User's Manual
Table Of Contents
- Chapter 1: Introduction 1-1
- Chapter 1: Introduction
- Chapter 2: Hardware Installation
- Chapter 3: Network Configuration
- Chapter 4: Initial Configuration
- Chapter 5: System Configuration
- Chapter 6: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- General Commands
- System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server engine-id
- snmp-server user
- snmp-server targets
- snmp-server filter
- snmp-server filter-assignments
- show snmp groups
- show snmp users
- show snmp group-assignments
- show snmp target
- show snmp filter
- show snmp filter-assignments
- show snmp
- Flash/File Commands
- RADIUS Client
- 802.1X Authentication
- MAC Address Authentication
- Filtering Commands
- WDS Bridge Commands
- Spanning Tree Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- speed
- multicast-data-rate
- channel
- transmit-power
- radio-mode
- preamble
- antenna control
- antenna id
- antenna location
- beacon-interval
- dtim-period
- fragmentation-length
- rts-threshold
- super-g
- description
- ssid
- closed-system
- max-association
- assoc-timeout-interval
- auth-timeout-value
- shutdown
- show interface wireless
- show station
- Rogue AP Detection Commands
- Wireless Security Commands
- Link Integrity Commands
- IAPP Commands
- VLAN Commands
- WMM Commands
- Appendix A: Troubleshooting
- Appendix B: Cables and Pinouts
- Appendix C: Specifications
- Glossary
- Index
Radio Interface
5-69
5
Enable – Enables radio communications on the VAP interface. (Default: Disabled)
Note: You must first enable VAP interface 0 before you can enable other VAP
interfaces.
SSID – The name of the basic service set provided by a VAP interface. Clients that
want to connect to the network through the access point must set their SSID to the
same as that of an access point VAP interface. (Default: SMC_G # (0 to 7); Range:
1-32 characters)
Wired Equivalent Privacy (WEP)
WEP provides a basic level of security, preventing unauthorized access to the
network, and encrypting data transmitted between wireless clients and the access
point. WEP uses static shared keys (fixed-length hexadecimal or alphanumeric
strings) that are manually distributed to all clients that want to use the network.
WEP is the security protocol initially specified in the IEEE 802.11 standard for
wireless communications. Unfortunately, WEP has been found to be seriously
flawed and cannot be recommended for a high level of network security. For more
robust wireless security, the access point provides Wi-Fi Protected Access (WPA)
for improved data encryption and user authentication.
Setting up shared keys enables the basic IEEE 802.11 Wired Equivalent Privacy
(WEP) on the access point to prevent unauthorized access to the network.
If you choose to use WEP shared keys instead of an open system, be sure to define
at least one static WEP key for user authentication and data encryption. Also, be
sure that the WEP shared keys are the same for each client in the wireless network.
Note that all clients share the same keys, which are used for user authentication and
data encryption. Up to four keys can be specified. These four keys are used for all
VAP interfaces on the same radio.
To set up WEP shared keys, click Radio Settings.
Key Type – Select the preferred method of entering WEP encryption keys on the
access point and enter up to four keys:
• Hexadecimal: Enter keys as 10 hexadecimal digits (0-9 and A-F) for 64 bit keys, 26
hexadecimal digits for 128 bit keys, or 32 hexadecimal digits for 152 bit keys. This
is the default setting.