User's Manual
Table Of Contents
- Compliances
- About This Manual
- Table of Contents
- Chapter 1 - Product Description
- Chapter 2 - Hardware Installation
- 2.1 Hardware Description
- 2.2 Installation Requirements
- 2.3 Installation
- 2.3.1 Attaching the SU-ODU to the Mounting Plate
- 2.3.2 Attaching the Mounting Plate to the Wi· unit
- 2.3.3 Connecting the Wi· unit to the SU-ODU
- 2.3.4 Preparing the Power Cable
- 2.3.5 Pre-Configuration and Testing
- 2.3.6 Mounting the Wi· Unit
- 2.3.7 Connecting the Grounding Cables
- 2.3.8 Connecting to Power Source
- 2.4 Post Installation Configuration of the AP/SU-ODU
- Chapter 3 - Initial Configuration
- Chapter 4 - System Configuration
- 4.1 Introduction
- 4.2 Advanced Configuration
- 4.3 SNMP
- 4.4 Radio Interface
- 4.5 Status Information
- Chapter 5 - Command Line Interface
- 5.1 Using the Command Line Interface
- 5.2 Entering Commands
- 5.2.1 Keywords and Arguments
- 5.2.2 Minimum Abbreviation
- 5.2.3 Command Completion
- 5.2.4 Getting Help on Commands
- 5.2.5 Partial Keyword Lookup
- 5.2.6 Negating the Effect of Commands
- 5.2.7 Using Command History
- 5.2.8 Understanding Command Modes
- 5.2.9 Exec Commands
- 5.2.10 Configuration Commands
- 5.2.11 Command Line Processing
- 5.3 Command Groups
- 5.4 General Commands
- 5.5 System Management Commands
- 5.5.1 country
- 5.5.2 prompt
- 5.5.3 system name
- 5.5.4 username
- 5.5.5 password
- 5.5.6 ip ssh-server enable
- 5.5.7 ip ssh-server port
- 5.5.8 ip telnet-server enable
- 5.5.9 ip http port
- 5.5.10 ip http server
- 5.5.11 ip http session-timeout
- 5.5.12 ip https port
- 5.5.13 ip https server
- 5.5.14 APmgmtIP
- 5.5.15 APmgmtUI
- 5.5.16 show apmanagement
- 5.5.17 show system
- 5.5.18 show version
- 5.5.19 show config
- 5.5.20 show hardware
- 5.6 System Logging Commands
- 5.7 System Clock Commands
- 5.8 DHCP Relay Commands
- 5.9 SNMP Commands
- 5.9.1 snmp-server community
- 5.9.2 snmp-server contact
- 5.9.3 snmp-server location
- 5.9.4 snmp-server enable server
- 5.9.5 snmp-server host
- 5.9.6 snmp-server trap
- 5.9.7 snmp-server engine-id
- 5.9.8 snmp-server user
- 5.9.9 snmp-server targets
- 5.9.10 snmp-server filter
- 5.9.11 snmp-server filter-assignments
- 5.9.12 show snmp groups
- 5.9.13 show snmp users
- 5.9.14 show snmp group-assignments
- 5.9.15 show snmp target
- 5.9.16 show snmp filter
- 5.9.17 show snmp filter-assignments
- 5.9.18 show snmp
- 5.10 Flash/File Commands
- 5.11 RADIUS Client
- 5.12 802.1X Authentication
- 5.13 MAC Address Authentication
- 5.14 Filtering Commands
- 5.15 WDS Bridge Commands
- 5.16 Spanning Tree Commands
- 5.17 Ethernet Interface Commands
- 5.18 Wireless Interface Commands
- 5.18.1 interface wireless
- 5.18.2 vap
- 5.18.3 speed
- 5.18.4 multicast-data-rate
- 5.18.5 channel
- 5.18.6 transmit-power
- 5.18.7 radio-mode
- 5.18.8 preamble
- 5.18.9 antenna control
- 5.18.10 antenna id
- 5.18.11 antenna location
- 5.18.12 beacon-interval
- 5.18.13 dtim-period
- 5.18.14 fragmentation-length
- 5.18.15 rts-threshold
- 5.18.16 super-g
- 5.18.17 description
- 5.18.18 ssid
- 5.18.19 closed-system
- 5.18.20 max-association
- 5.18.21 assoc-timeout-interval
- 5.18.22 auth-timeout-value
- 5.18.23 shutdown
- 5.18.24 show interface wireless
- 5.18.25 show station
- 5.19 Rogue AP Detection Commands
- 5.20 Wireless Security Commands
- 5.21 Link Integrity Commands
- 5.22 IAPP Commands
- 5.23 VLAN Commands
- 5.24 WMM Commands
- Appendix A - Troubleshooting
256 BreezeMAX Wi² and BreezeACCESS Wi² System Manual
Glossary
Shared Key A shared key can be used to authenticate each client attached
to a wireless network. Shared Key authentication must be used
along with the 802.11 Wireless Equivalent Privacy algorithm.
SNMP Simple Network Management Protocol: The application
protocol in the Internet suite of protocols which offers network
management services.
SNTP Simple Network Time Protocol: SNTP allows a device to set its
internal clock based on periodic updates from a Network Time
Protocol (NTP) server. Updates can be requested from a specific
NTP server, or can be received via broadcasts sent by NTP
servers.
SSID Service Set Identifier: An identifier that is attached to packets
sent over the wireless LAN and functions as a password for
joining a particular radio cell; i.e., Basic Service Set (BSS).
SU-ODU Subscriber Outdoor Unit
TFTP Trivial File Transfer Protocol: A TCP/IP protocol commonly
used for software downloads.
TKIP Temporal Key Integrity Protocol: A data encryption method
designed as a replacement for WEP. TKIP avoids the problems
of WEP static keys by dynamically changing data encryption
keys.
VAP Virtual Access Point: Virtual AP technology multiplies the
number of Access Points present within the RF footprint of a
single physical access device. With Virtual AP technology,
WLAN users within the device’s footprint can associate with
what appears to be different Wi²s and their associated network
services. All the services are delivered using a single radio
channel, enabling Virtual AP technology to optimize the use of
limited WLAN radio spectrum.
VLAN Virtual Local Area Network: A group of devices on one or more
LANs that are configured with the same VLAN ID so that they
can communicate as if they were attached to the same wire,
when in fact they are located on a number of different LAN
segments. Used also to create separation between different
user groups.