitor show port monitor Rate Limit Commands rate-limit Link Aggregation Commands channel-group lacp lacp system-priority lacp admin-key (Ethernet Interface) lacp admin-key (Port Channel) lacp port-priority show lacp Address Table Commands mac-address-table static
Contents max-hops spanning-tree spanning-disabled spanning-tree cost spanning-tree port-priority spanning-tree edge-port spanning-tree portfast spanning-tree link-type spanning-tree mst cost spanning-tree mst port-priority spanning-tree protocol-migration show spanning-tree show spanning-tree mst configuration VLAN Commands Editing VLAN Groups vlan database vlan Configuring VLAN Interfaces interface vlan switchport mode switchport acceptable-frame-types switchport ingress-filtering switchport native vlan sw
Contents queue bandwidth queue cos-map show queue mode show queue bandwidth show queue cos-map Priority Commands (Layer 3 and 4) map ip port (Global Configuration) map ip port (Interface Configuration) map ip precedence (Global Configuration) map ip precedence (Interface Configuration) map ip dscp (Global Configuration) map ip dscp (Interface Configuration) show map ip port show map ip precedence show map ip dscp Quality of Service Commands class-map match policy-map class set police service-policy show cla
Contents ip igmp query-interval ip igmp max-resp-interval ip igmp last-memb-query-interval ip igmp version show ip igmp interface clear ip igmp group show ip igmp groups IP Interface Commands Basic IP Configuration ip address ip default-gateway show ip interface show ip redirects ping Address Resolution Protocol (ARP) arp arp-timeout clear arp-cache show arp ip proxy-arp IP Routing Commands Global Routing Configuration ip routing ip route clear ip route show ip route show ip host-route show ip traffic Routi
Contents default-information originate timers spf area range area default-cost summary-address redistribute network area area stub area nssa area virtual-link ip ospf authentication ip ospf authentication-key ip ospf message-digest-key ip ospf cost ip ospf dead-interval ip ospf hello-interval ip ospf priority ip ospf retransmit-interval ip ospf transmit-delay show ip ospf show ip ospf border-routers show ip ospf database show ip ospf interface show ip ospf neighbor show ip ospf summary-address show ip ospf
Contents show ip dvmrp route show ip dvmrp neighbor show ip dvmrp interface PIM-DM Multicast Routing Commands router pim ip pim dense-mode ip pim hello-interval ip pim hello-holdtime ip pim trigger-hello-interval ip pim join-prune-holdtime ip pim graft-retry-interval ip pim max-graft-retries show router pim show ip pim interface show ip pim neighbor Router Redundancy Commands Virtual Router Redundancy Protocol Commands vrrp ip vrrp authentication vrrp priority vrrp timers advertise vrrp preempt show vrrp sh
Tables Table 1-1 Table 1-2 Table 3-1 Table 3-2 Table 3-3 Table 3-4 Table 3-5 Table 3-6 Table 3-7 Table 3-8 Table 3-9 Table 3-10 Table 3-11 Table 3-12 Table 3-13 Table 3-14 Table 3-15 Table 3-16 Table 3-17 Table 3-18 Table 3-19 Table 3-20 Table 3-21 Table 3-22 Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 4-6 Table 4-7 Table 4-8 Table 4-9 Table 4-10 Table 4-11 Table 4-12 Table 4-13 Table 4-14 Table 4-15 Table 4-16 Table 4-17 xxi Key Features System Defaults Web Page Configuration Buttons Switch Ma
Tables Table 4-18 Table 4-19 Table 4-20 Table 4-21 Table 4-22 Table 4-23 Table 4-24 Table 4-25 Table 4-26 Table 4-27 Table 4-28 Table 4-29 Table 4-30 Table 4-31 Table 4-32 Table 4-33 Table 4-34 Table 4-35 Table 4-36 Table 4-37 Table 4-38 Table 4-39 Table 4-40 Table 4-41 Table 4-42 Table 4-43 Table 4-44 Table 4-45 Table 4-46 Table 4-47 Table 4-48 Table 4-49 Table 4-50 Table 4-51 Table 4-52 Table 4-53 Table 4-54 Table 4-55 Table 4-57 Table 4-56 Table 4-58 Table 4-59 Table 4-60 Table 4-61 Table 4-62 xxii Logg
Tables Table 4-63 Table 4-64 Table 4-65 Table 4-66 Table 4-67 Table 4-68 Table 4-69 Table 4-70 Table 4-71 Table 4-72 Table 4-73 Table 4-74 Table 4-75 Table 4-76 Table 4-77 Table 4-78 Table 4-79 Table 4-80 Table 4-81 Table 4-82 Table 4-83 Table 4-84 Table 4-85 Table 4-86 Table 4-87 Table 4-88 Table 4-89 Table 4-91 Table 4-90 Table 4-92 Table 4-93 Table 4-94 Table 4-95 Table 4-96 Table 4-97 Table 4-98 Table 4-99 Table 4-100 Table 4-101 Table 4-102 Table 4-103 Table 4-104 Table 4-105 Table 4-106 Table 4-107 P
Tables Table 4-108 Table 4-109 Table 4-110 Table 4-111 Table 4-112 Table 4-113 Table 4-114 Table B-1 xxiv show ip dvmrp neighbor - display description PIM-DM Multicast Routing Commands show ip pim neighbor - display description Router Redundancy Commands VRRP Commands show vrrp - display description show vrrp brief - display description Troubleshooting Chart 4-309 4-310 4-316 4-316 4-317 4-322 4-323 B-1
Figures Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12 Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16 Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 3-21 Figure 3-22 Figure 3-23 Figure 3-24 Figure 3-25 Figure 3-26 Figure 3-27 Figure 3-28 Figure 3-29 Figure 3-30 Figure 3-31 Figure 3-32 Figure 3-33 Figure 3-34 Figure 3-35 Figure 3-36 Figure 3-37 Figure 3-38 Figure 3-39 Figure 3-40 Figure 3-41 Home Page Front Pane
Figures Figure 3-42 Figure 3-43 Figure 3-44 Figure 3-45 Figure 3-46 Figure 3-47 Figure 3-48 Figure 3-49 Figure 3-50 Figure 3-51 Figure 3-52 Figure 3-53 Figure 3-54 Figure 3-55 Figure 3-56 Figure 3-57 Figure 3-58 Figure 3-59 Figure 3-60 Figure 3-61 Figure 3-62 Figure 3-63 Figure 3-64 Figure 3-65 Figure 3-66 Figure 3-67 Figure 3-68 Figure 3-69 Figure 3-70 Figure 3-71 Figure 3-72 Figure 3-73 Figure 3-74 Figure 3-75 Figure 3-76 Figure 3-77 Figure 3-78 Figure 3-79 Figure 3-80 Figure 3-81 Figure 3-82 Figure 3-83
Figures Figure 3-87 Figure 3-88 Figure 3-89 Figure 3-90 Figure 3-91 Figure 3-92 Figure 3-93 Figure 3-94 Figure 3-95 Figure 3-96 Figure 3-97 Figure 3-98 Figure 3-99 Figure 3-100 Figure 3-101 Figure 3-102 Figure 3-103 Figure 3-104 Figure 3-105 Figure 3-106 Figure 3-107 Figure 3-108 Figure 3-109 Figure 3-110 Figure 3-111 Figure 3-112 Figure 3-113 Figure 3-114 Figure 3-115 Figure 3-116 Figure 3-117 Figure 3-118 Figure 3-119 Figure 3-120 Figure 3-121 Figure 3-122 Figure 3-123 Figure 3-124 Figure 3-125 Figure 3-1
Figures Figure 3-132 Figure 3-133 Figure 3-134 Figure 3-135 Figure 3-136 Figure 3-137 Figure 3-138 Figure 3-139 Figure 3-140 Figure 3-141 Figure 3-142 Figure 3-143 Figure 3-144 Figure 3-145 Figure 3-146 Figure 3-147 Figure 3-148 Figure 3-149 Figure 3-150 Figure 3-151 Figure 3-152 Figure 3-153 Figure 3-154 Figure 3-155 Figure 3-156 xxviii RIP Interface Settings RIP Statistics OSPF General Configuration OSPF Area Configuration OSPF Range Configuration OSPF Interface Configuration OSPF Interface Configuratio
Chapter 1: Introduction This switch provides a broad range of features for Layer 2 switching and Layer 3 routing. It includes a management agent that allows you to configure the features listed in this manual. The default configuration can be used for most of the features provided by this switch. However, there are many options that you should configure to maximize the switch’s performance for your particular network environment.
1 Introduction Table 1-1 Key Features (Continued) Feature Description Traffic Prioritization Default port priority, traffic class map, queue scheduling, IP Precedence, or Differentiated Services Code Point (DSCP), and TCP/UDP Port Qualify of Service Supports Differentiated Services (DiffServ) Router Redundancy Router backup is provided with the Virtual Router Redundancy Protocol (VRRP) IP Routing Routing Information Protocol (RIP), Open Shortest Path First (OSPF), static routes ARP Static and d
Description of Software Features 1 Access Control Lists – ACLs provide packet filtering for IP frames (based on address, protocol, TCP/UDP port number or TCP control code) or any frames (based on MAC address or Ethernet type). ACLs can by used to improve performance by blocking unnecessary network traffic or to implement security controls by restricting access to specific network resources or protocols. DHCP Server and DHCP Relay – A DHCP server is provided to assign IP addresses to host devices.
1 Introduction IEEE 802.1D Bridge – The switch supports IEEE 802.1D transparent bridging. The address table facilitates data switching by learning addresses, and then filtering or forwarding traffic based on this information. The address table supports up to 16K addresses. Store-and-Forward Switching – The switch copies each frame into its memory before forwarding them to another port.
Description of Software Features 1 • Use private VLANs to restrict traffic to pass only between data ports and the uplink ports, thereby isolating adjacent ports within the same VLAN, and allowing you to limit the total number of VLANs that need to be configured. • Use protocol VLANs to restrict traffic to specified interfaces based on protocol type.
1 Introduction remote network, the switch checks to see if it has the best route. If it does, it sends its own MAC address to the host. The host then sends traffic for the remote destination via the switch, which uses its own routing table to reach the destination on the other network. Quality of Service – Differentiated Services (DiffServ) provides policy-based management mechanisms used for prioritizing network resources to meet the requirements of specific traffic types on a per-hop basis.
System Defaults 1 System Defaults The switch’s system defaults are provided in the configuration file “Factory_Default_Config.cfg.” To reset the switch defaults, this file should be set as the startup configuration file (page 3-24). The following table lists some of the basic system defaults.
1 Introduction Table 1-2 System Defaults (Continued) Function Parameter Default SNMP SNMP Agent Enabled Community Strings “public” (read only) “private” (read/write) Traps Authentication traps: enabled Link-up-down events: enabled SNMP V3 View: defaultview Group: public (read only); private (read/write) Admin Status Enabled Auto-negotiation Enabled Port Configuration Flow Control Disabled Rate Limiting Input and output limits Disabled Port Trunking Static Trunks None LACP (all por
System Defaults 1 Table 1-2 System Defaults (Continued) Function Parameter Default IP Settings Management. VLAN Any VLAN configured with an IP address IP Address 0.0.0.0 Unicast Routing Subnet Mask 255.0.0.0 Default Gateway 0.0.0.
1 1-10 Introduction
Chapter 2: Initial Configuration Connecting to the Switch Configuration Options The switch includes a built-in network management agent. The agent offers a variety of management options, including SNMP, RMON and a web-based interface. A PC may also be connected directly to the switch for configuration and monitoring via a command line interface (CLI). Note: The IP address for this switch is obtained via DHCP by default. To change this address, see “Setting an IP Address” on page 2-4.
2 • • • • • • Initial Configuration Configure Spanning Tree parameters Configure Class of Service (CoS) priority queuing Configure up to 12 static or LACP trunks Enable port mirroring Set broadcast storm control on any port Display system information and statistics Required Connections The switch provides an RS-232 serial port that enables a connection to a PC or terminal for monitoring and configuring the switch. A null-modem console cable is provided with the switch.
Basic Configuration 2 Remote Connections Prior to accessing the switch’s onboard agent via a network connection, you must first configure it with a valid IP address, subnet mask, and default gateway using a console connection, DHCP or BOOTP protocol. The IP address for this switch is obtained via DHCP by default. To manually configure this address or enable dynamic address assignment via DHCP or BOOTP, see “Setting an IP Address” on page 2-4. Notes: 1.
2 Initial Configuration Setting Passwords Note: If this is your first time to log into the CLI program, you should define new passwords for both default user names using the “username” command, record them and put them in a safe place. Passwords can consist of up to 8 alphanumeric characters and are case sensitive. To prevent unauthorized access to the switch, set the passwords as follows: 1. Open the console interface with the default user name and password “admin” to access the Privileged Exec level.
Basic Configuration 2 Before you can assign an IP address to the switch, you must obtain the following information from your network administrator: • IP address for the switch • Default gateway for the network • Network mask for this network To assign an IP address to the switch, complete the following steps: 1. From the Privileged Exec level global configuration mode prompt, type “interface vlan 1” to access the interface-configuration mode. Press . 2.
2 Initial Configuration 5. Wait a few minutes, and then check the IP configuration settings by typing the “show ip interface” command. Press . 6. Then save your configuration changes by typing “copy running-config startup-config.” Enter the startup file name and press . Console(config)#interface vlan 1 Console(config-if)#ip address dhcp Console(config-if)#end Console#ip dhcp restart client Console#show ip interface IP address and netmask: 192.168.1.54 255.255.255.
Basic Configuration 2 The default strings are: • public - with read-only access. Authorized management stations are only able to retrieve MIB objects. • private - with read-write access. Authorized management stations are able to both retrieve and modify MIB objects. To prevent unauthorized access to the switch from SNMP version 1 or 2c clients, it is recommended that you change the default community strings. To configure a community string, complete the following steps: 1.
2 Initial Configuration Configuring Access for SNMP Version 3 Clients To configure management access for SNMPv3 clients, you need to first create a view that defines the portions of MIB that the client can read or write, assign the view to a group, and then assign the user to a group. The following example creates one view called “mib-2” that includes the entire MIB-2 tree branch, and then another view that includes the IEEE 802.1d bridge MIB.
Managing System Files 2 Managing System Files The switch’s flash memory supports three types of system files that can be managed by the CLI program, web interface, or SNMP. The switch’s file system allows files to be uploaded and downloaded, copied, deleted, and set as a start-up file. The three types of files are: • Configuration — This file type stores system configuration information and is created when configuration settings are saved.
2 2-10 Initial Configuration
Chapter 3: Configuring the Switch Using the Web Interface This switch provides an embedded HTTP web agent. Using a web browser you can configure the switch and view statistics to monitor network activity. The web agent can be accessed by any computer on the network using a standard web browser (Internet Explorer 5.0 or above, or Netscape Navigator 6.2 or above). Note: You can also use the Command Line Interface (CLI) to manage the switch over a serial connection to the console port or via Telnet.
3 Configuring the Switch Navigating the Web Browser Interface To access the web-browser interface you must first enter a user name and password. The administrator has Read/Write access to all configuration parameters and statistics. The default user name and password “admin” is used for the administrator. Home Page When your web browser connects with the switch’s web agent, the home page is displayed as shown below.
Navigating the Web Browser Interface 3 Configuration Options Configurable parameters have a dialog box or a drop-down list. Once a configuration change has been made on a page, be sure to click on the Apply button to confirm the new setting. The following table summarizes the web page configuration buttons. Table 3-1 Web Page Configuration Buttons Button Action Apply Sets specified values to the system. Revert Cancels specified values and restores current values prior to pressing “Apply.
3 Configuring the Switch Main Menu Using the onboard web agent, you can define system parameters, manage and control the switch, and all its ports, or monitor network conditions. The following table briefly describes the selections available from this program.
Navigating the Web Browser Interface 3 Table 3-2 Switch Main Menu (Continued) Menu Description SNMPv3 Engine ID Page 3-42 Sets the SNMP v3 engine ID 3-43 Remote Engine ID Sets the SNMP v3 engine ID on a remote device 3-43 Users Configures SNMP v3 users 3-44 Remote Users Configures SNMP v3 users on a remote device 3-46 Groups Configures SNMP v3 groups 3-48 Views Configures SNMP v3 views 3-52 User Accounts Configures user names, passwords, and access levels 3-53 Authentication Settin
3 Configuring the Switch Table 3-2 Switch Main Menu (Continued) Menu Description LACP Configuration Page 3-93 Allows ports to dynamically join trunks 3-95 Aggregation Port Configures parameters for link aggregation group members Port Counters Information Displays statistics for LACP protocol messages 3-101 Port Internal Information Displays settings and operational state for the local side 3-102 Port Neighbors Information Displays settings and operational state for the remote side 3-98 3-1
Navigating the Web Browser Interface 3 Table 3-2 Switch Main Menu (Continued) Menu Trunk Configuration Description Configures trunk settings for a specified MST instance VLAN Page 3-133 3-135 802.
3 Configuring the Switch Table 3-2 Switch Main Menu (Continued) Menu Description QoS Page 3-161 DiffServ Configure QoS classification criteria and service policies 3-161 Class Map Creates a class map for a type of traffic 3-162 Policy Map Creates a policy map for multiple interfaces 3-165 Service Policy Applies a policy map defined to an ingress port 3-168 IGMP Snooping 3-169 IGMP Configuration Enables multicast filtering; configures parameters for multicast query 3-171 Multicast Rout
Navigating the Web Browser Interface 3 Table 3-2 Switch Main Menu (Continued) Menu Description ARP General Page 3-211 Sets the protocol timeout, and enables or disables proxy ARP for the specified VLAN 3-212 Static Addresses Statically maps a physical address to an IP address 3-213 Dynamic Addresses Shows dynamically learned entries in the IP routing table 3-214 Other Addresses Shows internal addresses used by the switch 3-215 Statistics Shows statistics on ARP requests sent and received
3 Configuring the Switch Table 3-2 Switch Main Menu (Continued) Menu Description Routing Protocol 3-207 RIP 3-225 General Settings Enables or disables RIP, sets the global RIP version and timer values 3-226 Network Addresses Configures the network interfaces that will use RIP 3-228 Interface Settings Configures RIP parameters for each interface, including send and receive versions, message loopback prevention, and authentication 3-229 Statistics Displays general information on update time,
Navigating the Web Browser Interface 3 Table 3-2 Switch Main Menu (Continued) Menu Description Page PIM-DM General Settings Enables or disables PIM-DM globally for the switch 3-272 Interface Settings Enables or disables PIM-DM per interface, configures protocol settings for hello, prune and graft messages 3-273 Interface Information Displays summary information for each interface 3-276 Neighbor Information Displays neighboring PIM-DM routers 3-276 3-11
3 Configuring the Switch Basic Configuration Displaying System Information You can easily identify the system by displaying the device name, location and contact information. Field Attributes • System Name – Name assigned to the switch system. • Object ID – MIB II object ID for switch’s network management subsystem. • Location – Specifies the system location. • Contact – Administrator responsible for the system. • System Up Time – Length of time the management agent has been up.
Basic Configuration 3 CLI – Specify the hostname, location and contact information. Console(config)#hostname R&D 5 4-26 Console(config)#snmp-server location WC 9 4-110 Console(config)#snmp-server contact Ted 4-109 Console(config)#exit Console#show system 4-60 System description: 24/48 L3 GE Switch System OID String: 1.3.6.1.4.1.259.6.10.75 System information System Up Time: 0 days, 7 hours, 0 minutes, and 33.
3 Configuring the Switch • Operation Code Version – Version number of runtime code. • Role – Shows that this switch is operating as Master or Slave2. These additional parameters are displayed for the CLI. • Unit ID – Unit number in stack2. • Redundant Power Status – Displays the status of the redundant power supply. Web – Click System, Switch Information. Figure 3-4 Switch Information CLI – Use the following command to display version information.
Basic Configuration 3 Displaying Bridge Extension Capabilities The Bridge MIB includes extensions for managed devices that support Multicast Filtering, Traffic Classes, and Virtual LANs. You can access these extensions to display default settings for the key variables. Field Attributes • Extended Multicast Filtering Services – This switch does not support the filtering of individual multicast addresses based on GMRP (GARP Multicast Registration Protocol).
3 Configuring the Switch CLI – Enter the following command.
Basic Configuration 3 Setting the Switch’s IP Address This section describes how to configure an initial IP interface for management access over the network. The IP address for this switch is obtained via DHCP by default. To manually configure an address, you need to change the switch’s default settings to values that are compatible with your network.
3 Configuring the Switch Manual Configuration Web – Click IP, General, Routing Interface. Select the VLAN through which the management station is attached, set the IP Address Mode to “Static,” and specify a “Primary” interface. Enter the IP address, subnet mask and gateway, then click Apply. Figure 3-7 IP Interface Configuration - Manual Click IP, Global Setting. If this switch and management stations exist on other network segments, then specify the default gateway, and click Apply.
3 Basic Configuration Using DHCP/BOOTP If your network provides DHCP/BOOTP services, you can configure the switch to be dynamically configured by these services. Web – Click IP, General, Routing Interface. Specify the VLAN to which the management station is attached, set the IP Address Mode to DHCP or BOOTP. Click Apply to save your changes. Then click Restart DHCP to immediately request a new address. Note that the switch will also broadcast a request for IP configuration settings on each power reset.
3 Configuring the Switch Renewing DCHP – DHCP may lease addresses to clients indefinitely or for a specific period of time. If the address expires or the switch is moved to another network segment, you will lose management access to the switch. In this case, you can reboot the switch or submit a client request to restart DHCP service via the CLI. Web – If the address assigned by DHCP is no longer functioning, you will not be able to renew the IP settings via the web interface.
Basic Configuration 3 Downloading System Software from a Server When downloading runtime code, you can specify the destination file name to replace the current image, or first download the file using a different name from the current runtime code file, and then set the new file as the startup file. Web – Click System, File Management, Copy Operation.
3 Configuring the Switch To delete a file select System, File Management, Delete. Select the file name from the given list by checking the tick box and click Apply. Note that the file currently designated as the startup code cannot be deleted. Figure 3-12 Deleting Files CLI – To download new firmware form a TFTP server, enter the IP address of the TFTP server, select “config” as the file type, then enter the source and destination file names.
Basic Configuration 3 Saving or Restoring Configuration Settings You can upload/download configuration settings to/from a TFTP server, or copy files to and from switch units in a stack4. The configuration file can be later downloaded to restore the switch’s settings. Command Attributes • File Transfer Method – The configuration copy operation includes these options: - file to file – Copies a file within the switch directory, assigning it a new name.
3 Configuring the Switch Downloading Configuration Settings from a Server You can download the configuration file under a new file name and then set it as the startup file, or you can specify the current startup configuration file as the destination file to directly replace it. Note that the file “Factory_Default_Config.cfg” can be copied to the TFTP server, but cannot be used as the destination on the switch. Web – Click System, File Management, Copy Operation.
Basic Configuration 3 CLI – Enter the IP address of the TFTP server, specify the source file on the server, set the startup file name on the switch, and then restart the switch. Console#copy tftp startup-config TFTP server ip address: 192.168.1.19 Source configuration file name: config-1 Startup configuration file name [] : startup \Write to FLASH Programming. -Write to FLASH finish. Success.
3 Configuring the Switch • Speed – Sets the terminal line’s baud rate for transmit (to terminal) and receive (from terminal). Set the speed to match the baud rate of the device connected to the serial port. (Range: 9600, 19200, 38400, 57600, or 115200 baud, Auto; Default: Auto) • Stop Bits – Sets the number of the stop bits transmitted per byte. (Range: 1-2; Default: 1 stop bit) • Password5 – Specifies a password for the line connection.
Basic Configuration 3 CLI – Enter Line Configuration mode for the console, then specify the connection parameters as required. To display the current console port settings, use the show line command from the Normal Exec level.
3 Configuring the Switch • Password6 – Specifies a password for the line connection. When a connection is started on a line with password protection, the system prompts for the password. If you enter the correct password, the system shows a prompt. (Default: No password) • Login6 – Enables password checking at login. You can select authentication by a single global password as configured for the Password parameter, or by passwords set up for specific user-name accounts.
Basic Configuration 3 Configuring Event Logging The switch allows you to control the logging of error messages, including the type of events that are recorded in switch memory, logging to a remote System Log (syslog) server, and displays a list of recent event messages. System Log Configuration The system allows you to enable or disable event logging, and specify which levels are logged to RAM or flash memory.
3 Configuring the Switch Web – Click System, Logs, System Logs. Specify System Log Status, set the level of event messages to be logged to RAM and flash memory, then click Apply. Figure 3-17 System Logs CLI – Enable system logging and then specify the level of messages to be logged to RAM and flash memory. Use the show logging command to display the current settings.
Basic Configuration 3 Web – Click System, Logs, Remote Logs. To add an IP address to the Host IP List, type the new IP address in the Host IP Address box, and then click Add. To delete an IP address, click the entry in the Host IP List, and then click Remove. Figure 3-18 Remote Logs CLI – Enter the syslog server host IP address, choose the facility type and set the logging trap. Console(config)#logging host 10.1.0.
3 Configuring the Switch Displaying Log Messages Use the Logs page to scroll through the logged system and event messages. The switch can store up to 2048 log entries in temporary random access memory (RAM; i.e., memory flushed on power reset) and up to 4096 entries in permanent flash memory. Web – Click System, Log, Logs. Figure 3-19 Displaying Logs CLI – This example shows the event message stored in RAM. Console#show log ram [1] 00:01:30 2001-01-01 "VLAN 1 link-up notification.
Basic Configuration 3 • SMTP Server List – Specifies a list of up to three recipient SMTP servers. The switch attempts to connect to the other listed servers if the first fails. Use the New SMTP Server text field and the Add/Remove buttons to configure the list. • Email Destination Address List – Specifies the email recipients of alert messages. You can specify up to five recipients. Use the New Email Destination Address text field and the Add/Remove buttons to configure the list.
3 Configuring the Switch CLI – Enter the IP address of at least one SMTP server, set the syslog severity level to trigger an email message, and specify the switch (source) and up to five recipient (destination) email addresses. Enable SMTP with the logging sendmail command to complete the configuration. Use the show logging sendmail command to display the current SMTP configuration. Console(config)#logging sendmail host 192.168.1.
Basic Configuration 3 Setting the System Clock Simple Network Time Protocol (SNTP) allows the switch to set its internal clock based on periodic updates from a time server (SNTP or NTP). Maintaining an accurate time on the switch enables the system log to record meaningful dates and times for event entries. You can also manually set the clock using the CLI. (See “calendar set” on page 4-56.) If the clock is not set, the switch will only record the time from the factory default set at the last bootup.
3 Configuring the Switch CLI – This example configures the switch to operate as an SNTP client and then displays the current time and settings. Console(config)#sntp client Console(config)#sntp poll 16 Console(config)#sntp server 10.1.0.19 137.82.140.80 128.250.36.2 Console(config)#exit Console#show sntp Current time: Jan 6 14:56:05 2004 Poll interval: 60 Current mode: unicast SNTP status : Enabled SNTP server 10.1.0.19 137.82.140.80 128.250.36.2 Current server: 128.250.36.
Simple Network Management Protocol 3 Simple Network Management Protocol Simple Network Management Protocol (SNMP) is a communication protocol designed specifically for managing devices on a network. Equipment commonly managed with SNMP includes switches, routers and host computers. SNMP is typically used to configure these devices for proper operation in a network environment, as well as to monitor them to evaluate performance or detect potential problems.
3 Configuring the Switch security models v1 and v2c. The following table shows the security models and levels available and the system default settings.
Simple Network Management Protocol 3 CLI – The following example enables SNMP on the switch. Console(config)#snmp-server Console(config)# 4-107 Setting Community Access Strings You may configure up to five community strings authorized for management access by clients using SNMP v1 and v2c. All community strings used for IP Trap Managers should be listed in this table. For security reasons, you should consider removing the default strings.
3 Configuring the Switch Specifying Trap Managers and Trap Types Traps indicating status changes are issued by the switch to specified trap managers. You must specify trap managers so that key events are reported by this switch to your management station (using network management platforms such as HP OpenView). You can specify up to five management stations that will receive authentication failure messages and other trap messages from the switch.
