CheetahSwitch Workgroup-2027 Quick Installation Guide ES2027 E0298-R03 150185-101
Copyright © 1998 by Accton Technology Corporation. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation. CheetahSwitch Workgroup-2027 Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability, quality, or fitness for any particular purpose. The information in this document is subject to change without notice.
CheetahSwitch Workgroup-2027 Contents Quick Installation Guide Introduction Introduction 1 Package Contents 1 Description of Hardware 1 Mounting the Switch Stacking Switches on a Flat Surface Mounting Switches in a Rack 2 2 2 Connecting the Switch System Making a Connection via an MDI-X Station Port Making a Connection via the MDI Daisy-Chain Port Making a Connection via the AUI Port Connecting to an Uplink Module 2 3 3 4 4 Powering on the Switch 5 Verifying Port Status 6 Verifying System O
CheetahSwitch Workgroup-2027 Mounting the Switch This switch can be placed directly on your desktop, or mounted in a rack. Before you start installing the switch, make sure you can provide the right operating environment, including power requirements, sufficient physical space, and proximity to other network devices that are to be connected. Verify the following installation requirements: Power requirements: 100 to 240 VAC (± 10%) at 50 to 60 Hz (± 3Hz).
CheetahSwitch Workgroup-2027 Quick Installation Guide Restrictions on Cascade Length - Because the CheetahSwitch breaks up the path for connected devices into separate collision domains, it has no restrictions on cascade length. Therefore, when cascading devices other than this switch, do not include it or any connected cabling in your calculations for cascade length. The 100BASE-TX Uplink Module can set the transmission mode to full or half duplex via auto-negotiation.
CheetahSwitch Workgroup-2027 Quick Installation Guide Verifying Port Status Configuring the Switch Check each connection by viewing the port status indicators shown in the following figure and table. The transmission mode for all ports must be set to the same mode used by the connected device. Ports 1 - 25 and the 100BASE-FX Uplink Module must be manually configured; but the system can use auto-negotiation to determine the transmission mode for the 100BASE-TX Uplink Module.
CheetahSwitch Workgroup-2027 If this is your first time to log into the configuration program, then the default password will still be null. Just enter a carriage return for the "Login" and "Password" fields to open the Main Menu as shown below. ACCTON CheetahSwitch Workgroup-2027 V1.00 05-04-97 Main Menu --------Port Configuration ... Password Configuration ... Restart System Factory Reset Exit Configure port setting. to confirm.
CheetahSwitch Workgroup-2027 Filtering Rate Forwarding Rate Product Specifications Base Unit Access Method Standards Conformance Communication Rate Communication Mode Media Supported Number of Ports Indicator Panel Dimensions Weight Input Power Power Consumption Heat Dissipation Temperature Humidity Certification Emissions Immunity Safety Uplink Modules 100BASE-TX Access Method Standards Conformance Communication Rate Communication Mode Media Supported Number of Ports Indicator Panel 100BASE-FX Access Met
CheetahSwitch Workgroup-2027 Quick Installation Guide Port and Cable Assignments You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or greater for 10 Mbps connections, and Category 5 for 100 Mbps connections. RJ-45 Port Description Class A (Canada Department of Communications) RJ-45 station ports (MDI-X) can be attached to any devices which use a standard network interface (e.g., a workstation, server, bridge or router). Similar networking devices (e.g.
CheetahSwitch Workgroup-2027 Quick Installation Guide Wichtige Sicherheitshinweise (Germany) 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5.
