User's Manual

ManualsBrandsAccton Technology ManualsElectronics802.11a outdoor CPE (Client)

SU-A-MB-12-EZ CPE for BreezeACCESS VL Quick Installation Guide

P/N: October 2006

This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the

BreezeAccess VL System Manual.

ODU CPE Package Content

Check that the package contains:

• ODU CPE Outdoor Unit (with integral antenna)

• A wall and pole mounting kit

• Mains power cord (this item is packed separately from the IDU package).

• This Quick Installation Guide

Tilt Accessory Kit (Optional)

Ordered separately.

Additional Equipment and Tools Required for Installation

• Ethernet cable for connecting to the user’s data equipment (crossed for connecting to a hub/switch, straight for connecting

to a PC)

• Indoor-to-outdoor Category 5E Ethernet cable. Use only Category 5E cables approved by the supplier. The length of the

Indoor-to-Outdoor cable should not exceed 90 meters. The length of the Indoor-to-Outdoor cable, together with the length

of the Ethernet cable connecting the CPE-IDU-1D to the data equipment, should not exceed 100 meters.

• Two shielded RJ-45 connectors

• Grounding cable with an appropriate termination.

• Mains plug adapter or termination plug (if the power plug on the supplied AC power cord does not fit local power outlets).

• Portable PC/Notebook and a straight Ethernet cable for configuring parameters using Telnet. TFTP server SW is required

for downloading SW versions. OR portable PC/Notebook or Pocket PC/PDA and a straight Ethernet cable for configuring

parameters using a web browser

• Installation tools and materials, including appropriate means (e.g. a pole) for installing the outdoor unit (and antenna where

applicable) and for sealing any outdoor connectors.

• To connect directly to the ODU for configuration/performance monitoring: A special Y-cable and a Notebook or PDA with

web browser.

• Optional SU Alignment Unit (SAU) for easy alignment of the antenna.

WARNING:

ONLY experienced installation professionals who are familiar with local building and safety codes and,

wherever applicable, are licensed by the appropriate government regulatory authorities should install outdoor

units and antennas. Failure to do so may void the product warranty and may expose the end user or Service

Provider to legal and financial liabilities. The manufacturer and its resellers or distributors are not liable for

injury, damage or regulation violations associated with the installation of outdoor units or antennas.

Equipment Location Guidelines

The antenna should provide a direct, or near line of sight, with the Base Station antenna. The higher the placement of the

antenna, the better the achievable link quality. The location of the ODU should enable easy access to the unit for installation and

testing.

ODU Installation

Mount the ODU unit using the clamp, band and screws supplied with the unit. The unit’s antenna is polarized vertically in the

direction of the RJ45 port. Install the unit with the connectors facing downwards as shown in the following image.

Summary of content (6 pages)

PAGE 1
SU-A-MB-12-EZ CPE for BreezeACCESS VL Quick Installation Guide This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the BreezeAccess VL System Manual. ODU CPE Package Content Check that the package contains: • ODU CPE Outdoor Unit (with integral antenna) • A wall and pole mounting kit • Mains power cord (this item is packed separately from the IDU package).
PAGE 2
ODU CPE for BreezeACCESS VL Quick Installation Guide 1. Thread the provided metal band through the adaptor bracket and use the screws provided with the mounting kit to attach the adaptor bracket to the unit. 2. 3. Connect a grounding cable between the Ground terminal of the ODU (marked Align the unit using the LED display. ) and a good ground connection. Preparing the IDU-ODU Cable Use a crimp tool for RJ-45 connectors to prepare the wires.
PAGE 3
ODU CPE for BreezeACCESS VL Quick Installation Guide 3. 4. 5. 6. 7. Connect the Ethernet cable to the ODU RJ-45 connector. Put the sealing cap back in its place to ensure protection against moisture. Make sure that the small protrusion on the side of the cap fits inside the hole on the connector’s protective body. Use appropriate sealing material to protect the connection against moisture and humidity.
PAGE 4
ODU CPE for BreezeACCESS VL Quick Installation Guide 8. Reset the unit to apply the changes. Aligning the Antenna 1. 2. 3. Point the antenna toward the general direction of the Base Station. Connect the SAU to the ODU (optional) and verify that the PWR (power) indication on the SAU is on. Verify that the unit is synchronized with a Base Station. If the SU is not synchronized with a Base Station, ensure that all parameters are configured properly.
PAGE 5
ODU CPE for BreezeACCESS VL Quick Installation Guide FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
ODU CPE for BreezeACCESS VL Quick Installation Guide R&TTE Compliance Statement This equipment complies with the appropriate essential requirements of Article 3 of the R&TTE Directive 1999/5/EC.