Simple Network Management Protocol 3 Version 1 or 2c clients), or define a corresponding “User Name” in the SNMPv3 Users page (for Version 3 clients). (Range: 1-32 characters, case sensitive) • Trap UDP Port – Specifies the UDP port number used by the trap manager. • Trap Version – Indicates if the user is running SNMP v1, v2c, or v3. (Default: v1) • Trap Security Level – When trap version 3 is selected, you must specify one of the following security levels.
3 Configuring the Switch Web – Click SNMP, Configuration. Enter the IP address and community string for each management station that will receive trap messages, specify the UDP port, SNMP trap version, trap security level (for v3 clients), trap inform settings (for v2c/v3 clients), and then click Add. Select the trap types required using the check boxes for Authentication and Link-up/down traps, and then click Apply.
3 Simple Network Management Protocol Setting a Local Engine ID An SNMPv3 engine is an independent SNMP agent that resides on the switch. This engine protects against message replay, delay, and redirection. The engine ID is also used in combination with user passwords to generate the security keys for authenticating and encrypting SNMPv3 packets. A local engine ID is automatically generated that is unique to the switch. This is referred to as the default engine ID.
3 Configuring the Switch The engine ID can be specified by entering 1 to 26 hexadecimal characters. If less than 26 characters are specified, trailing zeroes are added to the value. For example, the value “1234” is equivalent to “1234” followed by 22 zeroes. Web – Click SNMP, SNMPv3, Remote Engine ID. Enter an ID of up to 26 hexadecimal characters and then click Save. Figure 3-28 Setting an Engine ID CLI – This example specifies a remote SNMPv3 engine ID.
Simple Network Management Protocol 3 • Privacy Protocol – The encryption algorithm use for data privacy; only 56-bit DES is currently available. • Privacy Password – A minimum of eight plain text characters is required. • Actions – Enables the user to be assigned to another SNMPv3 group. Web – Click SNMP, SNMPv3, Users. Click New to configure a user name. In the New User page, define a name and assign it to a group, then click Add to save the configuration and return to the User Name list.
3 Configuring the Switch CLI – Use the snmp-server user command to configure a new user name and assign it to a group. Console(config)#snmp-server user chris group r&d v3 auth md5 greenpeace priv des56 einstien Console(config)#exit Console#show snmp user EngineId: 80000034030001f488f5200000 User Name: chris Authentication Protocol: md5 Privacy Protocol: des56 Storage Type: nonvolatile Row Status: active 4-118 4-120 Console# Configuring Remote SNMPv3 Users Each SNMPv3 user is defined by a unique name.
Simple Network Management Protocol 3 • Privacy Protocol – The encryption algorithm use for data privacy; only 56-bit DES is currently available. • Privacy Password – A minimum of eight plain text characters is required. Web – Click SNMP, SNMPv3, Remote Users. Click New to configure a user name. In the New User page, define a name and assign it to a group, then click Add to save the configuration and return to the User Name list. To delete a user, check the box next to the user name, then click Delete.
3 Configuring the Switch CLI – Use the snmp-server user command to configure a new user name and assign it to a group. Console(config)#snmp-server user mark group r&d remote 192.168.1.19 v3 auth md5 greenpeace priv des56 einstien 4-118 Console(config)#exit Console#show snmp user 4-120 No user exist.
Simple Network Management Protocol 3 Table 3-5 Supported Notification Messages Object Label Object ID Description newRoot 1.3.6.1.2.1.17.0.1 The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election. topologyChange 1.3.6.1.2.1.17.0.
3 Configuring the Switch Table 3-5 Supported Notification Messages (Continued) Object Label Object ID Description swPowerStatus ChangeTrap 1.3.6.1.4.1.259.6.10.75.2.1.0.1 This trap is sent when the power state changes. swFanFailureTrap 1.3.6.1.4.1.259.6.10.75.2.1.0.17 This trap is sent when the fan fails. swFanRecoverTrap 1.3.6.1.4.1.259.6.10.75.2.1.0.18 This trap is sent when the fan failure has recovered. swIpFilterRejectTrap 1.3.6.1.4.1.259.6.10.75.2.1.0.
Simple Network Management Protocol 3 Web – Click SNMP, SNMPv3, Groups. Click New to configure a new group. In the New Group page, define a name, assign a security model and level, and then select read, write, and notify views. Click Add to save the new group and return to the Groups list. To delete a group, check the box next to the group name, then click Delete.
3 Configuring the Switch Setting SNMPv3 Views SNMPv3 views are used to restrict user access to specified portions of the MIB tree. The predefined view “defaultview” includes access to the entire MIB tree. Command Attributes • View Name – The name of the SNMP view. (Range: 1-64 characters) • View OID Subtrees – Shows the currently configured object identifiers of branches within the MIB tree that define the SNMP view.
3 User Authentication CLI – Use the snmp-server view command to configure a new view. This example view includes the MIB-2 interfaces table, and the wildcard mask selects all index entries. Console(config)#snmp-server view ifEntry.a 1.3.6.1.2.1.2.2.1.1.* included Console(config)#exit Console#show snmp view View Name: ifEntry.a Subtree OID: 1.3.6.1.2.1.2.2.1.1.* View Type: included Storage Type: nonvolatile Row Status: active 4-115 4-116 View Name: readaccess Subtree OID: 1.3.6.1.
3 Configuring the Switch Command Attributes • Account List – Displays the current list of user accounts and associated access levels. (Defaults: admin, and guest) • New Account – Displays configuration settings for a new account. - User Name – The name of the user. (Maximum length: 8 characters; maximum number of users: 16) - Access Level – Specifies the user level. (Options: Normal and Privileged) - Password – Specifies the user password.
User Authentication 3 Configuring Local/Remote Logon Authentication Use the Authentication Settings menu to restrict management access based on specified user names and passwords. You can manually configure access rights on the switch, or you can use a remote access authentication server based on RADIUS or TACACS+ protocols.
3 Configuring the Switch • RADIUS Settings - Global – Provides globally applicable RADIUS settings. - ServerIndex – Specifies one of five RADIUS servers that may be configured. The switch attempts authentication using the listed sequence of servers. The process ends when a server either approves or denies access to a user. - Server IP Address – Address of authentication server. (Default: 10.1.0.1) - Server Port Number – Network (UDP) port of authentication server used for authentication messages.
User Authentication 3 Web – Click Security, Authentication Settings. To configure local or remote authentication preferences, specify the authentication sequence (i.e., one to three methods), fill in the parameters for RADIUS or TACACS+ authentication if selected, and click Apply. Figure 3-34 Authentication Server Settings CLI – Specify all the required parameters to enable logon authentication.
3 Configuring the Switch Console#config Console(config)#authentication login tacacs Console(config)#tacacs-server host 10.20.30.40 Console(config)#tacacs-server port 200 Console(config)#tacacs-server key green Console(config)#exit Console#show tacacs-server Server IP address: 10.20.30.
3 User Authentication Web – Click Security, HTTPS Settings. Enable HTTPS and specify the port number, then click Apply. Figure 3-35 HTTPS Settings CLI – This example enables the HTTP secure server and modifies the port number.
3 Configuring the Switch Configuring the Secure Shell The Berkley-standard includes remote access tools originally designed for Unix systems. Some of these tools have also been implemented for Microsoft Windows and other environments. These tools, including commands such as rlogin (remote login), rsh (remote shell), and rcp (remote copy), are not secure from hostile attacks.
User Authentication 3 be configured locally on the switch via the User Accounts page as described on page 3-53.) The clients are subsequently authenticated using these keys.
3 Configuring the Switch Field Attributes • Public-Key of Host-Key – The public key for the host. - RSA (Version 1): The first field indicates the size of the host key (e.g., 1024), the second field is the encoded public exponent (e.g., 65537), and the last string is the encoded modulus. - DSA (Version 2): The first field indicates that the encryption method used by SSH is based on the Digital Signature Standard (DSS). The last string is the encoded modulus.
User Authentication 3 CLI – This example generates a host-key pair using both the RSA and DSA algorithms, stores the keys to flash memory, and then displays the host’s public keys.
3 Configuring the Switch Web – Click Security, SSH, Settings. Enable SSH and adjust the authentication parameters as required, then click Apply. Note that you must first generate the host key pair on the SSH Host-Key Settings page before you can enable the SSH server. Figure 3-37 SSH Server Settings CLI – This example enables SSH, sets the authentication parameters, and displays the current configuration. It shows that the administrator has made a connection via SHH, and then disables this connection.
User Authentication 3 Configuring Port Security Port security is a feature that allows you to configure a switch port with one or more device MAC addresses that are authorized to access the network through that port. When port security is enabled on a port, the switch stops learning new MAC addresses on the specified port when it has reached a configured maximum number.
3 Configuring the Switch Web – Click Security, Port Security. Set the action to take when an invalid address is detected on a port, mark the checkbox in the Status column to enable security for a port, set the maximum number of MAC addresses allowed on a port, and click Apply. Figure 3-38 Port Security CLI – This example selects the target port, sets the port security action to send a trap and disable the port, specifies a maximum address count, and then enables port security for the port.
User Authentication 3 Configuring 802.1X Port Authentication Network switches can provide open and easy access to network resources by simply attaching a client PC. Although this automatic configuration and access is a desirable feature, it also allows unauthorized personnel to easily intrude and possibly gain access to sensitive network data. The IEEE 802.
3 Configuring the Switch • The RADIUS server and client also have to support the same EAP authentication type – MD5. (Some clients have native support in Windows, otherwise the dot1x client must support it.) Displaying 802.1X Global Settings The 802.1X protocol provides port authentication. Command Attributes 802.1X System Authentication Control – The global setting for 802.1X. Web – Click Security, 802.1X, Information. Figure 3-39 802.
User Authentication 3 Configuring 802.1X Global Settings The 802.1X protocol provides port authentication. The 802.1X protocol must be enabled globally for the switch system before port settings are active. Command Attributes 802.1X System Authentication Control – Sets the global setting for 802.1X. (Default: Disabled) Web – Select Security, 802.1X, Configuration. Enable 802.1X globally for the switch, and click Apply. Figure 3-40 802.1X Global Configuration CLI – This example enables 802.
3 Configuring the Switch • Max Request – Sets the maximum number of times the switch port will retransmit an EAP request packet to the client before it times out the authentication session. (Range: 1-10; Default 2) • Quiet Period – Sets the time that a switch port waits after the Max Request count has been exceeded before attempting to acquire a new client.
User Authentication 3 CLI – This example sets the 802.1X parameters on port 2. For a description of the additional fields displayed in this example, see “show dot1x” on page 4-84.
3 Configuring the Switch Displaying 802.1X Statistics This switch can display statistics for dot1x protocol exchanges for any port. Table 3-7 802.1X Statistics Parameter Description Rx EAPOL Start The number of EAPOL Start frames that have been received by this Authenticator. Rx EAPOL Logoff The number of EAPOL Logoff frames that have been received by this Authenticator.
User Authentication 3 Web – Select Security, 802.1X, Statistics. Select the required port and then click Query. Click Refresh to update the statistics. Figure 3-42 802.1X Port Statistics CLI – This example displays the dot1x statistics for port 4.
3 Configuring the Switch Filtering IP Addresses for Management Access You can create a list of up to 16 IP addresses or IP address groups that are allowed management access to the switch through the web interface, SNMP, or Telnet. Command Usage • The management interfaces are open to all IP addresses by default. Once you add an entry to a filter list, access to that interface is restricted to the specified addresses.
User Authentication 3 Web – Click Security, IP Filter. Enter the IP addresses or range of addresses that are allowed management access to an interface, and click Add IP Filtering Entry. Figure 3-43 IP Filter CLI – This example restricts management access for Telnet clients. Console(config)#management telnet-client 192.168.1.19 Console(config)#management telnet-client 192.168.1.25 192.168.1.
3 Configuring the Switch Access Control Lists Access Control Lists (ACL) provide packet filtering for IP frames (based on address, protocol, Layer 4 protocol port number or TCP control code) or any frames (based on MAC address or Ethernet type). To filter incoming packets, first create an access list, add the required rules, specify a mask to modify the precedence in which the rules are checked, and then bind the list to a specific port.
Access Control Lists 3 Setting the ACL Name and Type Use the ACL Configuration page to designate the name and type of an ACL. Command Attributes • Name – Name of the ACL. (Maximum length: 16 characters) • Type – There are three filtering modes: - Standard: IP ACL mode that filters packets based on the source IP address. - Extended: IP ACL mode that filters packets based on source or destination IP address, as well as protocol type and protocol port number.
3 Configuring the Switch and compared with the address for each IP packet entering the port(s) to which this ACL has been assigned. Web – Specify the action (i.e., Permit or Deny). Select the address type (Any, Host, or IP). If you select “Host,” enter a specific address. If you select “IP,” enter a subnet address and the mask for an address range. Then click Add. Figure 3-45 ACL Configuration - Standard IP CLI – This example configures one permit rule for the specific address 10.1.1.
Access Control Lists 3 • Protocol – Specifies the protocol type to match as TCP, UDP or Others, where others indicates a specific protocol number (0-255). (Options: TCP, UDP, Others; Default: TCP) • Source/Destination Port – Source/destination port number for the specified protocol type. (Range: 0-65535) • Source/Destination Port Bit Mask – Decimal number representing the port bits to match.
3 Configuring the Switch Web – Specify the action (i.e., Permit or Deny). Specify the source and/or destination addresses. Select the address type (Any, Host, or IP). If you select “Host,” enter a specific address. If you select “IP,” enter a subnet address and the mask for an address range. Set any other required criteria, such as service type, protocol type, or TCP control code. Then click Add. Figure 3-46 ACL Configuration - Extended IP CLI – This example adds three rules: 1.
Access Control Lists 3 Configuring a MAC ACL Command Attributes • Action – An ACL can contain any combination of permit or deny rules. • Source/Destination Address Type – Use “Any” to include all possible addresses, “Host” to indicate a specific MAC address, or “MAC” to specify an address range with the Address and Bitmask fields. (Options: Any, Host, MAC; Default: Any) • Source/Destination MAC Address – Source or destination MAC address.
3 Configuring the Switch Web – Specify the action (i.e., Permit or Deny). Specify the source and/or destination addresses. Select the address type (Any, Host, or MAC). If you select “Host,” enter a specific address (e.g., 11-22-33-44-55-66). If you select “MAC,” enter a base address and a hexidecimal bitmask for an address range. Set any other required criteria, such as VID, Ethernet type, or packet format. Then click Add.
3 Access Control Lists Configuring ACL Masks You must specify masks that control the order in which ACL rules are checked. The switch includes two system default masks that pass/filter packets matching the permit/deny rules specified in an ingress ACL. You can also configure up to seven user-defined masks for an ingress or egress ACL. A mask must be bound exclusively to one of the basic ACL types (i.e.
3 Configuring the Switch Configuring an IP ACL Mask This mask defines the fields to check in the IP header. Command Usage • Masks that include an entry for a Layer 4 protocol source port or destination port can only be applied to packets with a header length of exactly five bytes. Command Attributes • Source/Destination Address Type – Specifies the source or destination IP address. Use “Any” to match any address, “Host” to specify a host address (not a subnet), or “IP” to specify a range of addresses.
Access Control Lists 3 Web – Configure the mask to match the required rules in the IP ingress or egress ACLs. Set the mask to check for any source or destination address, a specific host address, or an address range. Include other criteria to search for in the rules, such as a protocol type or one of the service types. Or use a bitmask to search for specific protocol port(s) or TCP control code(s). Then click Add.
3 Configuring the Switch Configuring a MAC ACL Mask This mask defines the fields to check in the packet header. Command Usage You must configure a mask for an ACL rule before you can bind it to a port. Command Attributes • Source/Destination Address Type – Use “Any” to match any address, “Host” to specify the host address for a single node, or “MAC” to specify a range of addresses. (Options: Any, Host, MAC; Default: Any) • Source/Destination Bit Mask – Address of rule must match this bitmask.
Access Control Lists 3 CLI – This example shows how to create an Ingress MAC ACL and bind it to a port. You can then see that the order of the rules have been changed by the mask.
3 Configuring the Switch Web – Click Security, ACL, Port Binding. Mark the Enable field for the port you want to bind to an ACL for ingress or egress traffic, select the required ACL from the drop-down list, then click Apply. Figure 3-51 ACL Port Binding CLI – This examples assigns an IP and MAC ingress ACL to port 1, and an IP ingress ACL to port 2.
Port Configuration 3 • Trunk Member8 – Shows if port is a trunk member. • Creation9 – Shows if a trunk is manually configured or dynamically set via LACP. Web – Click Port, Port Information or Trunk Information. Figure 3-52 Port - Port Information Field Attributes (CLI) Basic information: • Port type – Indicates the port type. (100BASE-TX, 1000BASE-T, or SFP) • MAC address – The physical layer address for this port. (To access this item on the web, see “Setting the Switch’s IP Address” on page 3-17.
3 Configuring the Switch • • • • Flow control – Shows if flow control is enabled or disabled. LACP – Shows if LACP is enabled or disabled. Port security – Shows if port security is enabled or disabled. Max MAC count – Shows the maximum number of MAC address that can be learned by a port. (0 - 1024 addresses) • Port security action – Shows the response to take when a security violation is detected. (shutdown, trap, trap-and-shutdown) Current status: • Link status – Indicates if the link is up or down.
Port Configuration 3 Configuring Interface Connections You can use the Port Configuration or Trunk Configuration page to enable/disable an interface, set auto-negotiation and the interface capabilities to advertise, or manually fix the speed and duplex mode, and flow control. Command Attributes • Name – Allows you to label an interface. (Range: 1-64 characters) • Admin – Allows you to manually disable an interface. You can disable an interface due to abnormal behavior (e.g.
3 Configuring the Switch Web – Click Port, Port Configuration or Trunk Configuration. Modify the required interface settings, and click Apply. Figure 3-53 Port - Port Configuration CLI – Select the interface, and then enter the required settings. Console(config)#interface ethernet 1/13 Console(config-if)#description RD SW#13 Console(config-if)#shutdown . Console(config-if)#no shutdown Console(config-if)#no negotiation Console(config-if)#speed-duplex 100half .
Port Configuration 3 Creating Trunk Groups You can create multiple links between devices that work as one virtual, aggregate link. A port trunk offers a dramatic increase in bandwidth for network segments where bottlenecks exist, as well as providing a fault-tolerant link between two devices. You can create up to 12 trunks. The switch supports both static trunking and dynamic Link Aggregation Control Protocol (LACP).
3 Configuring the Switch Statically Configuring a Trunk Command Usage statically configured } • When configuring static trunks, you may not be able to link switches of different types, depending on the manufacturer’s implementation. However, note that the static trunks on this switch are Cisco EtherChannel compatible.
Port Configuration 3 CLI – This example creates trunk 1 with ports 9 and 10. Just connect these ports to two static trunk ports on another switch to form a trunk.
3 Configuring the Switch Command Attributes • Member List (Current) – Shows configured trunks (Unit, Port). • New – Includes entry fields for creating new trunks. - Unit – Stack unit11. (Range: 1-1) - Port – Port identifier. (Range: 1-28) Web – Click Port, LACP, Configuration. Select any of the switch ports from the scroll-down port list and click Add. After you have completed adding ports to the member list, click Apply. Figure 3-55 LACP Trunk Configuration 11.
Port Configuration 3 CLI – The following example enables LACP for ports 1 to 6. Just connect these ports to LACP-enabled trunk ports on another switch to form a trunk. Console(config)#interface ethernet 1/1 4-143 Console(config-if)#lacp 4-159 Console(config-if)#exit . . .
3 Configuring the Switch Configuring LACP Parameters Dynamically Creating a Port Channel – Ports assigned to a common port channel must meet the following criteria: • Ports must have the same LACP System Priority. • Ports must have the same LACP port Admin Key. • However, if the “port channel” Admin Key is set (page 4-142), then the port Admin Key must be set to the same value for a port to be allowed to join a channel group.
Port Configuration 3 Web – Click Port, LACP, Aggregation Port. Set the System Priority, Admin Key, and Port Priority for the Port Actor. You can optionally configure these settings for the Port Partner. (Be aware that these settings only affect the administrative state of the partner, and will not take effect until the next time an aggregate link is formed with this device.) After you have completed setting the port LACP parameters, click Apply.
3 Configuring the Switch CLI – The following example configures LACP parameters for ports 1-10. Ports 1-8 are used as active members of the LAG, ports 9 and 10 are set to backup mode. Console(config)#interface ethernet 1/1 4-143 Console(config-if)#lacp actor system-priority 3 4-160 Console(config-if)#lacp actor admin-key 120 4-161 Console(config-if)#lacp actor port-priority 128 4-162 Console(config-if)#exit . . .
Port Configuration 3 Displaying LACP Port Counters You can display statistics for LACP protocol messages. Table 3-8 LACP Port Counters Parameter Description LACPDUs Sent Number of valid LACPDUs transmitted from this channel group. LACPDUs Received Number of valid LACPDUs received by this channel group. Marker Sent Number of valid Marker PDUs transmitted from this channel group. Marker Received Number of valid Marker PDUs received by this channel group.
3 Configuring the Switch Displaying LACP Settings and Status for the Local Side You can display configuration settings and the operational state for the local side of an link aggregation. Table 3-9 LACP Internal Configuration Information Field Description Oper Key Current operational value of the key for the aggregation port. Admin Key Current administrative value of the key for the aggregation port. LACPDUs Internal Number of seconds before invalidating received LACPDU information.
Port Configuration 3 Web – Click Port, LACP, Port Internal Information. Select a port channel to display the corresponding information. Figure 3-58 LACP - Port Internal Information CLI – The following example displays the LACP configuration settings and operational state for the local side of port channel 1.
3 Configuring the Switch Displaying LACP Settings and Status for the Remote Side You can display configuration settings and the operational state for the remote side of an link aggregation. Table 3-10 LACP Neighbor Configuration Information Field Description Partner Admin System ID LAG partner’s system ID assigned by the user. Partner Oper System ID LAG partner’s system ID assigned by the LACP protocol.
Port Configuration 3 CLI – The following example displays the LACP configuration settings and operational state for the remote side of port channel 1.
3 Configuring the Switch Web – Click Port, Port Broadcast Control or Trunk Broadcast Control. Check the Enabled box for any interface, set the threshold, and click Apply. Figure 3-60 Port Broadcast Control CLI – Specify any interface, and then enter the threshold. The following disables broadcast storm control for port 1, and then sets broadcast suppression at 600 packets per second for port 2.
Port Configuration 3 Configuring Port Mirroring You can mirror traffic from any source port to a target port for real-time analysis. You can then attach a logic analyzer or RMON probe to the target port and study the traffic crossing the source port in a completely unobtrusive manner. Source port(s) Command Usage Single target port • Monitor port speed should match or exceed source port speed, otherwise traffic may be dropped from the monitor port.
3 Configuring the Switch Configuring Rate Limits This function allows the network manager to control the maximum rate for traffic transmitted or received on an interface. Rate limiting is configured on interfaces at the edge of a network to limit traffic into or out of the switch. Traffic that falls within the rate limit is transmitted, while packets that exceed the acceptable amount of traffic are dropped. Rate limiting can be applied to individual ports or trunks.
Port Configuration 3 Showing Port Statistics You can display standard statistics on network traffic from the Interfaces Group and Ethernet-like MIBs, as well as a detailed breakdown of traffic based on the RMON MIB. Interfaces and Ethernet-like statistics display errors on the traffic passing through each port. This information can be used to identify potential problems with the switch (such as a faulty port or unusually heavy loading).
3 Configuring the Switch Table 3-11 Port Statistics (Continued) Parameter Description Transmit Discarded Packets The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Transmit Errors The number of outbound packets that could not be transmitted because of errors.
3 Port Configuration Table 3-11 Port Statistics (Continued) Parameter Description Received Frames The total number of frames (bad, broadcast and multicast) received. Broadcast Frames The total number of good frames received that were directed to the broadcast address. Note that this does not include multicast packets. Multicast Frames The total number of good frames received that were directed to this multicast address.
3 Configuring the Switch Web – Click Port, Port Statistics. Select the required interface, and click Query. You can also use the Refresh button at the bottom of the page to update the screen.
Address Table Settings 3 CLI – This example shows statistics for port 12.
3 Configuring the Switch Web – Click Address Table, Static Addresses. Specify the interface, the MAC address and VLAN, then click Add Static Address. Figure 3-64 Static Addresses CLI – This example adds an address to the static address table, but sets it to be deleted when the switch is reset.
Address Table Settings 3 Web – Click Address Table, Dynamic Addresses. Specify the search type (i.e., mark the Interface, MAC Address, or VLAN checkbox), select the method of sorting the displayed addresses, and then click Query. Figure 3-65 Dynamic Addresses CLI – This example also displays the address table entries for port 1.
3 Configuring the Switch Changing the Aging Time You can set the aging time for entries in the dynamic address table. Command Attributes • Aging Status – Enables/disables the aging function. • Aging Time – The time after which a learned entry is discarded. (Range: 10-1000000 seconds; Default: 300 seconds) Web – Click Address Table, Address Aging. Specify the new aging time, click Apply. Figure 3-66 Address Aging CLI – This example sets the aging time to 400 seconds.
Spanning Tree Algorithm Configuration 3 Designated Root x x x Designated Bridge x Designated Port Root Port x Once a stable network topology has been established, all bridges listen for Hello BPDUs (Bridge Protocol Data Units) transmitted from the Root Bridge. If a bridge does not get a Hello BPDU after a predefined interval (Maximum Age), the bridge assumes that the link to the Root Bridge is down.
3 • • • • • Configuring the Switch new root port is selected from among the device ports attached to the network. (References to “ports” in this section mean “interfaces,” which includes both ports and trunks.) Hello Time – Interval (in seconds) at which the root device transmits a configuration message. Forward Delay – The maximum time (in seconds) the root device will wait before changing states (i.e., discarding to learning to forwarding).
Spanning Tree Algorithm Configuration 3 • Root Forward Delay – The maximum time (in seconds) this device will wait before changing states (i.e., discarding to learning to forwarding). This delay is required because every device must receive information about topology changes before it starts to forward frames. In addition, each port needs time to listen for conflicting information that would make it return to a discarding state; otherwise, temporary data loops might result.
3 Configuring the Switch Transmission limit: 3 Path Cost Method: long --------------------------------------------------------------Eth 1/ 1 information --------------------------------------------------------------Admin status: enabled Role: disable State: discarding External admin path cost: 10000 Internal admin cost: 10000 External oper path cost: 10000 Internal oper path cost: 10000 Priority: 128 Designated cost: 300000 Designated port: 128.1 Designated root: 32768.
Spanning Tree Algorithm Configuration 3 • Multiple Spanning Tree Protocol - To allow multiple spanning trees to operate over the network, you must configure a related set of bridges with the same MSTP configuration, allowing them to participate in a specific set of spanning tree instances. - A spanning tree instance can exist only on bridges that have compatible VLAN instance assignments. - Be careful when switching between spanning tree modes.
3 Configuring the Switch • Forward Delay – The maximum time (in seconds) this device will wait before changing states (i.e., discarding to learning to forwarding). This delay is required because every device must receive information about topology changes before it starts to forward frames. In addition, each port needs time to listen for conflicting information that would make it return to a discarding state; otherwise, temporary data loops might result. • Default: 15 • Minimum: The higher of 4 or [(Max.
Spanning Tree Algorithm Configuration 3 Web – Click Spanning Tree, STA, Configuration. Modify the required attributes, and click Apply.
3 Configuring the Switch CLI – This example enables Spanning Tree Protocol, sets the mode to MST, and then configures the STA and MSTP parameters.
Spanning Tree Algorithm Configuration 3 • Oper Path Cost – The contribution of this port to the path cost of paths towards the spanning tree root which include this port. • Oper Link Type – The operational point-to-point status of the LAN segment attached to this interface. This parameter is determined by manual configuration or by auto-detection, as described for Admin Link Type in STA Port Configuration on page 3-127.
3 Configuring the Switch • Internal path cost – The path cost for the MST. See the preceding item. • Priority – Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops.
Spanning Tree Algorithm Configuration 3 CLI – This example shows the STA attributes for port 5. Console#show spanning-tree ethernet 1/5 Eth 1/ 5 information -------------------------------------------------------------Admin status: enabled Role: disable State: discarding External admin path cost: 10000 Internal admin cost: 10000 External oper path cost: 10000 Internal oper path cost: 10000 Priority: 128 Designated cost: 10000 Designated port: 128.1 Designated root: 32768.0.
