User's Manual
Table Of Contents
- Compliances
- About This Manual
- Table of Contents
- Chapter 1 - Product Description
- Chapter 2 - Hardware Installation
- 2.1 Hardware Description
- 2.2 Installation Requirements
- 2.3 Installation
- 2.3.1 Attaching the SU-ODU to the Mounting Plate
- 2.3.2 Attaching the Mounting Plate to the Wi· unit
- 2.3.3 Connecting the Wi· unit to the SU-ODU
- 2.3.4 Preparing the Power Cable
- 2.3.5 Pre-Configuration and Testing
- 2.3.6 Mounting the Wi· Unit
- 2.3.7 Connecting the Grounding Cables
- 2.3.8 Connecting to Power Source
- 2.4 Post Installation Configuration of the AP/SU-ODU
- Chapter 3 - Initial Configuration
- Chapter 4 - System Configuration
- 4.1 Introduction
- 4.2 Advanced Configuration
- 4.3 SNMP
- 4.4 Radio Interface
- 4.5 Status Information
- Chapter 5 - Command Line Interface
- 5.1 Using the Command Line Interface
- 5.2 Entering Commands
- 5.2.1 Keywords and Arguments
- 5.2.2 Minimum Abbreviation
- 5.2.3 Command Completion
- 5.2.4 Getting Help on Commands
- 5.2.5 Partial Keyword Lookup
- 5.2.6 Negating the Effect of Commands
- 5.2.7 Using Command History
- 5.2.8 Understanding Command Modes
- 5.2.9 Exec Commands
- 5.2.10 Configuration Commands
- 5.2.11 Command Line Processing
- 5.3 Command Groups
- 5.4 General Commands
- 5.5 System Management Commands
- 5.5.1 country
- 5.5.2 prompt
- 5.5.3 system name
- 5.5.4 username
- 5.5.5 password
- 5.5.6 ip ssh-server enable
- 5.5.7 ip ssh-server port
- 5.5.8 ip telnet-server enable
- 5.5.9 ip http port
- 5.5.10 ip http server
- 5.5.11 ip http session-timeout
- 5.5.12 ip https port
- 5.5.13 ip https server
- 5.5.14 APmgmtIP
- 5.5.15 APmgmtUI
- 5.5.16 show apmanagement
- 5.5.17 show system
- 5.5.18 show version
- 5.5.19 show config
- 5.5.20 show hardware
- 5.6 System Logging Commands
- 5.7 System Clock Commands
- 5.8 DHCP Relay Commands
- 5.9 SNMP Commands
- 5.9.1 snmp-server community
- 5.9.2 snmp-server contact
- 5.9.3 snmp-server location
- 5.9.4 snmp-server enable server
- 5.9.5 snmp-server host
- 5.9.6 snmp-server trap
- 5.9.7 snmp-server engine-id
- 5.9.8 snmp-server user
- 5.9.9 snmp-server targets
- 5.9.10 snmp-server filter
- 5.9.11 snmp-server filter-assignments
- 5.9.12 show snmp groups
- 5.9.13 show snmp users
- 5.9.14 show snmp group-assignments
- 5.9.15 show snmp target
- 5.9.16 show snmp filter
- 5.9.17 show snmp filter-assignments
- 5.9.18 show snmp
- 5.10 Flash/File Commands
- 5.11 RADIUS Client
- 5.12 802.1X Authentication
- 5.13 MAC Address Authentication
- 5.14 Filtering Commands
- 5.15 WDS Bridge Commands
- 5.16 Spanning Tree Commands
- 5.17 Ethernet Interface Commands
- 5.18 Wireless Interface Commands
- 5.18.1 interface wireless
- 5.18.2 vap
- 5.18.3 speed
- 5.18.4 multicast-data-rate
- 5.18.5 channel
- 5.18.6 transmit-power
- 5.18.7 radio-mode
- 5.18.8 preamble
- 5.18.9 antenna control
- 5.18.10 antenna id
- 5.18.11 antenna location
- 5.18.12 beacon-interval
- 5.18.13 dtim-period
- 5.18.14 fragmentation-length
- 5.18.15 rts-threshold
- 5.18.16 super-g
- 5.18.17 description
- 5.18.18 ssid
- 5.18.19 closed-system
- 5.18.20 max-association
- 5.18.21 assoc-timeout-interval
- 5.18.22 auth-timeout-value
- 5.18.23 shutdown
- 5.18.24 show interface wireless
- 5.18.25 show station
- 5.19 Rogue AP Detection Commands
- 5.20 Wireless Security Commands
- 5.21 Link Integrity Commands
- 5.22 IAPP Commands
- 5.23 VLAN Commands
- 5.24 WMM Commands
- Appendix A - Troubleshooting
48 Operation
Chapter 4 - System Configuration
4.2.3 RADIUS
Remote Authentication Dial-in User Service (RADIUS) is an authentication
protocol that uses software running on a central server to control access to
RADIUS-aware devices on the network. An authentication server contains a
database of user credentials for each user that requires access to the network.
A primary RADIUS server must be specified for the AP to implement IEEE 802.1X
network access control and WiFi Protected Access (WPA) wireless security. A
secondary RADIUS server may also be specified as a backup should the primary
server fail or become inaccessible.
In addition, the configured RADIUS server can also act as a RADIUS Accounting
server and receive user-session accounting information from the AP. RADIUS
Accounting can be used to provide valuable information on user activity in the
network.
NOTE
This manual assumes that you have already configured RADIUS server(s) to support the AP.
Configuration of RADIUS server software is beyond the scope of this manul, refer to the
documentation provided with the RADIUS server software.