User's Manual
Table Of Contents
- Chapter 1: Introduction 1-1
- Chapter 1: Introduction
- Chapter 2: Hardware Installation
- Chapter 3: Network Configuration
- Chapter 4: Initial Configuration
- Chapter 5: System Configuration
- Chapter 6: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Appendix A: Troubleshooting
- Appendix B: Cables and Pinouts
- Appendix C: Specifications
- Glossary
- Index
SNMP
5-39
5
Trap Configuration – Allows selection of specific SNMP notifications to send. The
following items are available:
• sysSystemUp - The access point is up and running.
• sysSystemDown - The access point is about to shutdown and reboot.
• sysRadiusServerChanged - The access point has changed from the primary
RADIUS server to the secondary, or from the secondary to the primary.
• sysConfigFileVersionChanged - The access point’s configuration file has been
changed.
• dot11StationAssociation - A client station has successfully associated with the
access point.
• dot11StationReAssociation - A client station has successfully re-associated with
the access point.
• dot11StationAuthentication - A client station has been successfully authenticated.
• dot11StationRequestFail - A client station has failed association, re-association, or
authentication.
• dot11InterfaceBFail - The 802.11b interface has failed.
• dot1xMacAddrAuthSuccess - A client station has successfully authenticated its
MAC address with the RADIUS server.
• dot1xMacAddrAuthFail - A client station has failed MAC address authentication
with the RADIUS server.
• dot1xAuthNotInitiated - A client station did not initiate 802.1X authentication.
• dot1xAuthSuccess - A 802.1X client station has been successfully authenticated
by the RADIUS server.
• dot1xAuthFail - A 802.1X client station has failed RADIUS authentication.
• dot1xSuppAuthenticated - A supplicant station has been successfully
authenticated by the RADIUS server
• localMacAddrAuthSuccess - A client station has successfully authenticated its
MAC address with the local database on the access point.
• localMacAddrAuthFail - A client station has failed authentication with the local MAC
address database on the access point.
• iappStationRoamedFrom - A client station has roamed from another access point
(identified by its IP address).
• iappStationRoamedTo - A client station has roamed to another access point
(identified by its IP address).
• iappContextDataSent - A client station’s Context Data has been sent to another
access point with which the station has associated.
• sntpServerFail - The access point has failed to set the time from the configured
SNTP server.
• wirelessExternalAntenna - An external antenna has been enabled.
• dot11WirelessStationDeauthenticate - A client station has de-authenticated from
the network.
• dot11StationDisassociate - A client station no longer associates with the network.