3 Configuring the Switch The following interface attributes can be configured: • Spanning Tree – Enables/disables STA on this interface. (Default: Enabled) • Priority – Defines the priority used for this port in the Spanning Tree Protocol. If the path cost for all ports on a switch are the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree.
Spanning Tree Algorithm Configuration 3 Migration button to manually re-check the appropriate BPDU format (RSTP or STP-compatible) to send on the selected interfaces. (Default: Disabled) Web – Click Spanning Tree, STA, Port Configuration or Trunk Configuration. Modify the required attributes, then click Apply. Figure 3-70 STA Port Configuration CLI – This example sets STA attributes for port 7.
3 Configuring the Switch Note: All VLANs are automatically added to the IST (Instance 0). To ensure that the MSTI maintains connectivity across the network, you must configure a related set of bridges with the same MSTI settings. Command Attributes • MST Instance – Instance identifier of this spanning tree. (Default: 0) • Priority – The priority of a spanning tree instance.
Spanning Tree Algorithm Configuration 3 CLI – This displays STA settings for instance 1, followed by settings for each port. Console#show spanning-tree mst 1 Spanning-tree information --------------------------------------------------------------Spanning tree mode: MSTP Spanning tree enabled/disabled: enabled Instance: 1 VLANs configuration: 1 Priority: 32768 Bridge Hello Time (sec.): 2 Bridge Max Age (sec.): 20 Bridge Forward Delay (sec.): 15 Root Hello Time (sec.): 2 Root Max Age (sec.
3 Configuring the Switch Displaying Interface Settings for MSTP The MSTP Port Information and MSTP Trunk Information pages display the current status of ports and trunks in the selected MST instance. Field Attributes MST Instance ID – Instance identifier to configure. (Range: 0-4094; Default: 0) The other attributes are described under “Displaying Interface Settings,” page 3-124. Web – Click Spanning Tree, MSTP, Port Information or Trunk Information.
Spanning Tree Algorithm Configuration 3 --------------------------------------------------------------Eth 1/ 1 information --------------------------------------------------------------Admin status: enabled Role: root State: forwarding External admin path cost: 10000 Internal admin path cost: 10000 External oper path cost: 10000 Internal oper path cost: 10000 Priority: 128 Designated cost: 0 Designated port: 128.4 Designated root: 32768.0.0000E8AAAA00 Designated bridge: 32768.0.
3 Configuring the Switch • Admin MST Path Cost – This parameter is used by the MSTP to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority.) Note that when the Path Cost Method is set to short (page 3-63), the maximum path cost is 65,535.
VLAN Configuration 3 VLAN Configuration IEEE 802.1Q VLANs In large networks, routers are used to isolate broadcast traffic for each subnet into separate domains. This switch provides a similar service at Layer 2 by using VLANs to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This also provides a more secure and cleaner network environment. An IEEE 802.
3 Configuring the Switch Note: VLAN-tagged frames can pass through VLAN-aware or VLAN-unaware network interconnection devices, but the VLAN tags should be stripped off before passing it on to any end-node host that does not support VLAN tagging. tagged frames VA VA VA: VLAN Aware VU: VLAN Unaware tagged frames VA untagged frames VA VU VLAN Classification – When the switch receives a frame, it classifies the frame in one of two ways.
VLAN Configuration 3 these hosts, and core switches in the network, enable GVRP on the links between these devices. You should also determine security boundaries in the network and disable GVRP on the boundary ports to prevent advertisements from being propagated, or forbid those ports from joining restricted VLANs.
3 Configuring the Switch Enabling or Disabling GVRP (Global Setting) GARP VLAN Registration Protocol (GVRP) defines a way for switches to exchange VLAN information in order to register VLAN members on ports across the network. VLANs are dynamically configured based on join messages issued by host devices and propagated throughout the network. GVRP must be enabled to permit automatic VLAN registration, and to support VLANs which extend beyond the local switch. (Default: Disabled) Web – Click VLAN, 802.
3 VLAN Configuration CLI – Enter the following command.
3 Configuring the Switch Command Attributes (CLI) • VLAN – ID of configured VLAN (1-4094, no leading zeroes). • Type – Shows how this VLAN was added to the switch. - Dynamic: Automatically learned via GVRP. - Static: Added as a static entry. • Name – Name of the VLAN (1 to 32 characters). • Status – Shows if this VLAN is enabled or disabled. - Active: VLAN is operational. - Suspend: VLAN is suspended; i.e., does not pass packets. • Ports / Channel groups – Shows the VLAN interface members.
VLAN Configuration 3 Web – Click VLAN, 802.1Q VLAN, Static List. To create a new VLAN, enter the VLAN ID and VLAN name, mark the Enable checkbox to activate the VLAN, and then click Add. Figure 3-77 VLAN Static List - Creating VLANs CLI – This example creates a new VLAN. Console(config)#vlan database Console(config-vlan)#vlan 2 name R&D media ethernet state active Console(config-vlan)#end Console#show vlan VLAN ID: Type: Name: Status: Ports/Port Channels: . . .
3 Configuring the Switch Command Attributes • VLAN – ID of configured VLAN (1-4094). • Name – Name of the VLAN (1 to 32 characters). • Status – Enables or disables the specified VLAN. - Enable: VLAN is operational. - Disable: VLAN is suspended; i.e., does not pass packets. • Port – Port identifier. • Trunk – Trunk identifier. • Membership Type – Select VLAN membership for each interface by marking the appropriate radio button for a port or trunk: - Tagged: Interface is a member of the VLAN.
3 VLAN Configuration CLI – The following example adds tagged and untagged ports to VLAN 2.
3 Configuring the Switch Configuring VLAN Behavior for Interfaces You can configure VLAN behavior for specific interfaces, including the default VLAN identifier (PVID), accepted frame types, ingress filtering, GVRP status, and GARP timers. Command Usage • GVRP – GARP VLAN Registration Protocol defines a way for switches to exchange VLAN information in order to automatically register VLAN members on interfaces across the network.
VLAN Configuration 3 Leave or LeaveAll message has been issued, the applicants can rejoin before the port actually leaves the group. (Range: 60-3000 centiseconds; Default: 60) • GARP LeaveAll Timer19 – The interval between sending out a LeaveAll query message for VLAN group participants and the port leaving the group. This interval should be considerably larger than the Leave Time to minimize the amount of traffic generated by nodes rejoining the group.
3 Configuring the Switch CLI – This example sets port 3 to accept only tagged frames, assigns PVID 3 as the native VLAN ID, enables GVRP, sets the GARP timers, and then sets the switchport mode to hybrid.
3 VLAN Configuration Configuring Uplink and Downlink Ports Use the Private VLAN Link Status page to set ports as downlink or uplink ports. Ports designated as downlink ports can not communicate with any other ports on the switch except for the uplink ports. Uplink ports can communicate with any other ports on the switch and with any designated downlink ports. Web – Click VLAN, Private VLAN, Link Status. Mark the ports that will serve as uplinks and downlinks for the private VLAN, then click Apply.
3 Configuring the Switch Command Usage To configure protocol-based VLANs, follow these steps: 1. First configure VLAN groups for the protocols you want to use (page 3-140). Although not mandatory, we suggest configuring a separate VLAN for each major protocol running on your network. Do not add port members at this time. 2. Create a protocol group for each of the protocols you want to assign to a VLAN using the Protocol VLAN Configuration page. 3.
3 VLAN Configuration Mapping Protocols to VLANs Map a protocol group to a VLAN for each interface that will participate in the group. Command Usage • When creating a protocol-based VLAN, only assign interfaces using this configuration screen. If you assign interfaces using any of the other VLAN menus such as the VLAN Static Table (page 3-141) or VLAN Static Membership by Port menu (page 3-143), these interfaces will admit traffic of any protocol type into the associated VLAN.
3 Configuring the Switch CLI – The following maps the traffic entering Port 1 which matches the protocol type specified in protocol group 1 to VLAN 3. Console(config)#interface ethernet 1/1 Console(config-if)#protocol-vlan protocol-group 1 vlan 3 Console(config-if)# 4-199 Class of Service Configuration Class of Service (CoS) allows you to specify which data packets have greater precedence when traffic is buffered in the switch due to congestion.
Class of Service Configuration 3 Web – Click Priority, Default Port Priority or Default Trunk Priority. Modify the default priority for any interface, then click Apply. Figure 3-85 Default Port Priority CLI – This example assigns a default priority of 5 to port 3.
3 Configuring the Switch Mapping CoS Values to Egress Queues This switch processes Class of Service (CoS) priority tagged traffic by using eight priority queues for each port, with service schedules based on strict or Weighted Round Robin (WRR). Up to eight separate traffic priorities are defined in IEEE 802.1p. The default priority levels are assigned according to recommendations in the IEEE 802.1p standard as shown in the following table.
3 Class of Service Configuration Web – Click Priority, Traffic Classes. Assign priorities to the traffic classes (i.e., output queues), then click Apply. Figure 3-86 Traffic Classes CLI – The following example shows how to change the CoS assignments to a one-to-one mapping.
3 Configuring the Switch Selecting the Queue Mode You can set the switch to service the queues based on a strict rule that requires all traffic in a higher priority queue to be processed before lower priority queues are serviced, or use Weighted Round-Robin (WRR) queuing that specifies a relative weight of each queue. WRR uses a predefined relative weight for each queue that determines the percentage of service time the switch services each queue before moving on to the next queue.
3 Class of Service Configuration Web – Click Priority, Queue Scheduling. Select the interface, highlight a traffic class (i.e., output queue), enter a weight, then click Apply. Figure 3-88 Queue Scheduling CLI – The following example shows how to assign WRR weights to each of the priority queues.
3 Configuring the Switch Layer 3/4 Priority Settings Mapping Layer 3/4 Priorities to CoS Values This switch supports several common methods of prioritizing layer 3/4 traffic to meet application requirements. Traffic priorities can be specified in the IP header of a frame, using the priority bits in the Type of Service (ToS) octet or the number of the TCP port.
Class of Service Configuration 3 Mapping IP Precedence The Type of Service (ToS) octet in the IPv4 header includes three precedence bits defining eight different priority levels ranging from highest priority for network control packets to lowest priority for routine traffic. The default IP Precedence values are mapped one-to-one to Class of Service values (i.e., Precedence value 0 maps to CoS value 0, and so forth).
3 Configuring the Switch CLI – The following example globally enables IP Precedence service on the switch, maps IP Precedence value 1 to CoS value 0 (on port 1), and then displays the IP Precedence settings.
Class of Service Configuration 3 Web – Click Priority, IP DSCP Priority. Select an entry from the DSCP table, enter a value in the Class of Service Value field, then click Apply. Figure 3-91 IP DSCP Priority CLI – The following example globally enables DSCP Priority service on the switch, maps DSCP value 0 to CoS value 1 (on port 1), and then displays the DSCP Priority settings.
3 Configuring the Switch Mapping IP Port Priority You can also map network applications to Class of Service values based on the IP port number (i.e., TCP/UDP port number) in the frame header. Some of the more common TCP service ports include: HTTP: 80, FTP: 21, Telnet: 23 and POP3: 110. Command Attributes • • • • IP Port Priority Status – Enables or disables the IP port priority. IP Port Priority Table – Shows the IP port to CoS map. IP Port Number (TCP/UDP) – Set a new IP port number.
Quality of Service 3 CLI – The following example globally enables IP Port Priority service on the switch, maps HTTP traffic (on port 1) to CoS value 0, and then displays the IP Port Priority settings. Console(config)#map ip port Console(config)#interface ethernet 1/1 Console(config-if)#map ip port 80 cos 0 Console(config-if)#end Console#show map ip port ethernet 1/5 TCP port mapping status: disabled 4-212 4-143 4-212 4-216 Port Port no.
3 Configuring the Switch Configuring Quality of Service Parameters To create a service policy for a specific category or ingress traffic, follow these steps: 1. Use the “Class Map” to designate a class name for a specific category of traffic. 2. Edit the rules for each class to specify a type of traffic based on an access list, a DSCP or IP Precedence value, or a VLAN. 3. Set an ACL mask to enable filtering for the criteria specified in the Class Map.
Quality of Service 3 Command Attributes Class Map • Modify Name and Description – Configures the name and a brief description of a class map. (Range: 1-32 characters for the name; 1-256 characters for the description) • Edit Rules – Opens the “Match Class Settings” page for the selected class entry. Modify the criteria used to classify ingress traffic on this page. • Add Class – Opens the “Class Configuration” page.
3 Configuring the Switch Web – Click QoS, DiffServ, then click Add Class to create a new class, or Edit Rules to change the rules of an existing class. Figure 3-94 Configuring Class Maps CLI - This example creates a class map call “rd-class,” and sets it to match packets marked for DSCP service value 3.
3 Quality of Service Creating QoS Policies This function creates a policy map that can be attached to multiple interfaces. Command Usage • To configure a Policy Map, follow these steps: - Create a Class Map as described on page 3-162. - Open the Policy Map page, and click Add Policy. - When the Policy Configuration page opens, fill in the “Policy Name” field, and click Add. - When the Policy Rule Settings page opens, select a class name from the scroll-down list (Class Name field).
3 Configuring the Switch Policy Rule Settings - Class Settings • Class Name – Name of class map. • Action – Shows the service provided to ingress traffic by setting a CoS, DSCP, or IP Precedence value in a matching packet (as specified in Match Class Settings on page 3-162). • Meter – The maximum throughput and burst rate. - Rate (kbps) – Rate in kilobits per second. - Burst (byte) – Burst in bytes.
Quality of Service 3 Web – Click QoS, DiffServ, Policy Map to display the list of existing policy maps. To add a new policy map click Add Policy. To configure the policy rule settings click Edit Classes.
3 Configuring the Switch CLI – This example creates a policy map called “rd-policy,” sets the average bandwidth the 1 Mbps, the burst rate to 1522 bps, and the response to reduce the DSCP value for violating packets to 0.
Multicast Filtering 3 Multicast Filtering Multicasting is used to support real-time applications such as videoconferencing or streaming audio. A multicast server does not have to establish a separate connection with each client. It merely broadcasts its service to the network, and any hosts that want to receive the multicast register with their local multicast switch/ router.
3 Configuring the Switch Based on the group membership information learned from IGMP, a router/switch can determine which (if any) multicast traffic needs to be forwarded to each of its ports. At Layer 3, multicast routers use this information, along with a multicast routing protocol such as DVMRP or PIM, to support IP multicasting across the Internet. Note that IGMP neither alters nor routes IP multicast packets.
Multicast Filtering 3 Configuring IGMP Snooping and Query Parameters You can configure the switch to forward multicast traffic intelligently. Based on the IGMP query and report messages, the switch forwards traffic only to the ports that request multicast traffic. This prevents the switch from broadcasting the traffic to all ports and possibly disrupting network performance.
3 Configuring the Switch Web – Click IGMP Snooping, IGMP Configuration. Adjust the IGMP settings as required, and then click Apply. (The default settings are shown below.) Figure 3-97 IGMP Configuration CLI – This example modifies the settings for multicast filtering, and then displays the current status.
3 Multicast Filtering Displaying Interfaces Attached to a Multicast Router Multicast routers that are attached to ports on the switch use information obtained from IGMP, along with a multicast routing protocol such as DVMRP or PIM, to support IP multicasting across the Internet. These routers may be dynamically discovered by the switch or statically assigned to an interface on the switch.
3 Configuring the Switch Specifying Static Interfaces for a Multicast Router Depending on your network connections, IGMP snooping may not always be able to locate the IGMP querier. Therefore, if the IGMP querier is a known multicast router/ switch connected over the network to an interface (port or trunk) on your switch, you can manually configure the interface (and a specified VLAN) to join all the current multicast groups supported by the attached router.
Multicast Filtering 3 Displaying Port Members of Multicast Services You can display the port members associated with a specified VLAN and multicast service. Command Attribute • VLAN ID – Selects the VLAN for which to display port members. • Multicast IP Address – The IP address for a specific multicast service. • Multicast Group Port List – Shows the interfaces that have already been assigned to the selected VLAN to propagate a specific multicast service.
3 Configuring the Switch Assigning Ports to Multicast Services Multicast filtering can be dynamically configured using IGMP Snooping and IGMP Query messages as described in “Configuring IGMP Snooping and Query Parameters” on page 3-171. For certain applications that require tighter control, you may need to statically configure a multicast service on the switch. First add all the ports attached to participating hosts to a common VLAN, and then assign the multicast service to that VLAN group.
Multicast Filtering 3 CLI – This example assigns a multicast address to VLAN 1, and then displays all the known multicast services supported on VLAN 1. Console(config)#ip igmp snooping vlan 1 static 224.1.1.12 ethernet 1/12 Console(config)#exit Console#show mac-address-table multicast vlan 1 VLAN M'cast IP addr. Member ports Type ---- --------------- ------------ ------1 224.1.1.12 Eth1/12 USER 1 224.1.2.
3 Configuring the Switch it will continue to receive the multicast service. The following parameters are used to control Layer 3 IGMP and query functions. Command Attributes • VLAN (Interface) – VLAN interface bound to a primary IP address. (Range: 1-4094) • IGMP Protocol Status (Admin Status) – Enables IGMP on a VLAN interface.
Multicast Filtering 3 • Last Member Query Interval – A multicast client sends an IGMP leave message when it leaves a group. The router then checks to see if this was the last host in the group by sending an IGMP query and starting a timer based on this command. If no reports are received before the timer expires, the group is deleted. (Range: 0-25 seconds; Default: 1 second) - This value may be tuned to modify the leave latency of the network.
3 Configuring the Switch Web – Click IP, IGMP, Interface Settings. Specify each interface that will support IGMP (Layer 3), specify the IGMP parameters for each interface, then click Apply. Figure 3-102 IGMP Interface Settings CLI – This example configures the IGMP parameters for VLAN 1.
Multicast Filtering 3 Displaying Multicast Group Information When IGMP (Layer 3) is enabled on this switch the current multicast groups learned via IGMP can be displayed in the IP/IGMP/Group Information page. When IGMP (Layer 3) is disabled and IGMP (Layer 2) is enabled, you can view the active multicast groups in the IGMP Snooping/IP Multicast Registration Table (see page 3-175).
3 Configuring the Switch Configuring Domain Name Service The Domain Naming System (DNS) service on this switch allows host names to be mapped to IP addresses using static table entries or by redirection to other name servers on the network. When a client device designates this switch as a DNS server, the client will attempt to resolve host names into IP addresses by forwarding DNS queries to the switch, and waiting for a response.
Configuring Domain Name Service 3 Web – Select DNS, General Configuration. Set the default domain name or list of domain names, specify one or more name servers to use to use for address resolution, enable domain lookup status, and click Apply. Figure 3-104 DNS General Configuration CLI - This example sets a default domain name and a domain list. However, remember that if a domain list is specified, the default domain name is not used. Console(config)#ip domain-name sample.
3 Configuring the Switch Configuring Static DNS Host to Address Entries You can manually configure static entries in the DNS table that are used to map domain names to IP addresses. Command Usage • Static entries may be used for local devices connected directly to the attached network, or for commonly used resources located elsewhere on the network. • Servers or other network devices may support one or more connections via multiple IP addresses.
Configuring Domain Name Service 3 Web – Select DNS, Static Host Table. Enter a host name and one or more corresponding addresses, then click Apply. Figure 3-105 DNS Static Host Table CLI - This example maps two address to a host name, and then configures an alias host name for the same addresses. Console(config)#ip host rd5 192.168.1.55 10.1.0.55 Console(config)#ip host rd6 10.1.0.55 Console#show host 4-136 4-141 Hostname rd5 Inet address 10.1.0.55 192.168.1.55 Alias 1.
3 Configuring the Switch Displaying the DNS Cache You can display entries in the DNS cache that have been learned via the designated name servers. Field Attributes • No – The entry number for each resource record. • Flag – The flag is always “4” indicating a cache entry and therefore unreliable. • Type – This field includes CNAME which specifies the canonical or primary name for the owner, and ALIAS which specifies multiple domain names which are mapped to the same IP address as an existing entry.
Dynamic Host Configuration Protocol 3 CLI - This example displays all the resource records learned from the designated name servers. Console#show dns cache NO FLAG TYPE 0 4 CNAME 1 4 CNAME 2 4 CNAME 3 4 CNAME 4 4 CNAME 5 4 ALIAS 6 4 CNAME 7 4 ALIAS 8 4 CNAME 9 4 ALIAS 10 4 CNAME Console# IP 207.46.134.222 207.46.134.190 207.46.134.155 207.46.249.222 207.46.249.27 POINTER TO:4 207.46.68.27 POINTER TO:6 65.54.131.192 POINTER TO:8 165.193.72.
3 Configuring the Switch Command Usage You must specify the IP address for at least one DHCP server. Otherwise, the switch’s DHCP relay agent will not forward client requests to a DHCP server. Command Attributes • VLAN ID – ID of configured VLAN. • VLAN Name – Name of the VLAN. • Server IP Address – Addresses of DHCP servers to be used by the switch’s DHCP relay agent in order of preference. • Restart DHCP Relay – Use this button to enable or re-initialize DHCP relay service.
Dynamic Host Configuration Protocol 3 Configuring the DHCP Server This switch includes a Dynamic Host Configuration Protocol (DHCP) server that can assign temporary IP addresses to any attached host requesting service. It can also provide other network settings such as the domain name, default gateway, Domain Name Servers (DNS), Windows Internet Naming Service (WINS) name servers, or information on the bootup file for the host device to download.
3 Configuring the Switch Web – Click DHCP, Server, General. Enter a single address or an address range, and click Add. Figure 3-108 DHCP Server General Configuration CLI – This example enables the DHCP and sets an excluded address range. Console(config)#service dhcp Console(config)#ip dhcp excluded-address 10.1.0.250 10.1.0.
Dynamic Host Configuration Protocol 3 Configuring Address Pools You must configure IP address pools for each IP interface that will provide addresses to attached clients via the DHCP server. Command Usage • First configure address pools for the network interfaces. Then you can manually bind an address to a specific client if required. However, note that any static host address must fall within the range of an existing network address pool.
3 Configuring the Switch • Client-Identifier – A unique designation for the client device, either a text string (1-15 characters) or hexadecimal value. Setting the Optional Parameters • Default Router – The IP address of the primary and alternate gateway router. The IP address of the router should be on the same subnet as the client. • DNS Server – The IP address of the primary and alternate DNS server. DNS servers must be configured for a DHCP client to map host names to IP addresses.
Dynamic Host Configuration Protocol 3 Configuring a Network Address Pool Web – Click DHCP, Server, Pool Configuration. Click the Configure button for any entry. Click the radio button for “Network.” Enter the IP address and subnet mask for the network pool. Configure the optional parameters such as gateway server and DNS server. Then click Apply. Figure 3-110 DHCP Server Pool - Network Configuration CLI – This example configures a network address pool.
3 Configuring the Switch Configuring a Host Address Pool Web – Click DHCP, Server, Pool Configuration. Click the Configure button for any entry. Click the radio button for “Host.” Enter the IP address, subnet mask, and hardware address for the client device. Configure the optional parameters such as gateway server and DNS server. Then click Apply. Figure 3-111 DHCP Server Pool - Host Configuration CLI – This example configures a host address pool.
3 Dynamic Host Configuration Protocol Displaying Address Bindings You can display the host devices which have acquired an IP address from this switch’s DHCP server. Command Attributes • • • • • IP Address – IP address assigned to host. Mac Address – MAC address of host. Lease time – Duration that this IP address can be used by the host. Start time – Time this address was assigned by the switch. Delete – Clears this binding to the host.
3 Configuring the Switch Configuring Router Redundancy Router redundancy protocols use a virtual IP address to support a primary router and multiple backup routers. The backup routers can be configured to take over the workload if the master router fails, or can also be configured to share the traffic load. The primary goal of router redundancy is to allow a host device which has been configured with a fixed gateway to maintain network connectivity in case the primary gateway goes down.
Configuring Router Redundancy 3 • Several virtual master routers configured for mutual backup and load sharing. Load sharing can be accomplished by assigning a subset of addresses to different host address pools using the DHCP server. (See “Configuring Address Pools” on page 3-191.) Router 1 Router 2 VRID 23 (Master) IP(R1) = 192.168.1.3 IP(VR23) = 192.168.1.3 VR Priority = 255 VRID 23 (Backup) IP(R1) = 192.168.1.5 IP(VR23) = 192.168.1.3 VR Priority = 100 VRID 25 (Backup) IP(R1) = 192.168.1.
3 Configuring the Switch • VRRP creates a virtual MAC address for the master router based on a standard prefix, with the last octet equal to the group ID. When a backup router takes over as the master, it continues to forward traffic addressed to this virtual MAC address. However, the backup router cannot reply to ICMP pings sent to addresses associated with the virtual group because the IP address owner is off line.
Configuring Router Redundancy 3 Command Attributes (VRRP Group Configuration Detail) • Associated IP Table – IP interfaces associated with this virtual router group. • Associated IP – IP address of the virtual router, or secondary IP addresses assigned to the current VLAN interface that are supported by this VRRP group. If this address matches a real interface on this switch, then this interface will become the virtual master router for this VRRP group.
3 Configuring the Switch Web – Click IP, VRRP, Group Configuration. Select the VLAN ID, enter the VRID group number, and click Add.
Configuring Router Redundancy 3 Click the Edit button for a group entry to open the detailed configuration window. Enter the IP address of a real interface on this router to make it the master virtual router for the group. Otherwise, enter the virtual address for an existing group to make it a backup router. Click Add IP to enter an IP address into the Associated IP Table. Then set any of the other parameters as required, and click Apply.
3 Configuring the Switch CLI – This example creates VRRP group 1, sets this switch as the master virtual router by assigning the primary interface address for the selected VLAN to the virtual IP address. It then adds a secondary IP address to the VRRP group, sets all of the other VRRP parameters, and then displays the configured settings. Console(config)#interface vlan 1 Console(config-if)#vrrp 1 ip 192.168.1.6 Console(config-if)#vrrp 1 ip 192.168.2.
Configuring Router Redundancy 3 CLI – This example displays counters for protocol errors for all the VRRP groups configured on this switch. Console#show vrrp router counters VRRP Packets with Invalid Checksum : 0 VRRP Packets with Unknown Error : 0 VRRP Packets with Invalid VRID : 0 Console# 4-324 Displaying VRRP Group Statistics The VRRP Group Statistics page displays counters for VRRP protocol events and errors that have occurred on a specific VRRP interface.
3 Configuring the Switch Web – Click IP, VRRP, Group Statistics. Select the VLAN and virtual router group. Figure 3-116 VRRP Group Statistics CLI – This example displays VRRP protocol statistics for group 1, VLAN 1.
IP Routing 3 IP Routing Overview This switch supports IP routing and routing path management via static routing definitions (page 3-223) and dynamic routing such as RIP (page 3-225) or OSPF (page 3-235). When IP routing is enabled (page 3-226), this switch acts as a wire-speed router, passing traffic between VLANs using different IP interfaces, and routing traffic to external IP networks. However, when the switch is first booted, no default routing is defined.
3 Configuring the Switch IP Switching IP Switching (or packet forwarding) encompasses tasks required to forward packets for both Layer 2 and Layer 3, as well as traditional routing.
IP Routing 3 the high throughput and low latency of switching by enabling the traffic to bypass the routing engine once the path calculation has been performed. Routing Path Management Routing Path Management involves the determination and updating of all the routing information required for packet forwarding, including: • Handling routing protocols • Updating the routing table • Updating the Layer 3 switching database Routing Protocols The switch supports both static and dynamic routing.
3 Configuring the Switch Basic IP Interface Configuration To allow routing between different IP subnets, you must enable IP Routing as described in this section. You also need to you define a VLAN for each IP subnet that will be connected directly to this switch. Note that you must first create a VLAN as described under “Creating VLANs” on page 3-140 before configuring the corresponding subnet.
IP Routing 3 Configuring IP Routing Interfaces You can specify the IP subnets connected to this router by manually assigning an IP address to each VLAN, or by using the RIP or OSPF dynamic routing protocol to identify routes that lead to other interfaces by exchanging protocol messages with other routers on the network.
3 Configuring the Switch Web - Click IP, General, Routing Interface. Specify an IP interface for each VLAN that will support routing to other subnets. First specify a primary address, and click Set IP Configuration. If you need to assign secondary addresses, enter these addresses one at a time, and click Set IP Configuration after entering each address.
