User's Manual
Table Of Contents
- Chapter 1: Introduction 1-1
- Chapter 1: Introduction
- Chapter 2: Hardware Installation
- Chapter 3: Network Configuration
- Chapter 4: Initial Configuration
- Chapter 5: System Configuration
- Chapter 6: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Appendix A: Troubleshooting
- Appendix B: Cables and Pinouts
- Appendix C: Specifications
- Glossary
- Index
General Commands
6-7
6
The access mode shown in the following tables is indicated by these abbreviations:
Exec (Executive Mode), GC (Global Configuration), IC-E (Interface-Ethernet
Configuration), IC-W (Interface-Wireless Configuration), and IC-W-VAP
(Interface-Wireless VAP Configuration).
General Commands
SNMP Configures community access strings and trap managers 6-40
Flash/File Manages code image or access point configuration files 6-55
RADIUS Configures the RADIUS client used with 802.1X authentication 6-58
802.1X Authentication Configures 802.1X authentication 6-65
MAC Address
Authentication
Configures MAC address authentication 6-70
Filtering Filters communications between wireless clients, controls access to the
management interface from wireless clients, and filters traffic using
specific Ethernet protocol types
6-73
WDS Bridge Configures WDS forwarding table settings 6-77
Spanning Tree Configures spanning tree parameters 6-83
Ethernet Interface Configures connection parameters for the Ethernet interface 6-88
Wireless Interface Configures radio interface settings 6-93
Wireless Security Configures radio interface security and encryption settings 6-109
Rogue AP Detection Configures settings for the detection of rogue access points in the
network
6-109
Link Integrity Configures a link check to a host device on the wired network 6-123
IAPP Enables roaming between multi-vendor access points 6-127
VLANs Configures VLAN membership 6-128
WMM Configures WMM quality of service parameters 6-130
Table 6-3. General Commands
Command Function Mode Page
configure Activates global configuration mode Exec 6-8
end Returns to previous configuration mode GC, IC 6-8
exit Returns to the previous configuration mode, or exits the CLI any 6-8
ping Sends ICMP echo request packets to another node on the
network
Exec 6-9
reset Restarts the system Exec 6-10
show history Shows the command history buffer Exec 6-10
show line Shows the configuration settings for the console port Exec 6-11
Table 6-2. Command Groups
Command Group Description Page