User's Manual
Table Of Contents
- Chapter 1: Introduction 1-1
- Chapter 1: Introduction
- Chapter 2: Hardware Installation
- Chapter 3: Network Configuration
- Chapter 4: Initial Configuration
- Chapter 5: System Configuration
- Chapter 6: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Appendix A: Troubleshooting
- Appendix B: Cables and Pinouts
- Appendix C: Specifications
- Glossary
- Index
System Configuration
5-2
5
Advanced Configuration
The Advanced Configuration pages include the following options.
Table 5-2. Menu
Menu Description Page
System Configures basic administrative and client access 5-3
Identification Specifies the host name 5-3
TCP / IP Settings Configures the IP address, subnet mask, gateway, and domain
name servers
5-5
RADIUS Configures the RADIUS server for wireless client authentication
and accounting
5-7
SSH Settings Configures Secure Shell management access 5-11
Authentication Configures 802.1X client authentication, with an option for MAC
address authentication
5-12
Filter Control Filters communications between wireless clients, access to the
management interface from wireless clients, and traffic matching
specific Ethernet protocol types
5-17
VLAN Enables VLAN support and sets the management VLAN ID 5-19
WDS Settings Configures bridge or repeater modes for each radio interface and
sets spanning tree parameters
5-21
AP Management Configures access to management interfaces 5-27
Administration Configures user name and password for management
access;
upgrades software from local file, FTP or TFTP server;
resets
configuration settings to factory defaults; and resets the access
point
5-28
System Log Controls logging of error messages; sets the system clock via
SNTP server or manual configuration
5-32
SNMP Configures SNMP settings 5-36
SNMP Controls access to this access point from management stations
using SNMP, as well as the hosts that will receive trap messages
5-36
SNMP Trap Filters Defines trap filters for SNMPv3 users 5-44
SNMP Targets Specifies SNMPv3 users that will receive trap messages 5-46
Radio Interface G Configures the IEEE 802.11g interface 5-48
Radio Settings Configures common radio signal parameters and other settings for
each VAP interface
5-48
Security Enables each VAP interface, sets the SSID, and configures
wireless security
5-63
Status Displays information about the access point and wireless clients 5-82
AP Status Displays configuration settings for the basic system and the
wireless interface
5-82