IP Routing 3 Address Resolution Protocol If IP routing is enabled (page 3-208), the router uses its routing tables to make routing decisions, and uses Address Resolution Protocol (ARP) to forward traffic from one hop to the next. ARP is used to map an IP address to a physical layer (i.e., MAC) address. When an IP frame is received by this router (or any standardsbased router), it first looks up the MAC address corresponding to the destination IP address in the ARP cache.
3 Configuring the Switch Basic ARP Configuration You can use the ARP General configuration menu to specify the timeout for ARP cache entries, or to enable Proxy ARP for specific VLAN interfaces. Command Usage • The aging time determines how long dynamic entries remain the cache. If the timeout is too short, the router may tie up resources by repeating ARP requests for addresses recently flushed from the table. • End stations that require Proxy ARP must view the entire network as a single network.
3 IP Routing Configuring Static ARP Addresses For devices that do not respond to ARP requests, traffic will be dropped because the IP address cannot be mapped to a physical address. If this occurs, you can manually map an IP address to the corresponding physical address in the ARP. Command Usage • You can define up to 128 static entries in the ARP cache. • Static entries will not be aged out or deleted when power is reset. You can only remove a static entry via the configuration interface.
3 Configuring the Switch Displaying Dynamically Learned ARP Entries The ARP cache contains entries that map IP addresses to the corresponding physical address. Most of these entries will be dynamically learned through replies to broadcast messages. You can display all of the dynamic entries in the ARP cache, change specific dynamic entries into static entries, or clear all dynamic entries from the cache. Command Attributes • IP Address – IP address of a dynamic entry in the cache.
IP Routing 3 CLI - This example shows all entries in the ARP cache. Console#show arp Arp cache timeout: 1200 (seconds) IP Address --------------10.1.0.0 10.1.0.11 10.1.0.12 10.1.0.19 10.1.0.253 10.1.0.
3 Configuring the Switch CLI - This router uses the Type specification “other” to indicate local cache entries in the ARP cache. Console#show arp Arp cache timeout: 1200 (seconds) IP Address --------------10.1.0.0 10.1.0.11 10.1.0.12 10.1.0.19 10.1.0.253 10.1.0.
IP Routing 3 CLI - This example provides detailed statistics on common IP-related protocols.
3 Configuring the Switch Table 3-18 IP Statistics (Continued) Parameter Description Datagrams Forwarded The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. Reassembly Required The number of IP fragments received which needed to be reassembled at this entity.
IP Routing 3 Web - Click IP, Statistics, IP. Figure 3-124 IP Statistics CLI - See the example on page 3-216. ICMP Statistics Internet Control Message Protocol (ICMP) is a network layer protocol that transmits message packets to report errors in processing IP packets. ICMP is therefore an integral part of the Internet Protocol.
3 Configuring the Switch Table 3-19 ICMP Statistics (Continued) Parameter Description Timestamps The number of ICMP Timestamp (request) messages received/sent. Timestamp Replies The number of ICMP Timestamp Reply messages received/sent. Address Masks The number of ICMP Address Mask Request messages received/sent. Address Mask Replies The number of ICMP Address Mask Reply messages received/sent. Web - Click IP, Statistics, ICMP. Figure 3-125 ICMP Statistics CLI - See the example on page 3-216.
IP Routing 3 UDP Statistics User Datagram Protocol (UDP) provides a datagram mode of packet-switched communications. It uses IP as the underlying transport mechanism, providing access to IP-like services. UDP packets are delivered just like IP packets – connection-less datagrams that may be discarded before reaching their targets. UDP is useful when TCP would be too complex, too slow, or just unnecessary.
3 Configuring the Switch TCP Statistics The Transmission Control Protocol (TCP) provides highly reliable host-to-host connections in packet-switched networks, and is used in conjunction with IP to support a wide variety of Internet protocols. Table 3-21 TCP Statistics Parameter Description Segments Received The total number of segments received, including those received in error. This count includes segments received on currently established connections.
IP Routing 3 Configuring Static Routes This router can dynamically configure routes to other network segments using dynamic routing protocols (i.e., RIP or OSPF). However, you can also manually enter static routes in the routing table. Static routes may be required to access network segments where dynamic routing is not supported, or can be set to force the use of a specific route to a subnet, rather than using dynamic routing.
3 Configuring the Switch Displaying the Routing Table You can display all the routes that can be accessed via the local network interfaces, via static routes, or via a dynamically learned route. If route information is available through more than one of these methods, the priority for route selection is local, static, and then dynamic. Also note that the route for a local interface is not enabled (i.e., listed in the routing table) unless there is at least one active link connected to that interface.
IP Routing 3 CLI - This example shows routes obtained from various methods. Console#show ip route 4-253 Ip Address Netmask Next Hop Protocol Metric Interface --------------- --------------- --------------- -------- ------ --------0.0.0.0 0.0.0.0 10.1.0.254 static 1 1 10.1.0.0 255.255.255.0 10.1.0.253 local 1 1 10.1.1.0 255.255.255.0 10.1.0.254 RIP 2 1 Total entries: 3 Console# Configuring the Routing Information Protocol The RIP protocol is the most widely used routing protocol.
3 Configuring the Switch routing loops may occur, and its small hop count limitation of 15 restricts its use to smaller networks. Moreover, RIP (version 1) wastes valuable network bandwidth by propagating routing information via broadcasts; it also considers too few network variables to make the best routing decision. Configuring General Protocol Settings RIP is used to specify how routers exchange routing information.
IP Routing 3 Web - Click Routing Protocol, RIP, General Settings. Enable or disable RIP, set the RIP version used on previously unset interfaces to RIPv1 or RIPv2, set the basic update timer, and then click Apply. Figure 3-130 RIP General Settings CLI - This example sets the router to use RIP Version 2, and sets the basic timer to 15 seconds.
3 Configuring the Switch Specifying Network Interfaces for RIP You must specify network interfaces that will be included in the RIP routing process. Command Usage • RIP only sends updates to interfaces specified by this command. • Subnet addresses are interpreted as class A, B or C, based on the first field in the specified address. In other words, if a subnet address nnn.xxx.xxx.
IP Routing 3 Configuring Network Interfaces for RIP For each interface that participates in the RIP routing process, you must specify the protocol message type accepted (i.e., RIP version) and the message type sent (i.e., RIP version or compatibility mode), the method for preventing loopback of protocol messages, and whether or not authentication is used (i.e., authentication only applies if RIPv2 messages are being sent or received).
3 Configuring the Switch Protocol Message Authentication RIPv1 is not a secure protocol. Any device sending protocol messages from UDP port 520 will be considered a router by its neighbors. Malicious or unwanted protocol messages can be easily propagated throughout the network if no authentication is required. RIPv2 supports authentication via a simple password.
IP Routing 3 • Authentication Key – Specifies the key to use for authenticating RIPv2 packets. For authentication to function properly, both the sending and receiving interface must use the same password. (Range: 1-16 characters, case sensitive) Web - Click Routing Protocol, RIP, Interface Settings. Select the RIP protocol message types that will be received and sent, the method used to provide faster convergence and prevent loopback (i.e.
3 Configuring the Switch Displaying RIP Information and Statistics You can display basic information about the current global configuration settings for RIP, statistics about route changes and queries, information about the interfaces on this router that are using RIP, and information about known RIP peer devices. Table 3-22 RIP Information and Statistics Parameter Description Globals RIP Routing Process Indicates if RIP has been enabled or disabled.
IP Routing 3 Web - Click Routing Protocol, RIP, Statistics.
3 Configuring the Switch CLI - The information displayed by the RIP Statistics screen via the web interface can be accessed from the CLI using the following commands. Console#show rip globals 4-264 RIP Process: Enabled Update Time in Seconds: 30 Number of Route Change: 4 Number of Queries: 0 Console#show ip rip configuration 4-264 Interface SendMode ReceiveMode Poison Authentication --------------- --------------- ------------- -------------- -----------------10.1.0.
IP Routing 3 Configuring the Open Shortest Path First Protocol Open Shortest Path First (OSPF) is more suited for large area networks which experience frequent changes in the links. It also handles subnets much better than RIP. OSPF protocol actively tests the status of each link to its neighbors to generate a shortest path tree, and builds a routing table based on this information. OSPF then utilizes IP multicast to propagate routing information.
3 Configuring the Switch • OSPFv2 is a compatible upgrade to OSPF. It involves enhancements to protocol message authentication, and the addition of a point-to-multipoint interface which allows OSPF to run over non-broadcast networks, as well as support for overlapping area ranges. • When using OSPF, you must organize your network (i.e.
3 IP Routing • AS Boundary Router 29 – Allows this router to exchange routing information with boundary routers in other autonomous systems to AS 2 AS 1 ASBR ASBR which it may be attached. If a router is enabled as an ASBR, then every other router in the autonomous system can learn about external routes from this device.
3 Configuring the Switch Web - Click Routing Protocol, OSPF, General Configuration. Enable OSPF, specify the Router ID, configure the other global parameters as required, and click Apply. Figure 3-134 OSPF General Configuration CLI - This example configures the router with the same settings as shown in the screen capture for the web interface. Console(config)#router ospf Console(config-router)#router-id 10.1.1.
IP Routing 3 Configuring OSPF Areas An autonomous system must be configured with a backbone area, designated by area identifier 0.0.0.0. By default, all other areas are created as normal transit areas. Routers in a normal area may import or export routing information about individual nodes. To reduce the amount of routing traffic flooded onto the network, you can configure an area to export a single summarized route that covers a broad range of network addresses within the area (page 3-242).
3 Configuring the Switch default external route for another routing domain 5 backbone 7 ABR NSSA ASBR Router default external route for local AS external network AS • Routes that can be advertised with NSSA external LSAs include network destinations outside the AS learned via OSPF, the default route, static routes, routes derived from other routing protocols such as RIP, or directly connected networks that are not running OSPF.
IP Routing 3 Web - Click Routing Protocol, OSPF, Area Configuration. Set any area to a stub or NSSA as required, specify the cost for the default summary route sent into a stub, and click Apply. Figure 3-135 OSPF Area Configuration CLI - This example configures area 0.0.0.1 as a normal area, area 0.0.0.2 as a stub, and area 0.0.0.3 as an NSSA. It also configures the router to propagate a default summary route into the stub and sets the cost for this default route to 10.
3 Configuring the Switch Console#show ip ospf Routing Process with ID 192.168.1.253 Supports only single TOS(TOS0) route Number of area in this router is 3 Area 0.0.0.0 (BACKBONE) Number of interfaces in this area is 1 SPF algorithm executed 40 times Area 0.0.0.2 (STUB) Number of interfaces in this area is 1 SPF algorithm executed 8 times Area 0.0.0.
IP Routing 3 Web - Click Routing Protocol, OSPF, Area Range Configuration. Specify the area identifier, the base address and network mask, select whether or not to advertise the summary route to other areas, and then click Apply. Figure 3-136 OSPF Range Configuration CLI - This example summarizes all the routes for area 1. Note that the default for the area range command is to advertise the route summary. The configured summary route is shown in the list of information displayed for area 1.
3 Configuring the Switch Configuring OSPF Interfaces You should specify a routing interface for any local subnet that needs to communicate with other network segments located on this router or elsewhere in the network. First configure a VLAN for each subnet that will be directly connected to this router, assign IP interfaces to each VLAN (i.e.
IP Routing 3 - On slow links, the router may send packets more quickly than devices can receive them. To avoid this problem, you can use the transmit delay to force the router to wait a specified interval between transmissions. • Retransmit Interval – Sets the time between resending link-state advertisements. (Range: 1-65535 seconds; Default: 1) - A router will resend an LSA to a neighbor if it receives no acknowledgment.
3 Configuring the Switch - You can assign a unique password to each network (i.e., autonomous system) to improve the security of the routing database. However, the password must be used consistently on all neighboring routers throughout a network. • Message Digest Key-id – Assigns a key-id used in conjunction with the authentication key to verify the authenticity of routing protocol messages sent to neighboring routers.
3 IP Routing Change any of the interface-specific protocol parameters, and then click Apply. Figure 3-138 OSPF Interface Configuration - Detailed CLI - This example configures the interface parameters for VLAN 1.
3 Configuring the Switch Configuring Virtual Links All OSPF areas must connect to the backbone. If an area does not have a direct physical connection to the isolated backbone, you can configure a area virtual link that provides a logical path to the backbone. To connect an isolated area to the backbone, the ABR logical path can cross a single non-backbone area (i.e., transit area) virtual link to reach the backbone.
IP Routing 3 Web - Click Routing Protocol, OSPF, Virtual Link Configuration. To create a new virtual link, specify the Area ID and Neighbor Router ID, configure the link attributes, and click Add. To modify the settings for an existing link, click the Detail button for the required entry, modify the link settings, and click Set. Figure 3-139 OSPF Virtual Link Configuration CLI - This example configures a virtual link from the ABR adjacent to area 0.0.0.
3 Configuring the Switch Configuring Network Area Addresses OSPF protocol broadcast messages (i.e., Link State Advertisements or LSAs) are restricted by area to limit their impact on network performance. A large network should be split up into separate OSPF areas to increase network stability, and to reduce protocol traffic by summarizing routing information into more compact messages.
IP Routing 3 Web - Click Routing Protocol, OSPF, Network Area Address Configuration. Configure a backbone area that is contiguous with all the other areas in your network, configure an area for all of the other OSPF interfaces, then click Apply.
3 Configuring the Switch CLI - This example configures the backbone area and one transit area. Console(config-router)#network 10.0.0.0 255.0.0.0 area 0.0.0.0 Console(config-router)#network 10.1.1.0 255.255.255.0 area 0.0.0.1 Console(config-router)#end Console#show ip ospf Routing Process with ID 10.1.1.253 Supports only single TOS(TOS0) route Number of area in this router is 4 Area 0.0.0.0 (BACKBONE) Number of interfaces in this area is 1 SPF algorithm executed 8 times Area 0.0.0.
IP Routing 3 Configuring Summary Addresses (for External AS Routes) An Autonomous System Boundary Router (ASBR) can redistribute routes learned from other protocols into all attached autonomous systems. (See “Redistributing External Routes” on page 3-254) To reduce the amount of external LSAs imported into your local routing domain, you can configure the router to advertise an aggregate route that consolidates a broad range of external addresses.
3 Configuring the Switch CLI - This example This example creates a summary address for all routes contained in 192.168.x.x. Console(config-router)#summary-address 192.168.0.0 255.255.0.0 Console(config-router)# 4-272 Redistributing External Routes You can configure this router to import external routing information from other routing protocols into the autonomous system. Router ASBR OSPF AS RIP, or static routes Command Usage • This router supports redistribution for both RIP and static routes.
3 IP Routing Web - Click Routing Protocol, OSPF, Redistribute. Specify the protocol type to import, the metric type and path cost, then click Add. Figure 3-142 OSPF Redistribute Configuration CLI - This example redistributes routes learned from RIP as Type 1 external routes.
3 Configuring the Switch Note: This router supports up 16 areas, either normal transit areas, stubs, or NSSAs. Web - Click Routing Protocol, OSPF, NSSA Settings. Create a new NSSA or modify the routing behavior for an existing NSSA, and click Apply. Figure 3-143 OSPF NSSA Settings CLI - This example configures area 0.0.0.1 as a stub and sets the cost for the default summary route to 10. Console(config-router)#area 0.0.0.1 nssa default-information- originate Console(config-router)#area 0.0.0.
IP Routing 3 Displaying Link State Database Information OSPF routers advertise routes using Link State Advertisements (LSAs). The full collection of LSAs collected by a router interface from the attached area is known as a link state database. Routers that are connected to multiple interfaces will have a separate database for each area. Each router in the same area should have an identical database describing the topology for that area, and the shortest path to external destinations.
3 Configuring the Switch Web - Click Routing Protocol, OSPF, Link State Database Information. Specify parameters for the LSAs you want to display, then click Query. Figure 3-144 OSPF Link State Database Information CLI - The CLI provides a wider selection of display options for viewing the Link State Database. See “show ip ospf database” on page 4-286.
IP Routing 3 Displaying Information on Border Routers You can display entries in the local routing table for Area Border Routers (ABR) and Autonomous System Boundary Routers (ASBR) known by this device. Field Attributes • • • • • • • Destination – Identifier for the destination router. Next Hop – IP address of the next hop toward the destination. Cost – Link metric for this route. Type – Router type of the destination; either ABR, ASBR or both.
3 Configuring the Switch Displaying Information on Neighbor Routers You can display about neighboring routers on each interface within an OSPF area. Field Attributes • ID – Neighbor’s router ID. • Priority – Neighbor’s router priority. • State – OSPF state and identification flag.
Multicast Routing 3 Multicast Routing This router can route multicast traffic to different subnetworks using either Distance Vector Multicast Routing Protocol (DVMRP) or Protocol-Independent Multicasting Dense Mode (PIM-DM). These protocols flood multicast traffic downstream, and calculate the shortest-path, source-rooted delivery tree between each source and destination host group.
3 Configuring the Switch Displaying the Multicast Routing Table You can display information on each multicast route this router has learned via DVMRP or PIM. The router learns multicast routes from neighboring routers, and also advertises these routes to its neighbors. The router stores entries for all paths learned by itself or from other routers, without considering actual group membership or prune messages.
Multicast Routing 3 Web – Click IP, Multicast Routing, Multicast Routing Table. Click Detail to display additional information for any entry.
3 Configuring the Switch CLI – This example shows that multicast forwarding is enabled. The multicast routing table displays one entry for a multicast source routed by DVMRP, and another source routed via PIM. Console#show ip mroute IP Multicast Forwarding is enabled. IP Multicast Routing Table Flags: P - Prune, F - Forwarding (234.5.6.7, 10.1.0.0, 255.255.255.0) Owner: DVMRP Upstream Interface: vlan2 Upstream Router: 10.1.0.0 Downstream: (234.5.6.8, 10.1.5.19, 255.255.255.
Multicast Routing 3 Configuring DVMRP The Distance-Vector Multicast Routing Protocol (DVMRP) behaves somewhat similarly to RIP. A router supporting DVMRP periodically floods its attached networks to pass information about supported multicast services along to new routers and hosts. Routers that receive a DVMRP packet send a copy out to all paths (except the path back to the origin).
3 Configuring the Switch Command Usage Broadcasting periodically floods the network with traffic from any active multicast server. If IGMP snooping is disabled, multicast traffic is flooded to all ports on the router. However, if IGMP snooping is enabled, then the first packet for any source group pair is flooded to all DVMRP downstream neighbors.
Multicast Routing • • • • 3 which this device has received probes, and is used to verify whether or not these neighbors are still active members of the multicast tree. (Range: 1-65535 seconds; Default: 10 seconds) Neighbor Timeout Interval – Sets the interval to wait for messages from a DVMRP neighbor before declaring it dead. This command is used for timing out routes, and for setting the children and leaf flags.
3 Configuring the Switch Web – Click Routing Protocol, DVMRP, General Settings. Enable or disable DVMRP. Set the global parameters that control neighbor timeout, the exchange of routing information, or the prune lifetime, and click Apply. Figure 3-149 DVMRP General Settings CLI – This sets the global parameters for DVMRP and displays the current settings.
Multicast Routing 3 DVMRP Interface Settings • VLAN – Selects a VLAN interface on this router. • Metric – Sets the metric for this interface used to calculate distance vectors. • Status – Enables or disables DVMRP. - If DVMRP is enabled on any interface, Layer 3 IGMP should also be enabled on the router (page 3-177). - If DVMRP is disabled, the interface cannot propagate IP multicast routing information.
3 Configuring the Switch Displaying Neighbor Information You can display all the neighboring DVMRP routers. Command Attributes • Neighbor Address – The IP address of the network device immediately upstream for this multicast delivery tree. • Interface – The IP interface on this router that connects to the upstream neighbor. • Up time – The time since this device last became a DVMRP neighbor to this router. • Expire – The time remaining before this entry will be aged out.
Multicast Routing 3 Displaying the Routing Table The router learns source-routed information from neighboring DVMRP routers and also advertises learned routes to its neighbors. The router merely records path information it has learned on its own or from other routers. It does not consider group membership or prune messages.
3 Configuring the Switch CLI – This example displays known DVMRP routes. Console#show ip dvmrp route 4-308 Source Mask Upstream_nbr Interface Metric UpTime Expire --------------- --------------- --------------- --------- ------ ------ -----10.1.0.0 255.255.255.0 10.1.0.253 vlan1 1 84438 0 10.1.1.0 255.255.255.0 10.1.1.253 vlan2 1 84987 0 10.1.8.0 255.255.255.0 10.1.0.
Multicast Routing 3 Web – Click Routing Protocol, PIM-DM, General Settings. Enable or disable PIM-DM globally for the router, and click Apply. Figure 3-153 PIM-DM General Settings CLI – This example enables PIM-DM globally and displays the current status.
3 Configuring the Switch • Trigger Hello Interval – Configures the maximum time before transmitting a triggered PIM hello message after the router is rebooted or PIM is enabled on an interface. (Range: 1-65535 seconds; Default: 5) - When a router first starts or PIM is enabled on an interface, the hello-interval is set to random value between 0 and the Trigger Hello Interval. This prevents synchronization of Hello messages on multi-access links if multiple routers are powered on simultaneously.
Multicast Routing 3 Web – Click Routing Protocol, PIM-DM, Interface Settings. Select a VLAN, enable or disable PIM-DM for the selected interface, modify any of the protocol parameters as required, and click Apply. Figure 3-154 PIM-DM Interface Settings CLI – This example sets the PIM-DM protocol parameters for VLAN 2, and displays the current settings.
3 Configuring the Switch Displaying Interface Information You can display a summary of the current interface status for PIM-DM, including the number of neighboring PIM routers, and the address of the designated PIM router. Command Attributes • • • • • Interface – A VLAN interface on this router. Address – The IP address for this interface. Mode – The PIM mode in use. (This router only supports Dense Mode at this time.) Neighbor Count – The number of PIM neighbors detected on this interface.
Multicast Routing 3 Web – Click Routing Protocol, PIM-DM, Neighbor Information. Figure 3-156 PIM-DM Neighbor Information CLI – This example displays the only neighboring PIM-DM router. Console#show ip pim neighbor Address VLAN Interface Uptime Expire Mode --------------- ---------------- -------- -------- ------10.1.0.
3 3-278 Configuring the Switch
Chapter 4: Command Line Interface This chapter describes how to use the Command Line Interface (CLI). Using the Command Line Interface Accessing the CLI When accessing the management interface for the switch over a direct connection to the server’s console port, or via a Telnet connection, the switch can be managed by entering command keywords and parameters at the prompt. Using the switch's command-line interface (CLI) is very similar to entering commands on a UNIX system.
4 Command Line Interface To access the switch through a Telnet session, you must first set the IP address for the switch, and set the default gateway if you are managing the switch from a different IP subnet. For example, Console(config)#interface vlan 1 Console(config-if)#ip address 10.1.0.254 255.255.255.0 Console(config-if)#exit Console(config)#ip default-gateway 10.1.0.
Entering Commands 4 Entering Commands This section describes how to enter CLI commands. Keywords and Arguments A CLI command is a series of keywords and arguments. Keywords identify a command, and arguments specify configuration parameters. For example, in the command “show interfaces status ethernet 1/5,” show interfaces and status are keywords, ethernet is an argument that specifies the interface type, and 1/5 specifies the unit/port.
4 Command Line Interface Showing Commands If you enter a “?” at the command prompt, the system will display the first level of keywords for the current command class (Normal Exec or Privileged Exec) or configuration class (Global, ACL, DHCP, Interface, Line, Router, VLAN Database, or MSTP). You can also display a list of valid keywords for a specific command.
Entering Commands 4 The command “show interfaces ?” will display the following information: Console#show interfaces ? counters Information of interfaces counters protocol-vlan Protocol-vlan information status Information of interfaces status switchport Information of interfaces switchport Console# Partial Keyword Lookup If you terminate a partial keyword with a question mark, alternatives that match the initial letters are provided. (Remember not to leave a space between the command and question mark.
4 Command Line Interface Understanding Command Modes The command set is divided into Exec and Configuration classes. Exec commands generally display information on system status or clear statistical counters. Configuration commands, on the other hand, modify interface parameters or enable certain switching functions. These classes are further divided into different modes. Available commands depend on the selected mode.
Entering Commands 4 Username: guest Password: [guest login password] CLI session with the ES3628C Intelligent Standalone Switch is opened. To end the CLI session, enter [Exit]. Console>enable Password: [privileged level password] Console# Configuration Commands Configuration commands are privileged level commands used to modify switch settings. These commands modify the running configuration only and are not saved when the switch is rebooted.
4 Command Line Interface To enter the other modes, at the configuration prompt type one of the following commands. Use the exit or end command to return to the Privileged Exec mode.
Entering Commands 4 Command Line Processing Commands are not case sensitive. You can abbreviate commands and parameters as long as they contain enough letters to differentiate them from any other currently available commands or parameters. You can use the Tab key to complete partial commands, or enter a partial command followed by the “?” character to display a list of possible matches.
4 Command Line Interface Command Groups The system commands can be broken down into the functional groups shown below.
4 Line Commands Table 4-4 Command Group Index (Continued) Command Group Description Multicast Routing Configures multicast routing protocols DVMRP and PIM-DM Page 4-297 Router Redundancy Configures router redundancy to create primary and backup routers 4-316 The access mode shown in the following tables is indicated by these abbreviations: NE (Normal Exec) PE (Privileged Exec) GC (Global Configuration) LC (Line Configuration) IC (Interface Configuration) VC (VLAN Database Configuration) MST (Multi
4 Command Line Interface line This command identifies a specific line for configuration, and to process subsequent line configuration commands. Syntax line {console | vty} • console - Console terminal line. • vty - Virtual terminal for remote console access (i.e., Telnet). Default Setting There is no default line. Command Mode Global Configuration Command Usage Telnet is considered a virtual terminal connection and will be shown as “VTY” in screen displays such as show users.
Line Commands 4 Command Usage • There are three authentication modes provided by the switch itself at login: - login selects authentication by a single global password as specified by the password line configuration command. When using this method, the management interface starts in Normal Exec (NE) mode. - login local selects authentication via the user name and password specified by the username command (i.e., default setting).
4 Command Line Interface • The encrypted password is required for compatibility with legacy password settings (i.e., plain text or encrypted) when reading the configuration file during system bootup or when downloading the configuration file from a TFTP server. There is no need for you to manually configure encrypted passwords.
Line Commands 4 exec-timeout This command sets the interval that the system waits until user input is detected. Use the no form to restore the default. Syntax exec-timeout [seconds] no exec-timeout seconds - Integer that specifies the timeout interval.
4 Command Line Interface Command Usage • When the logon attempt threshold is reached, the system interface becomes silent for a specified amount of time before allowing the next logon attempt. (Use the silent-time command to set this interval.) When this threshold is reached for Telnet, the Telnet logon interface shuts down. • This command applies to both the local console and Telnet connections.
Line Commands 4 databits This command sets the number of data bits per character that are interpreted and generated by the console port. Use the no form to restore the default value. Syntax databits {7 | 8} no databits • 7 - Seven data bits per character. • 8 - Eight data bits per character. Default Setting 8 data bits per character Command Mode Line Configuration Command Usage The databits command can be used to mask the high bit on input from devices that generate 7 data bits with parity.
4 Command Line Interface Command Usage Communication protocols provided by devices such as terminals and modems often require a specific parity bit setting. Example To specify no parity, enter this command: Console(config-line)#parity none Console(config-line)# speed This command sets the terminal line’s baud rate. This command sets both the transmit (to terminal) and receive (from terminal) speeds. Use the no form to restore the default setting.
Line Commands 4 Default Setting 1 stop bit Command Mode Line Configuration Example To specify 2 stop bits, enter this command: Console(config-line)#stopbits 2 Console(config-line)# disconnect This command terminates an SSH, Telnet, or console connection. Syntax disconnect session-id session-id – The session identifier for an SSH, Telnet or console connection. (Range: 0-4) Command Mode Privileged Exec Command Usage Specifying session identifier “0” will disconnect the console connection.
4 Command Line Interface Example To show all lines, enter this command: Console#show line Console configuration: Password threshold: 3 times Interactive timeout: Disabled Login timeout: Disabled Silent time: Disabled Baudrate: auto Databits: 8 Parity: none Stopbits: 1 VTY configuration: Password threshold: 3 times Interactive timeout: 600 sec Login timeout: 300 sec Console# General Commands Table 4-6 General Commands Command Function Mode Page enable Activates privileged mode NE 4-20 disable Ret
General Commands 4 Default Setting Level 15 Command Mode Normal Exec Command Usage • “super” is the default password required to change the command mode from Normal Exec to Privileged Exec. (To set this password, see the enable password command on page 4-28.) • The “#” character is appended to the end of the prompt to indicate that the system is in privileged access mode.
4 Command Line Interface configure This command activates Global Configuration mode. You must enter this mode to modify any settings on the switch. You must also enter Global Configuration mode prior to enabling some of the other configuration modes, including Interface Configuration, Line Configuration, VLAN Database Configuration, and Multiple Spanning Tree Configuration. See “Understanding Command Modes” on page 4-6.
General Commands 4 The ! command repeats commands from the Execution command history buffer when you are in Normal Exec or Privileged Exec Mode, and commands from the Configuration command history buffer when you are in any of the configuration modes. In this example, the !2 command repeats the second command in the Execution history buffer (config). Console#!2 Console#config Console(config)# reload This command restarts the system.
4 Command Line Interface exit This command returns to the previous configuration mode or exits the configuration program. Default Setting None Command Mode Any Example This example shows how to return to the Privileged Exec mode from the Global Configuration mode, and then quit the CLI session: Console(config)#exit Console#exit Press ENTER to start session User Access Verification Username: quit This command exits the configuration program.
System Management Commands 4 System Management Commands These commands are used to control system logs, passwords, user names, browser configuration options, and display or configure a variety of other system information.
4 Command Line Interface Example Console(config)#prompt RD2 RD2(config)# hostname This command specifies or modifies the host name for this device. Use the no form to restore the default host name. Syntax hostname name no hostname name - The name of this host.
System Management Commands 4 User Access Commands The basic commands required for management access are listed in this section. This switch also includes other options for password checking via the console or a Telnet connection (page 4-11), user authentication via a remote authentication server (page 4-69), and host access authentication for specific ports (page 4-79).
4 Command Line Interface Command Usage The encrypted password is required for compatibility with legacy password settings (i.e., plain text or encrypted) when reading the configuration file during system bootup or when downloading the configuration file from a TFTP server. There is no need for you to manually configure encrypted passwords. Example This example shows how the set the access level and password for a user.
4 System Management Commands Related Commands enable (4-20) authentication enable (4-71) IP Filter Commands Table 4-11 IP Filter Commands Command Function management Configures IP addresses that are allowed management access show management Displays the switch to be monitored or configured from a browser Mode Page GC 4-29 PE 4-30 management This command specifies the client IP addresses that are allowed management access to the switch through various protocols.
4 Command Line Interface • You can delete an address range just by specifying the start address, or by specifying both the start address and end address. Example This example restricts management access to the indicated addresses. Console(config)#management all-client 192.168.1.19 Console(config)#management all-client 192.168.1.25 192.168.1.30 Console# show management This command displays the client IP addresses that are allowed management access to the switch through various protocols.
System Management Commands 4 Web Server Commands Table 4-12 Web Server Commands Command Function Mode ip http port Specifies the port to be used by the web browser interface GC Page 4-31 ip http server Allows the switch to be monitored or configured from a browser GC 4-31 ip http secure-server Enables HTTPS (HTTP/SSL) for encrypted communications GC 4-32 ip http secure-port Specifies the UDP port number for HTTPS GC 4-33 ip http port This command specifies the TCP port number used by the
4 Command Line Interface Example Console(config)#ip http server Console(config)# Related Commands ip http port (4-31) ip http secure-server This command enables the secure hypertext transfer protocol (HTTPS) over the Secure Socket Layer (SSL), providing secure access (i.e., an encrypted connection) to the switch’s web interface. Use the no form to disable this function.
System Management Commands 4 Example Console(config)#ip http secure-server Console(config)# Related Commands ip http secure-port (4-33) copy tftp https-certificate (4-64) ip http secure-port This command specifies the UDP port number used for HTTPS connection to the switch’s web interface. Use the no form to restore the default port. Syntax ip http secure-port port_number no ip http secure-port port_number – The UDP port used for HTTPS.
4 Command Line Interface Telnet Server Commands Table 4-14 Telnet Server Commands Command Function ip telnet server Allows the switch to be monitored or configured from Telnet; also GC specifies the port to be used by the Telnet interface Mode Page 4-31 ip telnet server This command allows this device to be monitored or configured from Telnet. It also specifies the TCP port number used by the Telnet interface. Use the no form without the “port” keyword to disable this function.
System Management Commands 4 This section describes the commands used to configure the SSH server. However, note that you also need to install a SSH client on the management station when using this protocol to configure the switch. Note: The switch supports both SSH Version 1.5 and 2.0 clients.
4 Command Line Interface 10.1.0.54 1024 35 15684995401867669259333946775054617325313674890836547254 15020245593199868544358361651999923329781766065830956 10825913212890233 76546801726272571413428762941301196195566782 59566410486957427888146206 51941746772984865468615717739390164779355942303577413098022737087794545 24083971752646358058176716709574804776117 3.
System Management Commands 4 ip ssh server This command enables the Secure Shell (SSH) server on this switch. Use the no form to disable this service. Syntax [no] ip ssh server Default Setting Disabled Command Mode Global Configuration Command Usage • The SSH server supports up to four client sessions. The maximum number of client sessions includes both current Telnet sessions and SSH sessions.
4 Command Line Interface Command Usage The timeout specifies the interval the switch will wait for a response from the client during the SSH negotiation phase. Once an SSH session has been established, the timeout for user input is controlled by the exec-timeout command for vty sessions.
System Management Commands 4 Default Setting 768 bits Command Mode Global Configuration Command Usage • The server key is a private key that is never shared outside the switch. • The host key is shared with the SSH client, and is fixed at 1024 bits. Example Console(config)#ip ssh server-key size 512 Console(config)# delete public-key This command deletes the specified user’s public key. Syntax delete public-key username [dsa | rsa] • username – Name of an SSH user.
4 Command Line Interface Command Usage • This command stores the host key pair in memory (i.e., RAM). Use the ip ssh save host-key command to save the host key pair to flash memory. • Some SSH client programs automatically add the public key to the known hosts file as part of the configuration process. Otherwise, you must manually create a known hosts file and place the host public key in it.
System Management Commands 4 ip ssh save host-key This command saves the host key from RAM to flash memory. Syntax ip ssh save host-key [dsa | rsa] • dsa – DSA key type. • rsa – RSA key type. Default Setting Saves both the DSA and RSA key. Command Mode Privileged Exec Example Console#ip ssh save host-key dsa Console# Related Commands ip ssh crypto host-key generate (4-39) show ip ssh This command displays the connection settings used when authenticating client access to the SSH server.
4 Command Line Interface Table 4-16 show ssh - display description Field Description Session The session number. (Range: 0-3) Version The Secure Shell version number. State The authentication negotiation state. (Values: Negotiation-Started, Authentication-Started, Session-Started) Username The user name of the client. Encryption The encryption method is automatically negotiated between the client and server. Options for SSHv1.5 include: DES, 3DES Options for SSHv2.
System Management Commands 4 • When an RSA key is displayed, the first field indicates the size of the host key (e.g., 1024), the second field is the encoded public exponent (e.g., 35), and the last string is the encoded modulus. When a DSA key is displayed, the first field indicates that the encryption method used by SSH is based on the Digital Signature Standard (DSS), and the last string is the encoded modulus.
4 Command Line Interface Default Setting None Command Mode Global Configuration Command Usage The logging process controls error messages saved to switch memory. You can use the logging history command to control the type of error messages that are stored. Example Console(config)#logging on Console(config)# Related Commands logging history (4-44) clear log (4-47) logging history This command limits syslog messages saved to switch memory based on severity.
System Management Commands 4 Default Setting • Flash: errors (level 3 - 0) • RAM: warnings (level 7 - 0) Command Mode Global Configuration Command Usage The message level specified for flash memory must be a higher priority (i.e., numerically lower) than that specified for RAM. Example Console(config)#logging history ram 0 Console(config)# logging host This command adds a syslog server host IP address that will receive logging messages. Use the no form to remove a syslog server host.
4 Command Line Interface Default Setting 23 Command Mode Global Configuration Command Usage The command specifies the facility type tag sent in syslog messages. (See RFC 3164.) This type has no effect on the kind of messages reported by the switch. However, it may be used by the syslog server to sort messages or to store messages in the corresponding database.
System Management Commands 4 clear log This command clears messages from the log buffer. Syntax clear log [flash | ram] • flash - Event history stored in flash memory (i.e., permanent memory). • ram - Event history stored in temporary RAM (i.e., memory flushed on power reset).
4 Command Line Interface Example The following example shows that system logging is enabled, the message level for flash memory is “errors” (i.e., default level 3 - 0), and the message level for RAM is “debugging” (i.e., default level 7 - 0).
System Management Commands 4 show log This command displays the log messages stored in local memory. Syntax show log {flash | ram} • flash - Event history stored in flash memory (i.e., permanent memory). • ram - Event history stored in temporary RAM (i.e., memory flushed on power reset). Default Setting None Command Mode Privileged Exec Example The following example shows the event message stored in RAM. Console#show log ram [1] 00:01:30 2001-01-01 "VLAN 1 link-up notification.
4 Command Line Interface logging sendmail host This command specifies SMTP servers that will be sent alert messages. Use the no form to remove an SMTP server. Syntax [no] logging sendmail host ip_address ip_address - IP address of an SMTP server that will be sent alert messages for event handling. Default Setting None Command Mode Global Configuration Command Usage • You can specify up to three SMTP servers for event handing. However, you must enter a separate command to specify each server.
System Management Commands 4 Command Usage The specified level indicates an event threshold. All events at this level or higher will be sent to the configured email recipients. (For example, using Level 7 will report all events from level 7 to level 0.) Example This example will send email alerts for system errors from level 3 through 0. Console(config)#logging sendmail level 3 Console(config)# logging sendmail source-email This command sets the email address used for the “From” field in alert messages.
4 Command Line Interface Command Usage You can specify up to five recipients for alert messages. However, you must enter a separate command to specify each recipient. Example Console(config)#logging sendmail destination-email ted@this-company.com Console(config)# logging sendmail This command enables SMTP event handling. Use the no form to disable this function.
System Management Commands 4 Time Commands The system clock can be dynamically set by polling a set of specified time servers (NTP or SNTP). Maintaining an accurate time on the switch enables the system log to record meaningful dates and times for event entries. If the clock is not set, the switch will only record the time from the factory default set at the last bootup.
4 Command Line Interface Example Console(config)#sntp server 10.1.0.19 Console(config)#sntp poll 60 Console(config)#sntp client Console(config)#end Console#show sntp Current time: Dec 23 02:52:44 2002 Poll interval: 60 Current mode: unicast SNTP status : Enabled SNTP server 137.92.140.80 0.0.0.0 0.0.0.0 Current server: 137.92.140.
System Management Commands 4 sntp poll This command sets the interval between sending time requests when the switch is set to SNTP client mode. Use the no form to restore to the default. Syntax sntp poll seconds no sntp poll seconds - Interval between time requests.
4 Command Line Interface clock timezone This command sets the time zone for the switch’s internal clock. Syntax clock timezone name hour hours minute minutes {before-utc | after-utc} • • • • • name - Name of timezone, usually an acronym. (Range: 1-29 characters) hours - Number of hours before/after UTC. (Range: 0-13 hours) minutes - Number of minutes before/after UTC. (Range: 0-59 minutes) before-utc - Sets the local time zone before (east) of UTC.
System Management Commands 4 Default Setting None Command Mode Privileged Exec Example This example shows how to set the system clock to 15:12:34, February 1st, 2002. Console#calendar set 15:12:34 1 February 2002 Console# show calendar This command displays the system clock.
4 Command Line Interface Command Usage • Use this command in conjunction with the show running-config command to compare the information in running memory to the information stored in non-volatile memory. • This command displays settings for key command modes. Each mode group is separated by “!” symbols, and includes the configuration mode command, and corresponding commands.
System Management Commands 4 interface VLAN 1 ip address DHCP ! no map IP precedence no map IP DSCP ! line console ! line VTY ! end ! Console# Related Commands show running-config (4-59) show running-config This command displays the configuration information currently in use. Default Setting None Command Mode Privileged Exec Command Usage • Use this command in conjunction with the show startup-config command to compare the information in running memory to the information stored in non-volatile memory.
4 Command Line Interface Example Console#show running-config building running-config, please wait..... !00 !01_00-30-f1-fd-e2-40_01 ! phymap 00-30-f1-fd-e2-40 ! SNTP server 0.0.0.0 0.0.0.0 0.0.0.
System Management Commands 4 Command Usage • For a description of the items shown by this command, refer to “Displaying System Information” on page 3-12. • The POST results should all display “PASS.” If any POST test indicates “FAIL,” contact your distributor for assistance. Example Console#show system System Description: 24FE+4GE L2/3/4 Standalone Switch System OID String: 1.3.6.1.4.1.259.6.10.75 System information System Up Time: 0 days, 1 hours, 16 minutes, and 44.
4 Command Line Interface Example Console#show users Username accounts: Username Privilege Public-Key -------- --------- ---------admin 15 None guest 0 None steve 15 RSA Online users: Line Username Idle time (h:m:s) Remote IP addr. ----------- -------- ----------------- --------------0 console admin 0:14:14 * 1 VTY 0 admin 0:00:00 192.168.1.19 2 SSH 1 steve 0:00:06 192.168.1.19 Web online users: Line Remote IP addr Username Idle time (h:m:s). ----------- -------------- -------- -----------------1 HTTP 192.
System Management Commands 4 Frame Size Commands Table 4-24 Frame Size Commands Command Function Mode jumbo frame Enables support for jumbo frames GC Page 4-63 jumbo frame This command enables support for jumbo frames. Use the no form to disable it. Syntax [no] jumbo frame Default Setting Disabled Command Mode Global Configuration Command Usage • This switch provides more efficient throughput for large sequential data transfers by supporting jumbo frames up to 9216 bytes.
4 Command Line Interface Flash/File Commands These commands are used to manage the system code or configuration files.
Flash/File Commands 4 Command Usage • The system prompts for data required to complete the copy command. • The destination file name should not contain slashes (\ or /), the leading letter of the file name should not be a period (.), and the maximum length for file names on the TFTP server is 127 characters or 31 characters for files on the switch. (Valid characters: A-Z, a-z, 0-9, “.”, “-”, “_”) • Due to the size limit of the flash memory, the switch supports only two operation code files.
4 Command Line Interface The following example shows how to download a configuration file: Console#copy tftp startup-config TFTP server ip address: 10.1.0.99 Source configuration file name: startup.01 Startup configuration file name [startup]: Write to FLASH Programming. \Write to FLASH finish. Success. Console# This example shows how to copy a secure-site certificate from an TFTP server.
Flash/File Commands 4 Command Usage • If the file type is used for system startup, then this file cannot be deleted. • “Factory_Default_Config.cfg” cannot be deleted. Example This example shows how to delete the test2.cfg configuration file from flash memory. Console#delete test2.cfg Console# Related Commands dir (4-67) delete public-key (4-39) dir This command displays a list of files in flash memory.
4 Command Line Interface Example The following example shows how to display all file information: Console#dir File name File type Startup Size (byte) -------------------------------------------------- ------- ----------Unit1: D1016 Boot-Rom Image Y 1129180 V31018 Operation Code Y 4095300 Factory_Default_Config.cfg Config File N 455 startup1.
Authentication Commands 4 Command Mode Global Configuration Command Usage • A colon (:) is required after the specified file type. • If the file contains an error, it cannot be set as the default file. Example Console(config)#boot system config: startup Console(config)# Related Commands dir (4-67) whichboot (4-68) Authentication Commands You can configure this switch to authenticate users logging into the system for management access using local or remote authentication methods.
4 Command Line Interface Authentication Sequence Table 4-28 Authentication Sequence Commands Command Function Mode authentication login Defines logon authentication method and precedence GC Page 4-70 authentication enable Defines the authentication method and precedence for command mode change GC 4-71 authentication login This command defines the login authentication method and precedence. Use the no form to restore the default.
Authentication Commands 4 authentication enable This command defines the authentication method and precedence to use when changing from Exec command mode to Privileged Exec command mode with the enable command (see page 4-20). Use the no form to restore the default. Syntax authentication enable {[local] [radius] [tacacs]} no authentication enable • local - Use local password only. • radius - Use RADIUS server password only. • tacacs - Use TACACS server password.
4 Command Line Interface RADIUS Client Remote Authentication Dial-in User Service (RADIUS) is a logon authentication protocol that uses software running on a central server to control access to RADIUS-aware devices on the network. An authentication server contains a database of multiple user name/password pairs with associated privilege levels for each user or group that require management access to a switch.
Authentication Commands 4 Example Console(config)#radius-server 1 host 192.168.1.20 port 181 timeout 10 retransmit 5 key green Console(config)# radius-server port This command sets the RADIUS server network port. Use the no form to restore the default. Syntax radius-server port port_number no radius-server port port_number - RADIUS server UDP port used for authentication messages.
4 Command Line Interface radius-server retransmit This command sets the number of retries. Use the no form to restore the default. Syntax radius-server retransmit number_of_retries no radius-server retransmit number_of_retries - Number of times the switch will try to authenticate logon access via the RADIUS server.
Authentication Commands 4 Example Console#show radius-server Remote RADIUS server configuration: Global settings: Communication key with RADIUS server: ***** Server port number: 1812 Retransmit times: 2 Request timeout: 5 Server 1: Server IP address: 192.168.1.
4 Command Line Interface Example Console(config)#tacacs-server host 192.168.1.25 Console(config)# tacacs-server port This command specifies the TACACS+ server network port. Use the no form to restore the default. Syntax tacacs-server port port_number no tacacs-server port port_number - TACACS+ server TCP port used for authentication messages.
Authentication Commands 4 show tacacs-server This command displays the current settings for the TACACS+ server. Default Setting None Command Mode Privileged Exec Example Console#show tacacs-server Remote TACACS server configuration: Server IP address: 10.11.12.13 Communication key with TACACS server: ***** Server port number: 49 Console# Port Security Commands These commands can be used to enable port security on a port.
4 Command Line Interface port security This command enables or configures port security. Use the no form without any keywords to disable port security. Use the no form with the appropriate keyword to restore the default settings for a response to security violation or for the maximum number of allowed addresses.
Authentication Commands 4 Example The following example enables port security for port 5, and sets the response to a security violation to issue a trap message: Console(config)#interface ethernet 1/5 Console(config-if)#port security action trap Related Commands shutdown (4-148) mac-address-table static (4-167) show mac-address-table (4-168) 802.1X Port Authentication The switch supports IEEE 802.
4 Command Line Interface dot1x system-auth-control This command enables IEEE 802.1X port authentication globally on the switch. Use the no form to restore the default. Syntax [no] dot1x system-auth-control Default Setting Disabled Command Mode Global Configuration Example Console(config)#dot1x system-auth-control Console(config)# dot1x default This command sets all configurable dot1x global and port settings to their default values.
Authentication Commands 4 dot1x port-control This command sets the dot1x mode on a port interface. Use the no form to restore the default. Syntax dot1x port-control {auto | force-authorized | force-unauthorized} no dot1x port-control • auto – Requires a dot1x-aware connected client to be authorized by the RADIUS server. Clients that are not dot1x-aware will be denied access. • force-authorized – Configures the port to grant access to all clients, either dot1x-aware or otherwise.
4 Command Line Interface Command Usage • The “max-count” parameter specified by this command is only effective if the dot1x mode is set to “auto” by the dot1x port-control command (page 4-105). • In “multi-host” mode, only one host connected to a port needs to pass authentication for all other hosts to be granted network access. Similarly, a port can become unauthorized for all hosts if one attached host fails re-authentication or sends an EAPOL logoff message.
Authentication Commands 4 dot1x timeout quiet-period This command sets the time that a switch port waits after the Max Request Count has been exceeded before attempting to acquire a new client. Use the no form to reset the default. Syntax dot1x timeout quiet-period seconds no dot1x timeout quiet-period seconds - The number of seconds.
4 Command Line Interface dot1x timeout tx-period This command sets the time that an interface on the switch waits during an authentication session before re-transmitting an EAP packet. Use the no form to reset to the default value. Syntax dot1x timeout tx-period seconds no dot1x timeout tx-period seconds - The number of seconds.
Authentication Commands - Mode - Authorized 4 – Dot1x port control mode (page 4-81). – Authorization status (yes or n/a - not authorized). • 802.1X Port Details – Displays the port access control parameters for each interface, including the following items: - reauth-enabled – Periodic re-authentication (page 4-82). - reauth-period – Time after which a connected client must be re-authenticated (page 4-83).
4 Command Line Interface • Reauthentication State Machine - State – Current state (including initialize, reauthenticate). Example Console#show dot1x Global 802.1X Parameters system-auth-control: enable 802.1X Port Summary Port Name 1/1 1/2 . . . 1/25 1/26 Status disabled disabled Operation Mode Single-Host Single-Host Mode ForceAuthorized ForceAuthorized Authorized n/a n/a disabled enabled Single-Host Single-Host ForceAuthorized Auto yes yes 802.1X Port Details 802.1X is enabled on port 1/1 . . .
Access Control List Commands 4 Access Control List Commands Access Control Lists (ACL) provide packet filtering for IP frames (based on address, protocol, Layer 4 protocol port number or TCP control code) or any frames (based on MAC address or Ethernet type). To filter packets, first create an access list, add the required rules, specify a mask to modify the precedence in which the rules are checked, and then bind the list to a specific port.
4 Command Line Interface The order in which active ACLs are checked is as follows: 1. User-defined rules in the Egress MAC ACL for egress ports. 2. User-defined rules in the Egress IP ACL for egress ports. 3. User-defined rules in the Ingress MAC ACL for ingress ports. 4. User-defined rules in the Ingress IP ACL for ingress ports. 5. Explicit default rule (permit any any) in the ingress IP ACL for ingress ports. 6. Explicit default rule (permit any any) in the ingress MAC ACL for ingress ports. 7.
Access Control List Commands 4 access-list ip This command adds an IP access list and enters configuration mode for standard or extended IP ACLs. Use the no form to remove the specified ACL. Syntax [no] access-list ip {standard | extended} acl_name • standard – Specifies an ACL that filters packets based on the source IP address. • extended – Specifies an ACL that filters packets based on the source or destination IP address, and other more specific criteria. • acl_name – Name of the ACL.
4 Command Line Interface Default Setting None Command Mode Standard ACL Command Usage • New rules are appended to the end of the list. • Address bitmasks are similar to a subnet mask, containing four integers from 0 to 255, each separated by a period. The binary mask uses 1 bits to indicate “match” and 0 bits to indicate “ignore.
Access Control List Commands 4 • • • • • • precedence – IP precedence level. (Range: 0-7) tos – Type of Service level. (Range: 0-15) dscp – DSCP priority level. (Range: 0-63) sport – Protocol37 source port number. (Range: 0-65535) dport – Protocol37 destination port number. (Range: 0-65535) port-bitmask – Decimal number representing the port bits to match. (Range: 0-65535) • control-flags – Decimal number (representing a bit string) that specifies flag bits in byte 14 of the TCP header.
4 Command Line Interface Example This example accepts any incoming packets if the source address is within subnet 10.7.1.x. For example, if the rule is matched; i.e., the rule (10.7.1.0 & 255.255.255.0) equals the masked address (10.7.1.2 & 255.255.255.0), the packet passes through. Console(config-ext-acl)#permit 10.7.1.1 255.255.255.0 any Console(config-ext-acl)# This allows TCP packets from class C addresses 192.168.1.0 to any destination address when set for destination TCP port 80 (i.e., HTTP).
Access Control List Commands 4 access-list ip mask-precedence This command changes to the IP Mask mode used to configure access control masks. Use the no form to delete the mask table. Syntax [no] access-list ip mask-precedence {in | out} • in – Ingress mask for ingress ACLs. • out – Egress mask for egress ACLs. Default Setting Default system mask: Filter inbound packets according to specified IP ACLs.
4 Command Line Interface • • • • • • • destination-bitmask – Destination address of rule must match this bitmask. precedence – Check the IP precedence field. tos – Check the TOS field. dscp – Check the DSCP field. source-port – Check the protocol source port field. destination-port – Check the protocol destination port field. port-bitmask – Protocol port of rule must match this bitmask. (Range: 0-65535) • control-flag – Check the field for control flags.
Access Control List Commands 4 This shows that the entries in the mask override the precedence in which the rules are entered into the ACL. In the following example, packets with the source address 10.1.1.1 are dropped because the “deny 10.1.1.1 255.255.255.255” rule has the higher precedence according the “mask host any” entry. Console(config)#access-list ip standard A2 Console(config-std-acl)#permit 10.1.1.0 255.255.255.0 Console(config-std-acl)#deny 10.1.1.1 255.255.255.
4 Command Line Interface This shows how to create an extended ACL with an egress mask to drop packets leaving network 171.69.198.0 when the Layer 4 source port is 23. Console(config)#access-list ip extended A3 Console(config-ext-acl)#deny host 171.69.198.5 any Console(config-ext-acl)#deny 171.69.198.0 255.255.255.0 any source-port 23 Console(config-ext-acl)#end Console#show access-list IP extended access-list A3: deny host 171.69.198.5 any deny 171.69.198.0 255.255.255.
Access Control List Commands 4 This is a more comprehensive example. It denies any TCP packets in which the SYN bit is ON, and permits all other packets. It then sets the ingress mask to check the deny rule first, and finally binds port 1 to this ACL. Note that once the ACL is bound to an interface (i.e., the ACL is active), the order in which the rules are displayed is determined by the associated mask.
4 Command Line Interface Related Commands mask (IP ACL) (4-93) ip access-group This command binds a port to an IP ACL. Use the no form to remove the port. Syntax [no] ip access-group acl_name {in | out} • acl_name – Name of the ACL. (Maximum length: 16 characters) • in – Indicates that this list applies to ingress packets. • out – Indicates that this list applies to egress packets. Default Setting None Command Mode Interface Configuration (Ethernet) Command Usage • A port can only be bound to one ACL.
Access Control List Commands 4 MAC ACLs Table 4-35 MAC ACL Commands Command Function Mode access-list mac Creates a MAC ACL and enters configuration mode GC Page permit, deny Filters packets matching a specified source and destination address, packet format, and Ethernet type MAC-ACL 4-100 show mac access-list Displays the rules for configured MAC ACLs PE 4-101 access-list mac mask-precedence Changes to the mode for configuring access control masks GC 4-102 mask Sets a precedence mask f
4 Command Line Interface Related Commands permit, deny (4-100) mac access-group (4-105) show mac access-list (4-101) permit, deny (MAC ACL) This command adds a rule to a MAC ACL. The rule filters packets matching a specified MAC source or destination address (i.e., physical layer address), or Ethernet protocol type. Use the no form to remove a rule.
Access Control List Commands 4 • vid-bitmask38 – VLAN bitmask. (Range: 1-4094) • protocol – A specific Ethernet protocol number. (Range: 600-fff hex.) • protocol-bitmask38 – Protocol bitmask. (Range: 600-fff hex.) Default Setting None Command Mode MAC ACL Command Usage • New rules are added to the end of the list. • The ethertype option can only be used to filter Ethernet II formatted packets. • A detailed listing of Ethernet protocol types can be found in RFC 1060.
4 Command Line Interface access-list mac mask-precedence This command changes to MAC Mask mode used to configure access control masks. Use the no form to delete the mask table. Syntax [no] access-list ip mask-precedence {in | out} • in – Ingress mask for ingress ACLs. • out – Egress mask for egress ACLs. Default Setting Default system mask: Filter inbound packets according to specified MAC ACLs.
Access Control List Commands 4 • vid-bitmask – VLAN ID of rule must match this bitmask. • ethertype – Check the Ethernet type field. • ethertype-bitmask – Ethernet type of rule must match this bitmask. Default Setting None Command Mode MAC Mask Command Usage • Up to seven masks can be assigned to an ingress or egress ACL. • Packets crossing a port are checked against all the rules in the ACL until a match is found.
4 Command Line Interface This example creates an Egress MAC ACL. Console(config)#access-list mac M5 Console(config-mac-acl)#deny tagged-802.3 host 00-11-11-11-11-11 any Console(config-mac-acl)#deny tagged-eth2 00-11-11-11-11-11 ff-ff-ff-ff-ff-ff any vid 3 ethertype 0806 Console(config-mac-acl)#end Console#show access-list MAC access-list M5: deny tagged-802.
Access Control List Commands 4 mac access-group This command binds a port to a MAC ACL. Use the no form to remove the port. Syntax mac access-group acl_name {in | out} • acl_name – Name of the ACL. (Maximum length: 16 characters) • in – Indicates that this list applies to ingress packets. • out – Indicates that this list applies to egress packets. Default Setting None Command Mode Interface Configuration (Ethernet) Command Usage • A port can only be bound to one ACL.
4 Command Line Interface ACL Information Table 4-36 ACL Information Commands Command Function Mode Page show access-list Show all ACLs and associated rules PE 4-106 show access-group Shows the ACLs assigned to each port PE 4-106 show access-list This command shows all ACLs and associated rules, as well as all the user-defined masks. Command Mode Privileged Exec Command Usage Once the ACL is bound to an interface (i.e.
SNMP Commands 4 SNMP Commands Controls access to this switch from management stations using the Simple Network Management Protocol (SNMP), as well as the error types sent to trap managers. SNMP Version 3 also provides security features that cover message integrity, authentication, and encryption; as well as controlling user access to specific areas of the MIB tree.
4 Command Line Interface Example Console(config)#snmp-server Console(config)# show snmp This command can be used to check the status of SNMP communications. Default Setting None Command Mode Normal Exec, Privileged Exec Command Usage This command provides information on the community access strings, counter information for SNMP input and output protocol data units, and whether or not SNMP logging has been enabled with the snmp-server enable traps command.
SNMP Commands 4 snmp-server community This command defines the SNMP v1 and v2c community access string. Use the no form to remove the specified community string. Syntax snmp-server community string [ro|rw] no snmp-server community string • string - Community string that acts like a password and permits access to the SNMP protocol. (Maximum length: 32 characters, case sensitive; Maximum number of strings: 5) • ro - Specifies read-only access.
4 Command Line Interface Related Commands snmp-server location (4-110) snmp-server location This command sets the system location string. Use the no form to remove the location string. Syntax snmp-server location text no snmp-server location text - String that describes the system location.
SNMP Commands 4 to using the snmp-server host command. (Maximum length: 32 characters) • version - Specifies whether to send notifications as SNMP Version 1, 2c or 3 traps. (Range: 1, 2c, 3; Default: 1) - auth | noauth | priv - This group uses SNMPv3 with authentication, no authentication, or with authentication and privacy. See “Simple Network Management Protocol” on page 3-37 for further information about these authentication and encryption options. • port - Host UDP port to use.
4 Command Line Interface To send an inform to a SNMPv3 host, complete these steps: 1. Enable the SNMP agent (page 4-107). 2. Allow the switch to send SNMP traps; i.e., notifications (page 4-112). 3. Specify the target host that will receive inform messages with the snmp-server host command as described in this section. 4. Create a view with the required notification messages (page 4-115). 5. Create a group that includes the required notify view (page 4-116). 6.
SNMP Commands 4 SNMP notifications, you must enter at least one snmp-server enable traps command. If you enter the command with no keywords, both authentication and link-up-down notifications are enabled. If you enter the command with a keyword, only the notification type related to that keyword is enabled. • The snmp-server enable traps command is used in conjunction with the snmp-server host command. Use the snmp-server host command to specify which host or hosts receive SNMP notifications.
4 Command Line Interface • A remote engine ID is required when using SNMPv3 informs. (See snmp-server host on page 4-110.) The remote engine ID is used to compute the security digest for authenticating and encrypting packets sent to a user on the remote host. SNMP passwords are localized using the engine ID of the authoritative agent. For informs, the authoritative SNMP agent is the remote agent.
SNMP Commands 4 snmp-server view This command adds an SNMP view which controls user access to the MIB. Use the no form to remove an SNMP view. Syntax snmp-server view view-name oid-tree {included | excluded} no snmp-server view view-name • view-name - Name of an SNMP view. (Range: 1-64 characters) • oid-tree - Object identifier of a branch within the MIB tree. Wild cards can be used to mask a specific portion of the OID string. (Refer to the examples.) • included - Defines an included view.
4 Command Line Interface show snmp view This command shows information on the SNMP views. Command Mode Privileged Exec Example Console#show snmp view View Name: mib-2 Subtree OID: 1.2.2.3.6.2.1 View Type: included Storage Type: permanent Row Status: active View Name: defaultview Subtree OID: 1 View Type: included Storage Type: volatile Row Status: active Console# Table 4-39 show snmp view - display description Field Description View Name Name of an SNMP view. Subtree OID A branch in the MIB tree.
SNMP Commands 4 Default Setting • • • • Default groups: public39 (read only), private40 (read/write) readview - Every object belonging to the Internet OID space (1.3.6.1). writeview - Nothing is defined. notifyview - Nothing is defined. Command Mode Global Configuration Command Usage • A group sets the access policy for the assigned users. • When authentication is selected, the MD5 or SHA algorithm is used as specified in the snmp-server user command.
4 Command Line Interface Group Name: public Security Model: v2c Read View: defaultview Write View: none Notify View: none Storage Type: volatile Row Status: active Group Name: private Security Model: v1 Read View: defaultview Write View: defaultview Notify View: none Storage Type: volatile Row Status: active Group Name: private Security Model: v2c Read View: defaultview Write View: defaultview Notify View: none Storage Type: volatile Row Status: active Console# Table 4-40 show snmp group - display descri
SNMP Commands 4 • • • • • • ip-address - The Internet address of the remote device. v1 | v2c | v3 - Use SNMP version 1, 2c or 3. encrypted - Accepts the password as encrypted input. auth - Uses SNMPv3 with authentication. md5 | sha - Uses MD5 or SHA authentication. auth-password - Authentication password. Enter as plain text if the encrypted option is not used. Otherwise, enter an encrypted password. (A minimum of eight characters is required.
4 Command Line Interface show snmp user This command shows information on SNMP users.
DHCP Commands 4 DHCP Commands These commands are used to configure Dynamic Host Configuration Protocol (DHCP) client, relay, and server functions. You can configure any VLAN interface to be automatically assigned an IP address via DHCP. This switch can be configured to relay DHCP client configuration requests to a DHCP server on another network, or you can configure this switch to provide DHCP service directly to any client.
4 Command Line Interface Related Commands ip dhcp restart client (4-122) ip dhcp restart client This command submits a BOOTP or DHCP client request. Default Setting None Command Mode Privileged Exec Command Usage • This command issues a BOOTP or DHCP client request for any IP interface that has been set to BOOTP or DHCP mode via the ip address command. • DHCP requires the server to reassign the client’s last address if available.
DHCP Commands 4 DHCP Relay Table 4-44 DHCP Relay Commands Command Function Mode Page ip dhcp restart relay Enables DHCP relay agent IC 4-123 ip dhcp relay server Specifies DHCP server addresses for relay IC 4-124 ip dhcp restart relay This command enables DHCP relay for the specified VLAN. Use the no form to disable it.
4 Command Line Interface ip dhcp relay server This command specifies the addresses of DHCP servers to be used by the switch’s DHCP relay agent. Use the no form to clear all addresses. Syntax ip dhcp relay server address1 [address2 [address3 ...]] no ip dhcp relay server address - IP address of DHCP server. (Range: 1-3 addresses) Default Setting None Command Mode Interface Configuration (VLAN) Usage Guidelines • You must specify the IP address for at least one DHCP server.
DHCP Commands 4 Table 4-45 DHCP Server Commands (Continued) Command Function Mode Page netbios-node-type Configures NetBIOS node type for Microsoft DHCP clients DC 4-131 lease Sets the duration an IP address is assigned to a DHCP client DC 4-131 host* Specifies the IP address and network mask to manually bind to a DC DHCP client 4-132 client-identifier* Specifies a client identifier for a DHCP client DC 4-133 hardware-address* Specifies the hardware address of a DHCP client DC 4-134
4 Command Line Interface Default Setting All IP pool addresses may be assigned. Command Mode Global Configuration Example Console(config)#ip dhcp excluded-address 10.1.0.19 Console(config)# ip dhcp pool This command configures a DHCP address pool and enter DHCP Pool Configuration mode. Use the no form to remove the address pool. Syntax [no] ip dhcp pool name name - A string or integer. (Range: 1-8 characters) Default Setting DHCP address pools are not configured.
DHCP Commands 4 network This command configures the subnet number and mask for a DHCP address pool. Use the no form to remove the subnet number and mask. Syntax network network-number [mask] no network • network-number - The IP address of the DHCP address pool. • mask - The bit combination that identifies the network (or subnet) and the host portion of the DHCP address pool.
4 Command Line Interface Command Mode DHCP Pool Configuration Usage Guidelines The IP address of the router should be on the same subnet as the client. You can specify up to two routers. Routers are listed in order of preference (starting with address1 as the most preferred router). Example Console(config-dhcp)#default-router 10.1.0.54 10.1.0.64 Console(config-dhcp)# domain-name This command specifies the domain name for a DHCP client. Use the no form to remove the domain name.
DHCP Commands 4 Usage Guidelines • If DNS IP servers are not configured for a DHCP client, the client cannot correlate host names to IP addresses. • Servers are listed in order of preference (starting with address1 as the most preferred server). Example Console(config-dhcp)#dns-server 10.1.1.253 192.168.3.19 Console(config-dhcp)# next-server This command configures the next server in the boot process of a DHCP client. Use the no form to remove the boot server list.
4 Command Line Interface Example Console(config-dhcp)#bootfile wme.bat Console(config-dhcp)# Related Commands next-server (4-129) netbios-name-server This command configures NetBIOS Windows Internet Naming Service (WINS) name servers that are available to Microsoft DHCP clients. Use the no form to remove the NetBIOS name server list. Syntax netbios-name-server address1 [address2] no netbios-name-server • address1 - Specifies IP address of primary NetBIOS WINS name server.
DHCP Commands 4 netbios-node-type This command configures the NetBIOS node type for Microsoft DHCP clients. Use the no form to remove the NetBIOS node type.
4 Command Line Interface Command Modes DHCP Pool Configuration Example The following example leases an address to clients using this pool for 7 days. Console(config-dhcp)#lease 7 Console(config-dhcp)# host Use this command to specify the IP address and network mask to manually bind to a DHCP client. Use the no form to remove the IP address for the client. Syntax host address [mask] no host • address - Specifies the IP address of a client. • mask - Specifies the network mask of the client.
DHCP Commands 4 Example Console(config-dhcp)#host 10.1.0.21 255.255.255.0 Console(config-dhcp)# Related Commands client-identifier (4-133) hardware-address (4-134) client-identifier This command specifies the client identifier of a DHCP client. Use the no form to remove the client identifier. Syntax client-identifier {text text | hex hex} no client-identifier • text - A text string. (Range: 1-15 characters) • hex - The hexadecimal value.
4 Command Line Interface hardware-address This command specifies the hardware address of a DHCP client. This command is valid for manual bindings only. Use the no form to remove the hardware address. Syntax hardware-address hardware-address type no hardware-address • hardware-address - Specifies the MAC address of the client device. • type - Indicates the following protocol used on the client device: - ethernet - ieee802 - fddi Default Setting If no type is specified, the default protocol is Ethernet.
DHCP Commands 4 Usage Guidelines • An address specifies the client’s IP address. If an asterisk (*) is used as the address parameter, the DHCP server clears all automatic bindings. • Use the no host command to delete a manual binding. • This command is normally used after modifying the address pool, or after moving DHCP service to another device. Example.
4 Command Line Interface DNS Commands These commands are used to configure Domain Naming System (DNS) services. You can manually configure entries in the DNS domain name to IP address mapping table, configure default domain names, or specify one or more name servers to use for domain name to address translation. Note that domain name services will not be enabled until at least one name server is specified with the ip name-server command and domain lookup is enabled with the ip domain-lookup command.
DNS Commands 4 Command Usage Servers or other network devices may support one or more connections via multiple IP addresses. If more than one IP address is associated with a host name using this command, a DNS client can try each address in succession, until it establishes a connection with the target device. Example This example maps two address to a host name. Console(config)#ip host rd5 192.168.1.55 10.1.0.55 Console(config)#end Console#show hosts Hostname rd5 Inet address 10.1.0.55 192.168.1.
4 Command Line Interface Default Setting None Command Mode Global Configuration Example Console(config)#ip domain-name sample.com Console(config)#end Console#show dns Domain Lookup Status: DNS disabled Default Domain Name: .sample.com Domain Name List: Name Server List: Console# Related Commands ip domain-list (4-138) ip name-server (4-139) ip domain-lookup (4-140) ip domain-list This command defines a list of domain names that can be appended to incomplete host names (i.e.
DNS Commands 4 Example This example adds two domain names to the current list and then displays the list. Console(config)#ip domain-list sample.com.jp Console(config)#ip domain-list sample.com.uk Console(config)#end Console#show dns Domain Lookup Status: DNS disabled Default Domain Name: .sample.com Domain Name List: .sample.com.jp .sample.com.
4 Command Line Interface Example This example adds two domain-name servers to the list and then displays the list. Console(config)#ip domain-server 192.168.1.55 10.1.0.55 Console(config)#end Console#show dns Domain Lookup Status: DNS disabled Default Domain Name: .sample.com Domain Name List: .sample.com.jp .sample.com.uk Name Server List: 192.168.1.55 10.1.0.
DNS Commands 4 Related Commands ip domain-name (4-137) ip name-server (4-139) show hosts This command displays the static host name-to-address mapping table. Command Mode Privileged Exec Example Note that a host name will be displayed as an alias if it is mapped to the same address(es) as a previously configured entry. Console#show hosts Hostname rd5 Inet address 10.1.0.55 192.168.1.55 Alias 1.rd6 Console# show dns This command displays the configuration of the DNS server.
4 Command Line Interface show dns cache This command displays entries in the DNS cache. Command Mode Privileged Exec Example Console#show dns cache NO FLAG TYPE 2 4 CNAME 3 4 CNAME 4 4 CNAME 5 4 CNAME 6 4 CNAME 7 4 CNAME 8 4 ALIAS Console# IP 66.218.71.84 66.218.71.83 66.218.71.81 66.218.71.80 66.218.71.89 66.218.71.86 POINTER TO:7 TTL 298 298 298 298 298 298 298 DOMAIN www.yahoo.akadns.net www.yahoo.akadns.net www.yahoo.akadns.net www.yahoo.akadns.net www.yahoo.akadns.net www.yahoo.akadns.net www.
4 Interface Commands Interface Commands These commands are used to display or set communication parameters for an Ethernet port, aggregated link, or VLAN.
4 Command Line Interface Command Mode Global Configuration Example To specify port 4, enter the following command: Console(config)#interface ethernet 1/4 Console(config-if)# description This command adds a description to an interface. Use the no form to remove the description. Syntax description string no description string - Comment or a description to help you remember what is attached to this interface.
Interface Commands 4 Default Setting • Auto-negotiation is enabled by default.
4 Command Line Interface • If autonegotiation is disabled, auto-MDI/MDI-X pin signal configuration will also be disabled for the RJ-45 ports. Example The following example configures port 11 to use autonegotiation. Console(config)#interface ethernet 1/11 Console(config-if)#negotiation Console(config-if)# Related Commands capabilities (4-146) speed-duplex (4-144) capabilities This command advertises the port capabilities of a given interface during autonegotiation.
Interface Commands 4 Example The following example configures Ethernet port 5 capabilities to 100half, 100full and flow control. Console(config)#interface ethernet 1/5 Console(config-if)#capabilities 100half Console(config-if)#capabilities 100full Console(config-if)#capabilities flowcontrol Console(config-if)# Related Commands negotiation (4-145) speed-duplex (4-144) flowcontrol (4-147) flowcontrol This command enables flow control. Use the no form to disable flow control.
4 Command Line Interface Related Commands negotiation (4-145) capabilities (flowcontrol, symmetric) (4-146) shutdown This command disables an interface. To restart a disabled interface, use the no form. Syntax [no] shutdown Default Setting All interfaces are enabled. Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage This command allows you to disable a port due to abnormal behavior (e.g., excessive collisions), and then reenable it after the problem has been resolved.
Interface Commands 4 Command Usage • When broadcast traffic exceeds the specified threshold, packets above that threshold are dropped. • Broadcast control does not effect IP multicast traffic. • The resolution is 1 packet per second (pps); i.e., any setting between 500-262143 is acceptable.
4 Command Line Interface show interfaces status This command displays the status for an interface. Syntax show interfaces status [interface] interface • ethernet unit/port - unit - Stack unit43. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) • vlan vlan-id (Range: 1-4094) Default Setting Shows the status for all interfaces. Command Mode Normal Exec, Privileged Exec Command Usage If no interface is specified, information on all interfaces is displayed.
Interface Commands 4 show interfaces counters This command displays interface statistics. Syntax show interfaces counters [interface] interface • ethernet unit/port - unit - Stack unit44. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting Shows the counters for all interfaces. Command Mode Normal Exec, Privileged Exec Command Usage If no interface is specified, information on all interfaces is displayed.
4 Command Line Interface show interfaces switchport This command displays the administrative and operational status of the specified interfaces. Syntax show interfaces switchport [interface] interface • ethernet unit/port - unit - Stack unit45. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting Shows all interfaces. Command Mode Normal Exec, Privileged Exec Command Usage If no interface is specified, information on all interfaces is displayed.
4 Interface Commands Table 4-49 show interfaces switchport - display description Field Description Broadcast threshold Shows if broadcast storm suppression is enabled or disabled; if enabled it also shows the threshold level (page 4-148). LACP status Shows if Link Aggregation Control Protocol has been enabled or disabled (page 4-159). Ingress/Egress rate limit Shows if rate limiting is enabled, and the current rate limit (page 4-156).
4 Command Line Interface Mirror Port Commands This section describes how to mirror traffic from a source port to a target port. Table 4-50 Mirror Port Commands Command Function Mode Page port monitor Configures a mirror session IC 4-154 show port monitor Shows the configuration for a mirror port PE 4-155 port monitor This command configures a mirror session. Use the no form to clear a mirror session.
Mirror Port Commands 4 Example The following example configures the switch to mirror all packets from port 6 to 11: Console(config)#interface ethernet 1/11 Console(config-if)#port monitor ethernet 1/6 both Console(config-if)# show port monitor This command displays mirror information. Syntax show port monitor [interface] interface - ethernet unit/port (source port) • unit - Stack unit47. (Range: 1-1) • port - Port number. (Range: 1-28) Default Setting Shows all sessions.
4 Command Line Interface Rate Limit Commands This function allows the network manager to control the maximum rate for traffic transmitted or received on an interface. Rate limiting is configured on interfaces at the edge of a network to limit traffic into or out of the network. Traffic that falls within the rate limit is transmitted, while packets that exceed the acceptable amount of traffic are dropped. Rate limiting can be applied to individual ports or trunks.
Link Aggregation Commands 4 Link Aggregation Commands Ports can be statically grouped into an aggregate link (i.e., trunk) to increase the bandwidth of a network connection or to ensure fault recovery. Or you can use the Link Aggregation Control Protocol (LACP) to automatically negotiate a trunk link between this switch and another network device. For static trunks, the switches have to comply with the Cisco EtherChannel standard. For dynamic trunks, the switches have to comply with LACP.
4 Command Line Interface Dynamically Creating a Port Channel – Ports assigned to a common port channel must meet the following criteria: • Ports must have the same LACP system priority. • Ports must have the same port admin key (Ethernet Interface). • If the port channel admin key (lacp admin key - Port Channel) is not set when a channel group is formed (i.e.
Link Aggregation Commands 4 lacp This command enables 802.3ad Link Aggregation Control Protocol (LACP) for the current interface. Use the no form to disable it. Syntax [no] lacp Default Setting Disabled Command Mode Interface Configuration (Ethernet) Command Usage • The ports on both ends of an LACP trunk must be configured for full duplex, either by forced mode or auto-negotiation. • A trunk formed with another switch using LACP will automatically be assigned the next available port-channel ID.
4 Command Line Interface Current status: Created by: Link status: Operation speed-duplex: Flow control type: Member Ports: Console# Lacp Up 1000full None Eth1/10, Eth1/11, Eth1/12, lacp system-priority This command configures a port's LACP system priority. Use the no form to restore the default setting. Syntax lacp {actor | partner} system-priority priority no lacp {actor | partner} system-priority • actor - The local side an aggregate link. • partner - The remote side of an aggregate link.
Link Aggregation Commands 4 lacp admin-key (Ethernet Interface) This command configures a port's LACP administration key. Use the no form to restore the default setting. Syntax lacp {actor | partner} admin-key key [no] lacp {actor | partner} admin-key • actor - The local side an aggregate link. • partner - The remote side of an aggregate link. • key - The port admin key must be set to the same value for ports that belong to the same link aggregation group (LAG).
4 Command Line Interface Default Setting 0 Command Mode Interface Configuration (Port Channel) Command Usage • Ports are only allowed to join the same LAG if (1) the LACP system priority matches, (2) the LACP port admin key matches, and (3) the LACP port channel key matches (if configured). • If the port channel admin key (lacp admin key - Port Channel) is not set when a channel group is formed (i.e.
Link Aggregation Commands 4 Example Console(config)#interface ethernet 1/5 Console(config-if)#lacp actor port-priority 128 show lacp This command displays LACP information. Syntax show lacp [port-channel] {counters | internal | neighbors | sys-id} • • • • • port-channel - Local identifier for a link aggregation group. (Range: 1-12) counters - Statistics for LACP protocol messages. internal - Configuration settings and operational state for local side.
4 Command Line Interface Console#show lacp 1 internal Port channel: 1 ------------------------------------------------------------------------Oper Key: 3 Admin Key: 0 Eth 1/ 2 ------------------------------------------------------------------------LACPDUs Internal: 30 sec LACP System Priority: 32768 LACP Port Priority: 32768 Admin Key: 3 Oper Key: 3 Admin State: defaulted, aggregation, long timeout, LACP-activity Oper State: distributing, collecting, synchronization, aggregation, long timeout, LACP-activi
Link Aggregation Commands 4 Console#show lacp 1 neighbors Port channel 1 neighbors ------------------------------------------------------------------------Eth 1/1 ------------------------------------------------------------------------Partner Admin System ID: 32768, 00-00-00-00-00-00 Partner Oper System ID: 32768, 00-01-F4-78-AE-C0 Partner Admin Port Number: 2 Partner Oper Port Number: 2 Port Admin Priority: 32768 Port Oper Priority: 32768 Admin Key: 0 Oper Key: 3 Admin State: defaulted, distributing, col
4 Command Line Interface Console#show lacp sysid Port Channel System Priority System MAC Address ------------------------------------------------------------------------1 32768 00-30-F1-8F-2C-A7 2 32768 00-30-F1-8F-2C-A7 3 32768 00-30-F1-8F-2C-A7 4 32768 00-30-F1-8F-2C-A7 5 32768 00-30-F1-8F-2C-A7 6 32768 00-30-F1-8F-2C-A7 7 32768 00-30-F1-D4-73-A0 8 32768 00-30-F1-D4-73-A0 9 32768 00-30-F1-D4-73-A0 10 32768 00-30-F1-D4-73-A0 11 32768 00-30-F1-D4-73-A0 12 32768 00-30-F1-D4-73-A0 . . .
Address Table Commands 4 mac-address-table static This command maps a static address to a destination port in a VLAN. Use the no form to remove an address. Syntax mac-address-table static mac-address interface interface vlan vlan-id [action] no mac-address-table static mac-address vlan vlan-id • mac-address - MAC address. • interface • ethernet unit/port - unit - Stack unit48. (Range: 1-1) - port - Port number.
4 Command Line Interface clear mac-address-table dynamic This command removes any learned entries from the forwarding database and clears the transmit and receive counts for any static or system configured entries. Default Setting None Command Mode Privileged Exec Example Console#clear mac-address-table dynamic Console# show mac-address-table This command shows classes of entries in the bridge-forwarding database.
Address Table Commands 4 means to match a bit and “1” means to ignore a bit. For example, a mask of 00-00-00-00-00-00 means an exact match, and a mask of FF-FF-FF-FF-FF-FF means “any.” • The maximum number of address entries is 8191. Example Console#show mac-address-table Interface MAC Address VLAN Type --------- ----------------- ---- ----------------Eth 1/ 1 00-e0-29-94-34-de 1 Delete-on-reset Console# mac-address-table aging-time This command sets the aging time for entries in the address table.
4 Command Line Interface Spanning Tree Commands This section includes commands that configure the Spanning Tree Algorithm (STA) globally for the switch, and commands that configure STA for the selected interface.
4 Spanning Tree Commands spanning-tree This command enables the Spanning Tree Algorithm globally for the switch. Use the no form to disable it. Syntax [no] spanning-tree Default Setting Spanning tree is enabled. Command Mode Global Configuration Command Usage The Spanning Tree Algorithm (STA) can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers.
4 Command Line Interface members may be inadvertently disabled to prevent network loops, thus isolating group members. When operating multiple VLANs, we recommend selecting the MSTP option. • Rapid Spanning Tree Protocol RSTP supports connections to either STP or RSTP nodes by monitoring the incoming protocol messages and dynamically adjusting the type of protocol messages the RSTP node transmits, as described below: - STP Mode – If the switch receives an 802.
Spanning Tree Commands 4 Command Usage This command sets the maximum time (in seconds) the root device will wait before changing states (i.e., discarding to learning to forwarding). This delay is required because every device must receive information about topology changes before it starts to forward frames. In addition, each port needs time to listen for conflicting information that would make it return to the discarding state; otherwise, temporary data loops might result.
4 Command Line Interface Default Setting 20 seconds Command Mode Global Configuration Command Usage This command sets the maximum time (in seconds) a device can wait without receiving a configuration message before attempting to reconfigure. All device ports (except for designated ports) should receive configuration messages at regular intervals. Any port that ages out STA information (provided in the last configuration message) becomes the designated port for the attached LAN.
Spanning Tree Commands 4 spanning-tree pathcost method This command configures the path cost method used for Rapid Spanning Tree and Multiple Spanning Tree. Use the no form to restore the default. Syntax spanning-tree pathcost method {long | short} no spanning-tree pathcost method • long - Specifies 32-bit based values that range from 1-200,000,000. • short - Specifies 16-bit based values that range from 1-65535.
4 Command Line Interface spanning-tree mst-configuration This command changes to Multiple Spanning Tree (MST) configuration mode. Default Setting • No VLANs are mapped to any MST instance. • The region name is set the switch’s MAC address.
Spanning Tree Commands 4 and the same instance (on each bridge) with the same set of VLANs. Also, note that RSTP treats each MSTI region as a single node, connecting all regions to the Common Spanning Tree. Example Console(config-mstp)#mst 1 vlan 2-5 Console(config-mstp)# mst priority This command configures the priority of a spanning tree instance. Use the no form to restore the default.
4 Command Line Interface Default Setting Switch’s MAC address Command Mode MST Configuration Command Usage The MST region name and revision number (page 4-178) are used to designate a unique MST region. A bridge (i.e., spanning-tree compliant device such as this switch) can only belong to one MST region. And all bridges in the same region must be configured with the same MST instances.
Spanning Tree Commands 4 max-hops This command configures the maximum number of hops in the region before a BPDU is discarded. Use the no form to restore the default. Syntax max-hops hop-number hop-number - Maximum hop number for multiple spanning tree. (Range: 1-40) Default Setting 20 Command Mode MST Configuration Command Usage An MSTI region is treated as a single node by the STP and RSTP protocols. Therefore, the message age for BPDUs inside an MSTI region is never changed.
4 Command Line Interface spanning-tree cost This command configures the spanning tree path cost for the specified interface. Use the no form to restore the default. Syntax spanning-tree cost cost no spanning-tree cost cost - The path cost for the port.
Spanning Tree Commands 4 Default Setting 128 Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage • This command defines the priority for the use of a port in the Spanning Tree Algorithm. If the path cost for all ports on a switch are the same, the port with the highest priority (that is, lowest value) will be configured as an active link in the spanning tree. • Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled.
4 Command Line Interface Example Console(config)#interface ethernet ethernet 1/5 Console(config-if)#spanning-tree edge-port Console(config-if)# Related Commands spanning-tree portfast (4-182) spanning-tree portfast This command sets an interface to fast forwarding. Use the no form to disable fast forwarding.
Spanning Tree Commands 4 spanning-tree link-type This command configures the link type for Rapid Spanning Tree and Multiple Spanning Tree. Use the no form to restore the default. Syntax spanning-tree link-type {auto | point-to-point | shared} no spanning-tree link-type • auto - Automatically derived from the duplex mode setting. • point-to-point - Point-to-point link. • shared - Shared medium.
4 Command Line Interface Default Setting By default, the system automatically detects the speed and duplex mode used on each port, and configures the path cost according to the values shown below. Path cost “0” is used to indicate auto-configuration mode.
4 Spanning Tree Commands Command Usage • This command defines the priority for the use of an interface in the multiple spanning-tree. If the path cost for all interfaces on a switch are the same, the interface with the highest priority (that is, lowest value) will be configured as an active link in the spanning tree. • Where more than one interface is assigned the highest priority, the interface with lowest numeric identifier will be enabled.
4 Command Line Interface show spanning-tree This command shows the configuration for the common spanning tree (CST) or for an instance within the multiple spanning tree (MST). Syntax show spanning-tree [interface | mst instance_id] • interface • ethernet unit/port - unit - Stack unit51. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) • instance_id - Instance identifier of the multiple spanning tree.
Spanning Tree Commands 4 Example Console#show spanning-tree Spanning-tree information --------------------------------------------------------------Spanning tree mode: MSTP Spanning tree enable/disable: enable Instance: 0 Vlans configuration: 1-4094 Priority: 32768 Bridge Hello Time (sec.): 2 Bridge Max Age (sec.): 20 Bridge Forward Delay (sec.): 15 Root Hello Time (sec.): 2 Root Max Age (sec.): 20 Root Forward Delay (sec.): 15 Max hops: 20 Remaining hops: 20 Designated Root: 32768.0.
4 Command Line Interface show spanning-tree mst configuration This command shows the configuration of the multiple spanning tree.
VLAN Commands 4 vlan database This command enters VLAN database mode. All commands in this mode will take effect immediately. Default Setting None Command Mode Global Configuration Command Usage • Use the VLAN database command mode to add, change, and delete VLANs. After finishing configuration changes, you can display the VLAN settings by entering the show vlan command. • Use the interface vlan command mode to define the port membership mode and add or remove ports from a VLAN.
4 Command Line Interface Command Usage • no vlan vlan-id deletes the VLAN. • no vlan vlan-id name removes the VLAN name. • no vlan vlan-id state returns the VLAN to the default state (i.e., active). • You can configure up to 255 VLANs on the switch. Example The following example adds a VLAN, using VLAN ID 105 and name RD5. The VLAN is activated by default.
VLAN Commands 4 Example The following example shows how to set the interface configuration mode to VLAN 1, and then assign an IP address to the VLAN: Console(config)#interface vlan 1 Console(config-if)#ip address 192.168.1.254 255.255.255.0 Console(config-if)# Related Commands shutdown (4-148) switchport mode This command configures the VLAN membership mode for a port. Use the no form to restore the default.
4 Command Line Interface switchport acceptable-frame-types This command configures the acceptable frame types for a port. Use the no form to restore the default. Syntax switchport acceptable-frame-types {all | tagged} no switchport acceptable-frame-types • all - The port accepts all frames, tagged or untagged. • tagged - The port only receives tagged frames.
VLAN Commands 4 • If ingress filtering is enabled and a port receives frames tagged for VLANs for which it is not a member, these frames will be discarded. • Ingress filtering does not affect VLAN independent BPDU frames, such as GVRP or STA. However, they do affect VLAN dependent BPDU frames, such as GMRP.
4 Command Line Interface switchport allowed vlan This command configures VLAN groups on the selected interface. Use the no form to restore the default. Syntax switchport allowed vlan {add vlan-list [tagged | untagged] | remove vlan-list} no switchport allowed vlan • add vlan-list - List of VLAN identifiers to add. • remove vlan-list - List of VLAN identifiers to remove. • vlan-list - Separate nonconsecutive VLAN identifiers with a comma and no spaces; use a hyphen to designate a range of IDs.
VLAN Commands 4 switchport forbidden vlan This command configures forbidden VLANs. Use the no form to remove the list of forbidden VLANs. Syntax switchport forbidden vlan {add vlan-list | remove vlan-list} no switchport forbidden vlan • add vlan-list - List of VLAN identifiers to add. • remove vlan-list - List of VLAN identifiers to remove. • vlan-list - Separate nonconsecutive VLAN identifiers with a comma and no spaces; use a hyphen to designate a range of IDs. Do not enter leading zeros.
4 Command Line Interface show vlan This command shows VLAN information. Syntax show vlan [id vlan-id | name vlan-name] • id - Keyword to be followed by the VLAN ID. vlan-id - ID of the configured VLAN. (Range: 1-4094, no leading zeroes) • name - Keyword to be followed by the VLAN name. vlan-name - ASCII string from 1 to 32 characters. Default Setting Shows all VLANs.
VLAN Commands 4 Configuring Private VLANs Private VLANs provide port-based security and isolation between ports within the assigned VLAN. This section describes commands used to configure private VlANs. Table 4-63 Private VLAN Commands Command Function Mode pvlan Enables and configured private VLANS GC Page 4-197 show pvlan Displays the configured private VLANS PE 4-198 pvlan This command enables or configures a private VLAN. Use the no form to disable the private VLAN.
4 Command Line Interface show pvlan This command displays the configured private VLAN. Command Mode Privileged Exec Example Console#show pvlan Private VLAN status: Enabled Up-link port: Ethernet 1/12 Down-link port: Ethernet 1/5 Ethernet 1/6 Ethernet 1/7 Ethernet 1/8 Console# Configuring Protocol-based VLANs The network devices required to support multiple protocols cannot be easily grouped into a common VLAN.
4 VLAN Commands 3. Then map the protocol for each interface to the appropriate VLAN using the protocol-vlan protocol-group command (Interface Configuration mode). protocol-vlan protocol-group (Configuring Groups) This command creates a protocol group, or to add specific protocols to a group. Use the no form to remove a protocol group.
4 Command Line Interface Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage • When creating a protocol-based VLAN, only assign interfaces via this command. If you assign interfaces using any of the other VLAN commands (such as vlan on page 4-189), these interfaces will admit traffic of any protocol type into the associated VLAN.
VLAN Commands 4 show interfaces protocol-vlan protocol-group This command shows the mapping from protocol groups to VLANs for the selected interfaces. Syntax show interfaces protocol-vlan protocol-group [interface] interface • ethernet unit/port - unit - Stack unit53. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting The mapping for all interfaces is displayed.
4 Command Line Interface GVRP and Bridge Extension Commands GARP VLAN Registration Protocol defines a way for switches to exchange VLAN information in order to automatically register VLAN members on interfaces across the network. This section describes how to enable GVRP for individual interfaces and globally for the switch, as well as how to display default configuration settings for the Bridge Extension MIB.
GVRP and Bridge Extension Commands 4 show bridge-ext This command shows the configuration for bridge extension commands. Default Setting None Command Mode Privileged Exec Command Usage See “Displaying Basic VLAN Information” on page 3-138 and “Displaying Bridge Extension Capabilities” on page 3-15 for a description of the displayed items.
4 Command Line Interface show gvrp configuration This command shows if GVRP is enabled. Syntax show gvrp configuration [interface] interface • ethernet unit/port - unit - Stack unit54. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting Shows both global and interface-specific configuration.
GVRP and Bridge Extension Commands 4 Command Usage • Group Address Registration Protocol is used by GVRP and GMRP to register or deregister client attributes for client services within a bridged LAN. The default values for the GARP timers are independent of the media access method or data rate. These values should not be changed unless you are experiencing difficulties with GMRP or GVRP registration/deregistration. • Timer values are applied to GVRP for all the ports on all VLANs.
4 Command Line Interface Related Commands garp timer (4-204) Priority Commands The commands described in this section allow you to specify which data packets have greater precedence when traffic is buffered in the switch due to congestion. This switch supports CoS with eight priority queues for each port. Data packets in a port’s high-priority queue will be transmitted before those in the lower-priority queues.
Priority Commands 4 queue mode This command sets the queue mode to strict priority or Weighted Round-Robin (WRR) for the class of service (CoS) priority queues. Use the no form to restore the default value. Syntax queue mode {strict | wrr} no queue mode • strict - Services the egress queues in sequential order, transmitting all traffic in the higher priority queues before servicing lower priority queues.
4 Command Line Interface Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage • The precedence for priority mapping is IP Port, IP Precedence or IP DSCP, and default switchport priority. • The default priority applies for an untagged frame received on a port set to accept all frame types (i.e, receives both untagged and tagged frames). This priority does not apply to IEEE 802.1Q VLAN tagged frames. If the incoming frame is an IEEE 802.1Q VLAN tagged frame, the IEEE 802.
Priority Commands 4 Example This example shows how to assign WRR weights to each of the priority queues: Console#configure Console(config)#int eth 1/5 Console(config-if)#queue bandwidth 1 3 5 7 9 11 13 15 Console(config-if)# Related Commands show queue bandwidth (4-210) queue cos-map This command assigns class of service (CoS) values to the priority queues (i.e., hardware output queues 0 - 7). Use the no form set the CoS map to the default values. Syntax queue cos-map queue_id [cos1 ...
4 Command Line Interface Example The following example shows how to change the CoS assignments to a one-to-one mapping: Console(config)#interface ethernet 1/1 Console(config-if)#queue cos-map 0 0 Console(config-if)#queue cos-map 1 1 Console(config-if)#queue cos-map 2 2 Console(config-if)#exit Console#show queue cos-map ethernet 1/1 Information of Eth 1/1 Traffic Class : 0 1 2 3 4 5 6 7 Priority Queue: 0 1 2 3 4 5 6 7 Console# Related Commands show queue cos-map (4-211) show queue mode This command shows
Priority Commands 4 Example Console#show queue bandwidth Information of Eth 1/1 Queue ID Weight -------- -----0 1 1 2 2 4 3 6 4 8 5 10 6 12 7 14 . . . show queue cos-map This command shows the class of service priority map. Syntax show queue cos-map [interface] interface • ethernet unit/port - unit - Stack unit56. (Range: 1-1) - port - Port number.
4 Command Line Interface Priority Commands (Layer 3 and 4) Table 4-69 Priority Commands (Layer 3 and 4) Command Function Mode map ip port Enables TCP/UDP class of service mapping GC Page map ip port Maps TCP/UDP socket to a class of service IC 4-212 map ip precedence Enables IP precedence class of service mapping GC 4-213 map ip precedence Maps IP precedence value to a class of service IC 4-214 map ip dscp Enables IP DSCP class of service mapping GC 4-214 map ip dscp Maps IP DSCP v
Priority Commands 4 Default Setting None Command Mode Interface Configuration (Ethernet, Port Channel) Command Usage • The precedence for priority mapping is IP Port, IP Precedence or IP DSCP, and default switchport priority. • This command sets the IP port priority for all interfaces.
4 Command Line Interface map ip precedence (Interface Configuration) This command sets IP precedence priority (i.e., IP Type of Service priority). Use the no form to restore the default table. Syntax map ip precedence ip-precedence-value cos cos-value no map ip precedence • precedence-value - 3-bit precedence value. (Range: 0-7) • cos-value - Class-of-Service value (Range: 0-7) Default Setting The list below shows the default priority mapping.
Priority Commands 4 Command Usage • The precedence for priority mapping is IP Port, IP Precedence or IP DSCP, and default switchport priority. • IP Precedence and IP DSCP cannot both be enabled. Enabling one of these priority types will automatically disable the other type. Example The following example shows how to enable IP DSCP mapping globally: Console(config)#map ip dscp Console(config)# map ip dscp (Interface Configuration) This command sets IP DSCP priority (i.e.
4 Command Line Interface • DSCP priority values are mapped to default Class of Service values according to recommendations in the IEEE 802.1p standard, and then subsequently mapped to the eight hardware priority queues. • This command sets the IP DSCP priority for all interfaces.
Priority Commands 4 show map ip precedence This command shows the IP precedence priority map. Syntax show map ip precedence [interface] interface • ethernet unit/port - unit - Stack unit58. (Range: 1-1) - port - Port number.
4 Command Line Interface show map ip dscp This command shows the IP DSCP priority map. Syntax show map ip dscp [interface] interface • ethernet unit/port - unit - Stack unit59. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting None Command Mode Privileged Exec Example Console#show map ip dscp ethernet 1/1 DSCP mapping status: disabled Port DSCP COS --------- ---- --Eth 1/ 1 0 0 Eth 1/ 1 1 0 Eth 1/ 1 2 0 Eth 1/ 1 3 0 . . .
Quality of Service Commands 4 Quality of Service Commands The commands described in this section are used to configure Differentiated Services (DiffServ) classification criteria and service policies. You can classify traffic based on access lists, IP Precedence or DSCP values, or VLANs. Using access lists allows you select traffic based on Layer 2, Layer 3, or Layer 4 information contained in each packet.
4 Command Line Interface Notes: 1. You can only configure one rule per Class Map. However, you can include multiple classes in a Policy Map. 2. You must create a Class Map before creating a Policy Map. class-map This command creates a class map used for matching packets to the specified class, and enters Class Map configuration mode. Use the no form to delete a class map and return to Global configuration mode.
Quality of Service Commands 4 match This command defines the criteria used to classify traffic. Use the no form to delete the matching criteria. Syntax [no] match {access-list acl-name | ip dscp dscp | ip precedence ip-precedence | vlan vlan} • acl-name - Name of the access control list. Any type of ACL can be specified, including standard or extended IP ACLs and MAC ACLs. (Range: 1-16 characters) • dscp - A DSCP value. (Range: 0-63) • ip-precedence - An IP Precedence value. (Range: 0-7) • vlan - A VLAN.
4 Command Line Interface This example creates a class map call “rd_class#3,” and sets it to match packets marked for VLAN 1: Console(config)#class-map rd_class#3 match-any Console(config-cmap)#match vlan 1 Console(config-cmap)#exit Console(config)#access-list mac mask-precedence in Console(config-ip-mask-acl)#mask any any vid 1 Console(config-ip-mask-acl)# policy-map This command creates a policy map that can be attached to multiple interfaces, and enters Policy Map configuration mode.
Quality of Service Commands 4 class This command defines a traffic classification upon which a policy can act, and enters Policy Map Class configuration mode. Use the no form to delete a class map and return to Policy Map configuration mode. Syntax [no] class class-map-name class-map-name - Name of the class map. (Range: 1-32 characters) Default Setting None Command Mode Policy Map Configuration Command Usage • Use the policy-map command to specify a policy map and enter Policy Map configuration mode.
4 Command Line Interface set This command services IP traffic by setting a CoS, DSCP, or IP Precedence value in a matching packet (as specified by the match command on page 4-221). Use the no form to remove the traffic classification. Syntax [no] set {cos new-cos | ip dscp new-dscp | ip precedence new-precedence} • new-cos - New Class of Service (CoS) value. (Range: 0-7) • new-dscp - New Differentiated Service Code Point (DSCP) value. (Range: 0-63) • new-precedence - New IP Precedence value.
Quality of Service Commands 4 Command Usage • You can configure up to 63 policers (i.e., class maps) for Fast Ethernet and Gigabit Ethernet ingress ports. • Policing is based on a token bucket, where bucket depth (i.e., the maximum burst before the bucket overflows) is by specified the burst-byte field, and the average rate tokens are removed from the bucket is by specified by the rate-bps option.
4 Command Line Interface show class-map This command displays the QoS class maps which define matching criteria used for classifying traffic. Syntax show class-map [class-map-name] class-map-name - Name of the class map. (Range: 1-32 characters) Default Setting Displays all class maps.
Quality of Service Commands 4 Example Console#show policy-map Policy Map rd_policy class rd_class set ip dscp 3 Console#show policy-map rd_policy class rd_class Policy Map rd_policy class rd_class set ip dscp 3 Console# show policy-map interface This command displays the service policy assigned to the specified interface. Syntax show policy-map interface interface input interface • ethernet unit/port - unit - Stack unit60. (Range: 1-1) - port - Port number.
4 Command Line Interface Multicast Filtering Commands This switch uses IGMP (Internet Group Management Protocol) to query for any attached hosts that want to receive a specific multicast service. It identifies the ports containing hosts requesting a service and sends data out to those ports only. It then propagates the service request up to any neighboring multicast switch/router to ensure that it will continue to receive the multicast service.
4 Multicast Filtering Commands The following example enables IGMP snooping. Console(config)#ip igmp snooping Console(config)# ip igmp snooping vlan static This command adds a port to a multicast group. Use the no form to remove the port. Syntax [no] ip igmp snooping vlan vlan-id static ip-address interface • vlan-id - VLAN ID (Range: 1-4094) • ip-address - IP address for multicast group • interface • ethernet unit/port - unit - Stack unit61. (Range: 1-1) - port - Port number.
4 Command Line Interface Command Usage • All systems on the subnet must support the same version. If there are legacy devices in your network that only support Version 1, you will also have to configure this switch to use Version 1. • Some commands are only enabled for IGMPv2, including ip igmp query-max-response-time and ip igmp query-timeout.
4 Multicast Filtering Commands Command Mode Privileged Exec Command Usage Member types displayed include IGMP or USER, depending on selected options. Example The following shows the multicast entries learned through IGMP snooping for VLAN 1: Console#show mac-address-table multicast vlan 1 igmp-snooping VLAN M'cast IP addr. Member ports Type ---- --------------- ------------ ------1 224.1.2.
4 Command Line Interface Example Console(config)#ip igmp snooping querier Console(config)# ip igmp snooping query-count This command configures the query count. Use the no form to restore the default. Syntax ip igmp snooping query-count count no ip igmp snooping query-count count - The maximum number of queries issued for which there has been no response before the switch takes action to drop a client from the multicast group.
Multicast Filtering Commands 4 Command Mode Global Configuration Example The following shows how to configure the query interval to 100 seconds: Console(config)#ip igmp snooping query-interval 100 Console(config)# ip igmp snooping query-max-response-time This command configures the query report delay. Use the no form to restore the default. Syntax ip igmp snooping query-max-response-time seconds no ip igmp snooping query-max-response-time seconds - The report delay advertised in IGMP queries.
4 Command Line Interface ip igmp snooping router-port-expire-time This command configures the query timeout. Use the no form to restore the default. Syntax ip igmp snooping router-port-expire-time seconds no ip igmp snooping router-port-expire-time seconds - The time the switch waits after the previous querier stops before it considers the router port (i.e., the interface which had been receiving query packets) to have expired.
Multicast Filtering Commands 4 ip igmp snooping vlan mrouter This command statically configures a multicast router port. Use the no form to remove the configuration. Syntax [no] ip igmp snooping vlan vlan-id mrouter interface • vlan-id - VLAN ID (Range: 1-4094) • interface • ethernet unit/port - unit - Stack unit62. (Range: 1-1) - port - Port number. (Range: 1-28) • port-channel channel-id (Range: 1-12) Default Setting No static multicast router ports are configured.
4 Command Line Interface Command Usage Multicast router port types displayed include Static or Dynamic.
Multicast Filtering Commands 4 Example Console(config)#interface vlan 1 Console(config-if)#ip igmp Console(config-if)#end Console#show ip igmp interface Vlan 1 is up IGMP is enable, version is 2 Robustness variable is 2 Query interval is 125 sec Query Max Response Time is 10 sec, Last Member Query Interval is 1 sec Querier is 10.1.0.253 Console# Related Commands ip igmp snooping (4-228) show ip igmp snooping (4-230) ip igmp robustval This command specifies the robustness (i.e.
4 Command Line Interface ip igmp query-interval This command configures the frequency at which host query messages are sent. Use the no form to restore the default. Syntax ip igmp query-interval seconds no ip igmp query-interval seconds - The frequency at which the switch sends IGMP host-query messages.
Multicast Filtering Commands 4 Command Usage • The switch must be using IGMPv2 for this command to take effect. • This command defines how long any responder (i.e., client or router) still in the group has to respond to a query message before the router deletes the group. • By varying the Maximum Response Interval, you can tune the burstiness of IGMP messages passed on the subnet; where larger values make the traffic less bursty, as host responses are spread out over a larger interval.
4 Command Line Interface ip igmp version This command configures the IGMP version used on an interface. Use the no form of this command to restore the default. Syntax ip igmp version {1 | 2} no ip igmp version • 1 - IGMP Version 1 • 2 - IGMP Version 2 Default Setting IGMP Version 2 Command Mode Interface Configuration (VLAN) Command Usage • All routers on the subnet must support the same version. However, the multicast hosts on the subnet may support either IGMP version 1 or 2.
Multicast Filtering Commands 4 The following example shows the IGMP configuration for VLAN 1, as well as the device currently serving as the IGMP querier for this multicast service. Console#show ip igmp interface vlan 1 Vlan 1 is up IGMP is enable, version is 2 Robustness variable is 2 Query interval is 125 sec Query Max Response Time is 10 sec, Last Member Query Interval is 1 sec Querier is 10.1.0.253 Console# clear ip igmp group This command deletes entries from the IGMP cache.
4 Command Line Interface Command Usage • This command displays information for multicast groups learned via IGMP, not static groups. • If the switch receives an IGMP Version 1 Membership Report, it sets a timer to note that there are Version 1 hosts present which are members of the group for which it heard the report. • If there are Version 1 hosts present for a particular group, the switch will ignore any Leave Group messages that it receives for that group.
IP Interface Commands 4 IP Interface Commands There are no IP addresses assigned to this router by default. You must manually configure a new address to manage the router over your network or to connect the router to existing IP subnets. You may also need to a establish a default gateway between this device and management stations or other devices that exist on another network segment (if routing is not enabled).
4 Command Line Interface Default Setting DHCP Command Mode Interface Configuration (VLAN) Command Usage • If this router is directly connected to end node devices (or connected to end nodes via shared media) that will be assigned to a specific subnet, then you must create a router interface for each VLAN that will support routing. The router interface consists of an IP address and subnet mask.
IP Interface Commands 4 Related Commands ip dhcp restart client (4-122) ip default-gateway This command specifies the default gateway for destinations not found in the local routing tables. Use the no form to remove a default gateway. Syntax ip default-gateway gateway no ip default-gateway gateway - IP address of the default gateway Default Setting No static route is established.
4 Command Line Interface Related Commands show ip redirects (4-246) show ip redirects This command shows the default gateway configured for this device. Default Setting None Command Mode Privileged Exec Example Console#show ip redirects ip default gateway 10.1.0.254 Console# Related Commands ip default-gateway (4-245) ping This command sends ICMP echo request packets to another node on the network. Syntax ping host [count count][size size] • host - IP address or IP alias of the host.
IP Interface Commands 4 - Network or host unreachable - The gateway found no corresponding entry in the route table. • Press to stop pinging. Example Console#ping 10.1.0.9 Type ESC to abort. PING to 10.1.0.9, by 5 32-byte payload ICMP packets, timeout is 5 seconds response time: 10 ms response time: 10 ms response time: 10 ms response time: 10 ms response time: 0 ms Ping statistics for 10.1.0.
4 Command Line Interface Command Usage • The ARP cache is used to map 32-bit IP addresses into 48-bit hardware (i.e., Media Access Control) addresses. This cache includes entries for hosts and other routers on local network interfaces defined on this router. • The maximum number of static entries allowed in the ARP cache is 128. • You may need to enter a static entry in the cache if there is no response to an ARP broadcast message.
IP Interface Commands 4 clear arp-cache This command deletes all dynamic entries from the Address Resolution Protocol (ARP) cache. Command Mode Privileged Exec Example This example clears all dynamic entries in the ARP cache. Console#clear arp-cache This operation will delete all the dynamic entries in ARP Cache. Are you sure to continue this operation (y/n)?y Console# show arp Use this command to display entries in the Address Resolution Protocol (ARP) cache.
4 Command Line Interface ip proxy-arp This command enables proxy Address Resolution Protocol (ARP). Use the no form to disable proxy ARP. Syntax [no] ip proxy-arp Default Setting Disabled Command Mode Interface Configuration (VLAN) Command Usage Proxy ARP allows a non-routing device to determine the MAC address of a host on another subnet or network.
IP Routing Commands 4 Global Routing Configuration Table 4-83 Global Routing Configuration Commands Command Function Mode Page ip routing Enables static and dynamic IP routing GC 4-251 ip route Configures static routes GC 4-251 clear ip route Deletes specified entries from the routing table PE 4-252 show ip route Displays specified entries in the routing table PE 4-253 show ip host-route Displays displays the interface associated with known routes PE 4-254 show ip traffic Displays
4 Command Line Interface • gateway – IP address of the gateway used for this route. • metric – Selected RIP cost for this interface. (Range: 1-5, default: 1) • * – Removes all static routing table entries. Default Setting No static routes are configured. Command Mode Global Configuration Command Usage • You can configure up to 256 static routes. • Static routes take precedence over dynamically learned routes. • Static routes are included in RIP updates periodically sent by the router.
4 IP Routing Commands show ip route This command displays information in the IP routing table. Syntax show ip route [config | address [netmask]] • config – Displays all static routing entries. • address – IP address of the destination network, subnetwork or host for which routing information is to be displayed. • netmask - Network mask for the associated IP subnet. This mask identifies the host address bits used for routing to specific subnets.
4 Command Line Interface show ip host-route This command displays the interface associated with known routes. Command Mode Privileged Exec Example Console#show ip host-route Total count: 0 IP address -------------------192.168. 1.250 10. 2. 48. 2 10. 2. 5. 6 10. 3. 9.
IP Routing Commands 4 show ip traffic This command displays statistics for IP, ICMP, UDP, TCP and ARP protocols. Command Mode Privileged Exec Command Usage For a description of the information shown by this command, see “Displaying Statistics for IP Protocols” on page 3-217.
4 Command Line Interface Routing Information Protocol (RIP) Table 4-86 Routing Information Protocol Commands Command Function Mode Page router rip Enables the RIP routing protocol GC 4-256 timers basic Sets basic timers, including update, timeout, garbage collection RC 4-257 network Specifies the network interfaces that are to use RIP routing RC 4-258 neighbor Defines a neighboring router with which to exchange information RC 4-258 version Specifies the RIP version to use on all network
IP Routing Commands 4 timers basic This command configures the RIP update timer, timeout timer, and garbagecollection timer. Use the no form to restore the defaults. Syntax timers basic update-seconds no timers basic update-seconds – Sets the update timer to the specified value, sets the timeout time value to 6 times the update time, and sets the garbagecollection timer to 4 times the update time.
4 Command Line Interface network This command specifies the network interfaces that will be included in the RIP routing process. Use the no form to remove an entry. Syntax [no] network subnet-address subnet-address – IP address of a network directly connected to this router. Command Mode Router Configuration Default Setting No networks are specified. Command Usage • RIP only sends updates to interfaces specified by this command.
IP Routing Commands 4 Command Usage This command can be used to configure a static neighbor with which this router will exchange information, rather than relying on broadcast messages generated by the RIP protocol. Example Console(config-router)#neighbor 10.2.0.254 Console(config-router)# version This command specifies a RIP version used globally by the router. Use the no form to restore the default value.
4 Command Line Interface ip rip receive version This command specifies a RIP version to receive on an interface. Use the no form to restore the default value. Syntax ip rip receive version {none | 1 | 2 | 1 2} no ip rip receive version • • • • none - Does not accept incoming RIP packets. 1 - Accepts only RIPv1 packets. 2 - Accepts only RIPv2 packets.
IP Routing Commands 4 ip rip send version This command specifies a RIP version to send on an interface. Use the no form to restore the default value. Syntax ip rip send version {none | 1 | 2 | v2-broadcast} no ip rip send version • • • • none - Does not transmit RIP updates. 1 - Sends only RIPv1 packets. 2 - Sends only RIPv2 packets. v2-broadcast - Route information is broadcast to other routers with RIPv2.
4 Command Line Interface ip split-horizon This command enables split-horizon or poison-reverse (a variation) on an interface. Use the no form to disable split-horizon. Syntax ip split-horizon [poison-reverse] no ip split-horizon poison-reverse - Enables poison-reverse on the current interface. Command Mode Interface Configuration (VLAN) Default Setting split-horizon Command Usage • Split horizon never propagates routes back to an interface from which they have been acquired.
IP Routing Commands 4 • For authentication to function properly, both the sending and receiving interface must be configured with the same password. Example This example sets an authentication password of “small” to verify incoming routing messages and to tag outgoing routing messages.
4 Command Line Interface show rip globals This command displays global configuration settings for RIP. Command Mode Privileged Exec Example Console#show rip globals RIP Process: Enabled Update Time in Seconds: 30 Number of Route Change: 0 Number of Queries: 1 Console# Table 4-87 show rip globals - display description Field Description RIP Process Indicates if RIP has been enabled or disabled. Update Time in Seconds The interval at which RIP advertises known route information.
IP Routing Commands 4 Example Console#show ip rip configuration Interface SendMode ReceiveMode Poison Authentication --------------- --------------- ------------- -------------- -----------------10.1.0.253 rip1Compatible RIPv1Orv2 SplitHorizon noAuthentication 10.1.1.253 rip1Compatible RIPv1Orv2 SplitHorizon noAuthentication Console#show ip rip status Interface RcvBadPackets RcvBadRoutes SendUpdates --------------- --------------- -------------- --------------10.1.0.253 0 0 13 10.1.1.
4 Command Line Interface Open Shortest Path First (OSPF) Table 4-89 Open Shortest Path First Commands Command Function Mode Page router ospf Enables or disables OSPF GC router-id Sets the router ID for this device RC 4-267 compatible rfc1583 Calculates summary route costs using RFC 1583 (OSPFv1) RC 4-268 default-information originate Generates a default external route into an autonomous system RC 4-269 timers spf Configures the hold time between consecutive SPF calculations RC 4-270
IP Routing Commands 4 Table 4-89 Open Shortest Path First Commands (Continued) Command Function Mode Page show ip ospf neighbor Displays neighbor information PE 4-295 show ip ospf summary-address Displays all summary address redistribution information PE 4-296 PE 4-296 show ip ospf virtual-links Displays parameters and the adjacency state of virtual links router ospf This command enables Open Shortest Path First (OSPF) routing for all IP interfaces on the router.
4 Command Line Interface Command Usage • The router ID must be unique for every router in the autonomous system. Using the default setting based on the lowest interface address ensures that each router ID is unique. Also, note that you cannot set the router ID to 0.0.0.0 or 255.255.255.255. • If this router already has registered neighbors, the new router ID will be used when the router is rebooted, or manually restarted by entering the no router ospf followed by the router ospf command.
IP Routing Commands 4 default-information originate This command generates a default external route into an autonomous system. Use the no form to disable this feature. Syntax default-information originate [always] [metric interface-metric] [metric-type metric-type] no default-information originate • always - Always advertise a default route to the local AS regardless of whether the router has a default route. (See “ip route” on page 4-251.) • interface-metric - Metric assigned to the default route.
4 Command Line Interface Related Commands ip route (4-251) redistribute (4-272) timers spf This command configures the hold time between making two consecutive shortest path first (SPF) calculations. Use the no form to restore the default value. Syntax timers spf spf-holdtime no timers spf spf-holdtime - Minimum time between two consecutive SPF calculations.
IP Routing Commands 4 Default Setting Disabled Command Usage • This command can be used to advertise routes between areas. • If routes are set to be advertised, the router will issue a Type 3 summary LSA for each address range specified with this command. • This router supports up 64 summary routes for area ranges. Example This example creates a summary address for all area routes in the range of 10.2.x.x. Console(config-router)#area 10.2.0.0 range 10.2.0.0 255.255.0.
4 Command Line Interface summary-address This command aggregates routes learned from other protocols. Use the no form to remove a summary address. Syntax [no] summary-address summary-address netmask • summary-address - Summary address covering a range of addresses. • netmask - Network mask for the summary route.
IP Routing Commands 4 Default Setting redistribution - none protocol - RIP and static metric-value - 0 type-metric - 2 Command Usage • This router supports redistribution for both RIP and static routes. • When you redistribute external routes into an OSPF autonomous system (AS), the router automatically becomes an autonomous system boundary router (ASBR).
4 Command Line Interface Command Usage • An area ID uniquely defines an OSPF broadcast area. The area ID 0.0.0.0 indicates the OSPF backbone for an autonomous system. Each router must be connected to the backbone via a direct connection or a virtual link. • Set the area ID to the same value for all routers on a network segment using the network mask to add one or more interfaces to an area.
IP Routing Commands 4 Command Usage • All routers in a stub must be configured with the same area ID. • Routing table space is saved in a stub by blocking Type-4 AS summary LSAs and Type 5 external LSAs. The default setting for this command completely isolates the stub by blocking Type-3 summary LSAs that advertise the default route for destinations external to the local area or the autonomous system.
4 Command Line Interface Command Usage • All routers in a NSSA must be configured with the same area ID. • An NSSA is similar to a stub, because when the router is an ABR, it can send a default route for other areas in the AS into the NSSA using the defaultinformation-originate keyword.
IP Routing Commands 4 • authentication - Specifies the authentication mode. If no optional parameters follow this keyword, then plain text authentication is used along with the password specified by the authentication-key. If message-digest authentication is specified, then the message-digest-key and md5 parameters must also be specified. If the null option is specified, then no authentication is performed on any OSPF routing protocol messages.
4 Command Line Interface Default Setting area-id: None router-id: None hello-interval: 10 seconds retransmit-interval: 5 seconds transmit-delay: 1 second dead-interval: 40 seconds authentication-key: None message-digest-key: None Command Usage • All areas must be connected to a backbone area (0.0.0.0) to maintain routing connectivity throughout the autonomous system. If it not possible to physically connect an area to the backbone, you can use a virtual link.
IP Routing Commands 4 Command Mode Interface Configuration (VLAN) Default Setting No authentication Command Usage • Before specifying plain-text password authentication for an interface, configure a password with the ip ospf authentication-key command. Before specifying MD5 authentication for an interface, configure the message-digest key-id and key with the ip ospf message-digest-key command.
4 Command Line Interface Example This example sets a password for the specified interface. Console(config)#interface vlan 1 Console(config-if)#ip ospf authentication-key badboy Console(config-if)# Related Commands ip ospf authentication (4-278) ip ospf message-digest-key This command enables message-digest (MD5) authentication on the specified interface and to assign a key-id and key to be used by neighboring routers. Use the no form to remove an existing key.
IP Routing Commands 4 Related Commands ip ospf authentication (4-278) ip ospf cost This command explicitly sets the cost of sending a packet on an interface. Use the no form to restore the default value. Syntax ip ospf cost cost no ip ospf cost cost - Link metric for this interface. Use higher values to indicate slower ports. (Range: 1-65535) Command Mode Interface Configuration (VLAN) Default Setting 1 Command Usage Interface cost reflects the port speed.
4 Command Line Interface Example Console(config)#interface vlan 1 Console(config-if)#ip ospf dead-interval 50 Console(config-if)# Related Commands ip ospf hello-interval (4-282) ip ospf hello-interval This command specifies the interval between sending hello packets on an interface. Use the no form to restore the default value. Syntax ip ospf hello-interval seconds no ip ospf hello-interval seconds - Interval at which hello packets are sent from an interface.
IP Routing Commands 4 Default Setting 1 Command Usage • Set the priority to zero to prevent a router from being elected as a DR or BDR. If set to any value other than zero, the router with the highest priority will become the DR and the router with the next highest priority becomes the BDR. If two or more routers are tied with the same highest priority, the router with the higher ID will be elected.
4 Command Line Interface ip ospf transmit-delay This command sets the estimated time to send a link-state update packet over an interface. Use the no form to restore the default value. Syntax ip ospf transmit-delay seconds no ip ospf transmit-delay seconds - Sets the estimated time required to send a link-state update. (Range: 1-65535) Command Mode Interface Configuration (VLAN) Default Setting 1 second Command Usage LSAs have their age incremented by this delay before transmission.
IP Routing Commands 4 Table 4-90 show ip ospf - display description Field Description Routing Process with ID Router ID Supports only single TOS (TOS0) route Type of service is not supported, so you can only assign one cost per interface It is an router type The types displayed include internal, area border, or autonomous system boundary routers Number of areas in this router The number of configured areas Area identifier The area address, and area type if backbone, NSSA or stub Number of inte
4 Command Line Interface show ip ospf database This command shows information about different OSPF Link State Advertisements (LSAs) stored in this router’s database.
IP Routing Commands 4 Command Mode Privileged Exec Examples The following shows output for the show ip ospf database command. Console#show ip ospf database Displaying Router Link States(Area 10.1.0.0) Link ID ADV Router Age Seq# Checksum --------------- --------------- ------ ----------- ----------10.1.1.252 10.1.1.252 26 0X80000005 0X89A1 10.1.1.253 10.1.1.253 23 0X80000002 0X8D9D Displaying Net Link States(Area 10.1.0.
4 Command Line Interface The following shows output when using the asbr-summary keyword. Console#show ip ospf database asbr-summary OSPF Router with id(10.1.1.253) Displaying Summary ASB Link States(Area 0.0.0.0) LS age: 433 Options: (No TOS-capability) LS Type: Summary Links (AS Boundary Router) Link State ID: 192.168.5.1 (AS Boundary Router's Router ID) Advertising Router: 192.168.1.5 LS Sequence Number: 80000002 LS Checksum: 0x51E2 Length: 32 Network Mask: 255.255.255.
IP Routing Commands 4 The following shows output when using the database-summary keyword. Console#show ip ospf database database-summary Area ID (10.1.0.
4 Command Line Interface The following shows output when using the external keyword. Console#show ip ospf database external OSPF Router with id(192.168.5.1) (Autonomous system 5) Displaying AS External Link States LS age: 433 Options: (No TOS-capability) LS Type: AS External Link Link State ID: 10.1.1.253 (External Network Number) Advertising Router: 10.1.2.254 LS Sequence Number: 80000002 LS Checksum: 0x51E2 Length: 32 Network Mask: 255.255.0.
4 IP Routing Commands The following shows output when using the network keyword. Console#show ip ospf database network OSPF Router with id(10.1.1.253) Displaying Net Link States(Area 10.1.0.0) Link State Data Network (Type 2) ------------------------------LS age: 433 Options: Support External routing capability LS Type: Network Links Link State ID: 10.1.1.252 (IP interface address of the Designated Router) Advertising Router: 10.1.1.
4 Command Line Interface The following shows output when using the router keyword. Console#show ip ospf database router OSPF Router with id(10.1.1.253) Displaying Router Link States(Area 10.1.0.0) Link State Data Router (Type 1) ------------------------------LS age: 233 Options: Support External routing capability LS Type: Router Links Link State ID: 10.1.1.252 (Originating Router's Router ID) Advertising Router: 10.1.1.
IP Routing Commands 4 Table 4-97 show ip ospf router - display description (Continued) Field Description Number of TOS metrics Type of Service metric – This router only supports TOS 0 (or normal service) Metrics Cost of the link The following shows output when using the summary keyword. Console#show ip ospf database summary OSPF Router with id(10.1.1.253) Displaying Summary Net Link States(Area 10.1.0.
4 Command Line Interface show ip ospf interface This command displays summary information for OSPF interfaces. Syntax show ip ospf interface [vlan vlan-id] vlan-id - VLAN ID (Range: 1-4094) Command Mode Privileged Exec Example Console#show ip ospf interface vlan 1 Vlan 1 is up Interface Address 10.1.1.253, Mask 255.255.255.0, Area 10.1.0.0 Router ID 10.1.1.253, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State BDR, Priority 1 Designated Router id 10.1.1.252, Interface address 10.1.1.
IP Routing Commands 4 show ip ospf neighbor This command displays information about neighboring routers on each interface within an OSPF area. Syntax show ip ospf neighbor Command Mode Privileged Exec Example Console#show ip ospf neighbor ID Pri State Address --------------- ------ ---------------- --------------10.1.1.252 1 FULL/DR 10.1.1.
4 Command Line Interface show ip ospf summary-address This command displays all summary address information. Syntax show ip ospf summary-address Command Mode Privileged Exec Example This example shows a summary address and associated network mask. Console#show ip ospf summary-address 10.1.0.0/255.255.0.0 Console# Related Commands summary-address (4-272) show ip ospf virtual-links This command displays detailed information about virtual links.
Multicast Routing Commands 4 Multicast Routing Commands This router uses IGMP snooping and query to determine the ports connected to downstream multicast hosts, and to propagate this information back up through the multicast tree to ensure that requested services are forwarded through each intermediate node between the multicast server and its hosts, and also to filter traffic from all of the other interfaces that do not require these services.
4 Command Line Interface Default Setting No static multicast router ports are configured. Command Mode Global Configuration Command Usage Depending on your network connections, IGMP snooping may not always be able to locate the IGMP querier. Therefore, if the IGMP querier is a known multicast router/switch connected over the network to an interface (port or trunk) on your router, you can manually configure that interface to join all the current multicast groups.
Multicast Routing Commands 4 General Multicast Routing Commands Table 4-104 General Multicast Routing Commands Command Function Mode ip multicast-routing Enables IP multicast routing GC Page 4-299 show ip mroute Shows the IP multicast routing table PE 4-299 ip multicast-routing This command enables IP multicast routing. Use the no form to disable IP multicast routing.
4 Command Line Interface Command Usage This command displays information for multicast routing. If no optional parameters are selected, detailed information for each entry in the multicast address table is displayed. If you select a multicast group and source pair, detailed information is displayed only for the specified entry. If the summary option is selected, an abbreviated list of information for each entry is displayed on a single line.
Multicast Routing Commands 4 DVMRP Multicast Routing Commands Table 4-106 DVMRP Multicast Routing Commands Command Function Mode router dvmrp Enables DVMRP and enters router configuration mode GC Page 4-301 probe-interval Sets the interval for sending neighbor probe messages RC 4-302 nbr-timeout Sets the delay before declaring an attached neighbor router down RC 4-303 report-interval Sets the interval for propagating the complete set of routing RC tables to other neighbor routers 4-303 f
4 Command Line Interface Example Console(config)#router dvmrp Console(config-router)#end Console#show router dvmrp Admin Status Probe Interval Nbr expire Minimum Flash Update Interval prune lifetime route report Default Gateway Metric of Default Gateway Console# : : : : : : : : enable 10 35 5 7200 60 0.0.0.
Multicast Routing Commands 4 nbr-timeout This command sets the interval to wait for messages from a DVMRP neighbor before declaring it dead. Use the no form to restore the default value. Syntax nbr-timeout seconds no nbr-timeout seconds - Interval before declaring a neighbor dead. (Range: 1-65535) Default Setting 35 seconds Command Mode Router Configuration Command Usage This command is used for timing out routes, and for setting the children and leaf flags.
4 Command Line Interface flash-update-interval This command specifies how often to send trigger updates, which reflect changes in the network topology. Use the no form to restore the default value. Syntax flash-update-interval seconds no flash-update-interval seconds - Interval between sending flash updates when network topology changes have occurred.
Multicast Routing Commands 4 default-gateway This command specifies the default DVMRP gateway for IP multicast traffic. Use the no form to remove the default gateway. Syntax default-gateway ip-address no default-gateway ip-address - IP address of the default DVMRP gateway. Default Setting None Command Mode Router Configuration Command Usage • The specified interface advertises itself as a default route to neighboring DVMRP routers. It advertises the default route out through its other interfaces.
4 Command Line Interface Command Usage To fully enable DVMRP, you need to enable multicast routing globally for the router with the ip multicast-routing command (page 4-299), enable DVMRP globally for the router with the router dvmrp command (page 4-301), and also enable DVMRP for each interface that will participate in multicast routing with the ip dvmrp command.
Multicast Routing Commands 4 clear ip dvmrp route This command clears all dynamic routes learned by DVMRP. Command Mode Privileged Exec Example As shown below, this command clears everything from the route table except for the default route. Console#clear ip dvmrp route clear all ip dvmrp route Console#show ip dvmrp route Source Mask Upstream_nbr Interface Metric UpTime Expire --------------- --------------- --------------- --------- ------ ------ -----10.1.0.0 255.255.255.0 10.1.0.
4 Command Line Interface show ip dvmrp route This command displays all entries in the DVMRP routing table. Command Mode Normal Exec, Privileged Exec Example DMVRP routes are shown in the following example: Console#show ip dvmrp route Source Mask Upstream_nbr Interface Metric UpTime Expire --------------- --------------- --------------- --------- ------ ------ -----10.1.0.0 255.255.255.0 10.1.0.253 vlan1 1 84438 0 10.1.1.0 255.255.255.0 10.1.1.253 vlan2 1 84987 0 10.1.8.0 255.255.255.0 10.1.0.
Multicast Routing Commands 4 show ip dvmrp neighbor This command displays all of the DVMRP neighbor routers. Command Mode Normal Exec, Privileged Exec Example Console#show ip dvmrp neighbor Address Interface Uptime Expire Capabilities ---------------- --------------- -------- -------- ------------10.1.0.
4 Command Line Interface PIM-DM Multicast Routing Commands Table 4-109 PIM-DM Multicast Routing Commands Command Function Mode router pim Enables PIM globally for the router GC Page 4-310 ip pim dense-mode Enables PIM on the specified interface IC 4-311 ip pim hello-interval Sets the interval between sending PIM hello messages IC 4-312 ip pim hello-holdtime Sets the time to wait for hello messages from a neighboring IC PIM router before declaring it dead 4-312 ip pim trigger-hello-interv
Multicast Routing Commands 4 ip pim dense-mode This command enables PIM-DM on the specified interface. Use the no form to disable PIM-DM on this interface.
4 Command Line Interface ip pim hello-interval This command configures the frequency at which PIM hello messages are transmitted. Use the no form to restore the default value. Syntax ip pim hello-interval seconds no pim hello-interval seconds - Interval between sending PIM hello messages.
Multicast Routing Commands 4 ip pim trigger-hello-interval This command configures the maximum time before transmitting a triggered PIM Hello message after the router is rebooted or PIM is enabled on an interface. Use the no form to restore the default value. Syntax ip pim triggerr-hello-interval seconds no ip pim triggerr-hello-interval seconds - The maximum time before sending a triggered PIM Hello message.
4 Command Line Interface Command Usage The multicast interface that first receives a multicast stream from a particular source forwards this traffic to all other PIM interfaces on the router. If there are no requesting groups on that interface, the leaf node sends a prune message upstream and enters a prune state for this multicast stream. The prune state is maintained until the join-prune-holdtime timer expires or a graft message is received for the forwarding entry.
Multicast Routing Commands 4 Default Setting 2 Command Mode Interface Configuration (VLAN) Example Console(config-if)#ip pim max-graft-retries 5 Console(config-if)# show router pim This command displays the global PIM configuration settings. Command Mode Normal Exec, Privileged Exec Example Console#show router pim Admin Status: Enabled Console# show ip pim interface This command displays information about interfaces configured for PIM.
4 Command Line Interface show ip pim neighbor This command displays information about PIM neighbors. Syntax show ip pim neighbor [ip-address] ip-address - IP address of a PIM neighbor. Default Setting Displays information for all known PIM neighbors. Command Mode Normal Exec, Privileged Exec Example Console#show ip pim neighbor Address VLAN Interface Uptime Expire Mode --------------- ---------------- -------- -------- ------10.1.0.
Router Redundancy Commands 4 Virtual Router Redundancy Protocol Commands To configure VRRP, select an interface on one router in the group to serve as the master virtual router. This physical interface is used as the virtual address for the router group. Now set the same virtual address and a priority on the backup routers, and configure an authentication string. You can also enable the preempt feature which allows a router to take over as the master router when it comes on line.
4 Command Line Interface Command Usage • The interfaces of all routers participating in a virtual router group must be within the same IP subnet. • The IP address assigned to the virtual router must already be configured on the router that will be the Owner. In other words, the IP address specified in this command must already exist on one, and only one, router in the virtual router group, and the network mask for the virtual router address is derived from the Owner.
Router Redundancy Commands 4 • When a VRRP packet is received from another router in the group, its authentication key is compared to the string configured on this router. If the keys match, the message is accepted. Otherwise, the packet is discarded. • Plain text authentication does not provide any real security. It is supported only to prevent a misconfigured router from participating in VRRP.
4 Command Line Interface vrrp timers advertise This command sets the interval at which the master virtual router sends advertisements communicating its state as the master. Use the no form to restore the default interval. Syntax vrrp group timers advertise interval no vrrp group timers advertise • group - Identifies the VRRP group. (Range: 1-255) • interval - Advertisement interval for the master virtual router.
Router Redundancy Commands 4 Default Setting • Preempt: Enabled • Delay: 0 seconds Command Mode Interface (VLAN) Command Usage • If preempt is enabled, and this backup router has a priority higher than the current acting master, it will take over as the new master. However, note that if the original master (i.e., the owner of the VRRP IP address) comes back on line, it will always resume control as the master.
4 Command Line Interface Example This example displays the full listing of status information for all groups. Console#show vrrp Vlan 1 - Group 1, state Virtual IP address Virtual MAC address Advertisement interval Preemption Min delay Priority Authentication Authentication key Master Router Master priority Master Advertisement interval Master down interval Console# Master 192.168.1.6 00-00-5E-00-01-01 5 sec enabled 10 sec 1 SimpleText bluebird 192.168.1.
Router Redundancy Commands 4 Table 4-114 show vrrp brief - display description Field Description Interface VLAN interface Grp VRRP group State VRRP role of this interface (master or backup) Virtual addr Virtual address that identifies this VRRP group Int Interval at which the master virtual router advertises its role as the master Pre Shows whether or not a higher priority router can preempt the current acting master Prio Priority of this router show vrrp interface This command displays st
4 Command Line Interface show vrrp router counters This command displays counters for errors found in VRRP protocol packets. Command Mode Privileged Exec Example Note that unknown errors indicate VRRP packets received with an unknown or unsupported version number.
Router Redundancy Commands 4 clear vrrp router counters This command clears VRRP system statistics. Command Mode Privileged Exec Example Console#clear vrrp router counters Console# clear vrrp interface counters This command clears VRRP system statistics for the specified group and interface. clear vrrp group interface interface counters • group - Identifies a VRRP group. (Range: 1-255) • interface - Identifier of configured VLAN interface.
4 4-326 Command Line Interface
Appendix A: Software Specifications Software Features Authentication Local, RADIUS, TACACS+, Port (802.
A Software Specifications Quality of Service DiffServ supports class maps, policy maps, and service policies Multicast Filtering IGMP Snooping (Layer 2) IGMP (Layer 3) Multicast Routing DVMRP, PIM-DM IP Routing ARP, Proxy ARP Static routes RIP, RIPv2 and OSPFv2 dynamic routing VRRP (Virtual Router Redundancy Protocol) Additional Features BOOTP client CIDR (Classless Inter-Domain Routing) SNTP (Simple Network Time Protocol) SNMP (Simple Network Management Protocol) RMON (Remote Monitoring, groups 1,2,3,9)
Management Information Bases A IEEE 802.3-2002 Ethernet, Fast Ethernet, Gigabit Ethernet Link Aggregation Control Protocol (LACP) Full-duplex flow control (ISO/IEC 8802-3) IEEE 802.
A Software Specifications Port Access Entity MIB (IEEE 802.
Appendix B: Troubleshooting Problems Accessing the Management Interface Table B-1 Troubleshooting Chart Symptom Action Cannot connect using Telnet, • Be sure the switch is powered up. web browser, or SNMP • Check network cabling between the management station and the switch. software • Check that you have a valid network connection to the switch and that the port you are using has not been disabled.
B Troubleshooting Using System Logs If a fault does occur, refer to the Installation Guide to ensure that the problem you encountered is actually caused by the switch. If the problem appears to be caused by the switch, follow these steps: 1. Enable logging. 2. Set the error messages reported to include all categories. 3. Designate the SNMP host that is to receive the error messages. 4. Repeat the sequence of commands or other actions that lead up to the error. 5.
Glossary Access Control List (ACL) ACLs can limit network traffic and restrict access to certain users or devices by checking each packet for certain IP or MAC (i.e., Layer 2) information. Address Resolution Protocol (ARP) ARP converts between IP addresses and MAC (i.e., hardware) addresses. ARP is used to locate the MAC address corresponding to a given IP address.
Glossary Distance Vector Multicast Routing Protocol (DVMRP) A distance-vector-style routing protocol used for routing multicast datagrams through the Internet. DVMRP combines many of the features of RIP with Reverse Path Forwarding (RPF). Dynamic Host Control Protocol (DHCP) Provides a framework for passing configuration information to hosts on a TCP/IP network.
Glossary IEEE 802.1Q VLAN Tagging—Defines Ethernet frame tags which carry VLAN information. It allows switches to assign endstations to different virtual LANs, and defines a standard way for VLANs to communicate across switched networks. IEEE 802.1p An IEEE standard for providing quality of service (QoS) in Ethernet networks. The standard uses packet tags that define up to eight traffic classes and allows switches to transmit packets based on the tagged priority value. IEEE 802.
Glossary In-Band Management Management of the network from a station attached directly to the network. IP Multicast Filtering A process whereby this switch can pass multicast traffic along to participating hosts. IP Precedence The Type of Service (ToS) octet in the IPv4 header includes three precedence bits defining eight different priority levels ranging from highest priority for network control packets to lowest priority for routine traffic.
Glossary Network Time Protocol (NTP) NTP provides the mechanisms to synchronize time across the network. The time servers operate in a hierarchical-master-slave configuration in order to synchronize local clocks within the subnet and to national time standards via wire or radio. Open Shortest Path First (OSPF) OSPF is a link-state routing protocol that functions better over a larger network such as the Internet, as opposed to distance-vector routing protocols such as RIP.
Glossary Dense Mode is designed for networks where the probability of a multicast client is high and frequent flooding of multicast traffic can be justified. Remote Authentication Dial-in User Service (RADIUS) RADIUS is a logon authentication protocol that uses software running on a central server to control access to RADIUS-compliant devices on the network. Remote Monitoring (RMON) RMON provides comprehensive network monitoring capabilities.
Glossary Telnet Defines a remote communication facility for interfacing to a terminal device over TCP/IP. Terminal Access Controller Access Control System Plus (TACACS+) TACACS+ is a logon authentication protocol that uses software running on a central server to control access to TACACS-compliant devices on the network. Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol.
Glossary Glossary-8
Index Numerics D 802.
Index Dynamic Host Configuration Protocol See DHCP E edge port, STA 3-126, 3-128, 4-181 event logging 4-43 F firmware displaying version 3-13, 4-62 upgrading 3-21, 4-64 G GARP VLAN Registration Protocol See GVRP gateway, default 3-17, 3-208, 4-245 GVRP global setting 3-138, 4-202 interface configuration 3-144, 4-203 H hardware version, displaying 3-13, 4-62 HTTPS 3-58, 4-32 HTTPS, secure server 3-58, 4-32 I IEEE 802.1D 3-116, 4-171 IEEE 802.1s 4-171 IEEE 802.1w 3-116, 4-171 IEEE 802.
Index MSTP 4-171 global settings 3-129, 4-170 interface settings 3-127, 4-170 multicast filtering 3-169, 4-228 multicast groups 3-175, 3-181, 4-230 displaying 3-181, 4-230 static 3-175, 4-229, 4-230 multicast routing 3-261, 4-297 description 3-261 DVMRP 3-265, 4-301 enabling 3-261, 4-299 general commands 4-299 global settings 3-261, 4-299 PIM-DM 3-272, 4-310 routing table 3-262, 4-299 multicast services configuring 3-176, 4-229 displaying 3-175, 4-230 multicast, static router port 3-174, 4-235, 4-297 O OSP
Index specifying interfaces 3-228, 4-258 statistics 3-232, 4-265 router redundancy protocols 3-196, 4-316 VRRP 3-197, 4-317 routing table, displaying 3-224, 4-253, 4-254 RSTP 3-116, 4-171 global configuration 3-117, 4-171 S secure shell 3-60, 4-34 Secure Shell configuration 3-60, 4-37, 4-38 serial port configuring 4-11 SNMP 3-37 community string 3-39, 4-109 enabling traps 3-40, 4-112 trap manager 3-40, 4-110 software displaying version 3-13, 4-62 downloading 3-21, 4-64 Spanning Tree Protocol See STA specif
Index private 3-146, 4-197 protocol 3-147, 4-198 VRRP 3-197, 4-317 authentication 3-199, 4-318 configuration settings 3-197, 4-317 group statistics 3-203, 4-321 preemption 3-198, 3-199, 4-320 priority 3-198, 3-199, 4-319 protocol message statistics 3-202, 4-324 timers 3-199, 4-320 virtual address 3-197, 3-199, 4-317 W Web interface access requirements 3-1 configuration buttons 3-3 home page 3-2 menu list 3-4 panel display 3-3 Index-5
Index Index-6
ES3628C E032005-R01 149100005100H
