User's Manual
Table Of Contents
- Compliances
- About This Manual
- Table of Contents
- Chapter 1 - Product Description
- Chapter 2 - Hardware Installation
- 2.1 Hardware Description
- 2.2 Installation Requirements
- 2.3 Installation
- 2.3.1 Attaching the SU-ODU to the Mounting Plate
- 2.3.2 Attaching the Mounting Plate to the Wi· unit
- 2.3.3 Connecting the Wi· unit to the SU-ODU
- 2.3.4 Preparing the Power Cable
- 2.3.5 Pre-Configuration and Testing
- 2.3.6 Mounting the Wi· Unit
- 2.3.7 Connecting the Grounding Cables
- 2.3.8 Connecting to Power Source
- 2.4 Post Installation Configuration of the AP/SU-ODU
- Chapter 3 - Initial Configuration
- Chapter 4 - System Configuration
- 4.1 Introduction
- 4.2 Advanced Configuration
- 4.3 SNMP
- 4.4 Radio Interface
- 4.5 Status Information
- Chapter 5 - Command Line Interface
- 5.1 Using the Command Line Interface
- 5.2 Entering Commands
- 5.2.1 Keywords and Arguments
- 5.2.2 Minimum Abbreviation
- 5.2.3 Command Completion
- 5.2.4 Getting Help on Commands
- 5.2.5 Partial Keyword Lookup
- 5.2.6 Negating the Effect of Commands
- 5.2.7 Using Command History
- 5.2.8 Understanding Command Modes
- 5.2.9 Exec Commands
- 5.2.10 Configuration Commands
- 5.2.11 Command Line Processing
- 5.3 Command Groups
- 5.4 General Commands
- 5.5 System Management Commands
- 5.5.1 country
- 5.5.2 prompt
- 5.5.3 system name
- 5.5.4 username
- 5.5.5 password
- 5.5.6 ip ssh-server enable
- 5.5.7 ip ssh-server port
- 5.5.8 ip telnet-server enable
- 5.5.9 ip http port
- 5.5.10 ip http server
- 5.5.11 ip http session-timeout
- 5.5.12 ip https port
- 5.5.13 ip https server
- 5.5.14 APmgmtIP
- 5.5.15 APmgmtUI
- 5.5.16 show apmanagement
- 5.5.17 show system
- 5.5.18 show version
- 5.5.19 show config
- 5.5.20 show hardware
- 5.6 System Logging Commands
- 5.7 System Clock Commands
- 5.8 DHCP Relay Commands
- 5.9 SNMP Commands
- 5.9.1 snmp-server community
- 5.9.2 snmp-server contact
- 5.9.3 snmp-server location
- 5.9.4 snmp-server enable server
- 5.9.5 snmp-server host
- 5.9.6 snmp-server trap
- 5.9.7 snmp-server engine-id
- 5.9.8 snmp-server user
- 5.9.9 snmp-server targets
- 5.9.10 snmp-server filter
- 5.9.11 snmp-server filter-assignments
- 5.9.12 show snmp groups
- 5.9.13 show snmp users
- 5.9.14 show snmp group-assignments
- 5.9.15 show snmp target
- 5.9.16 show snmp filter
- 5.9.17 show snmp filter-assignments
- 5.9.18 show snmp
- 5.10 Flash/File Commands
- 5.11 RADIUS Client
- 5.12 802.1X Authentication
- 5.13 MAC Address Authentication
- 5.14 Filtering Commands
- 5.15 WDS Bridge Commands
- 5.16 Spanning Tree Commands
- 5.17 Ethernet Interface Commands
- 5.18 Wireless Interface Commands
- 5.18.1 interface wireless
- 5.18.2 vap
- 5.18.3 speed
- 5.18.4 multicast-data-rate
- 5.18.5 channel
- 5.18.6 transmit-power
- 5.18.7 radio-mode
- 5.18.8 preamble
- 5.18.9 antenna control
- 5.18.10 antenna id
- 5.18.11 antenna location
- 5.18.12 beacon-interval
- 5.18.13 dtim-period
- 5.18.14 fragmentation-length
- 5.18.15 rts-threshold
- 5.18.16 super-g
- 5.18.17 description
- 5.18.18 ssid
- 5.18.19 closed-system
- 5.18.20 max-association
- 5.18.21 assoc-timeout-interval
- 5.18.22 auth-timeout-value
- 5.18.23 shutdown
- 5.18.24 show interface wireless
- 5.18.25 show station
- 5.19 Rogue AP Detection Commands
- 5.20 Wireless Security Commands
- 5.21 Link Integrity Commands
- 5.22 IAPP Commands
- 5.23 VLAN Commands
- 5.24 WMM Commands
- Appendix A - Troubleshooting
5
Chapter 5 -
Command Line Interface
In This Chapter:
“Using the Command Line Interface” on page 125
“Entering Commands” on page 127
“Command Groups” on page 132
“General Commands” on page 134
“System Management Commands” on page 139
“System Logging Commands” on page 157
“System Clock Commands” on page 162
“DHCP Relay Commands” on page 166
“SNMP Commands” on page 168
“Flash/File Commands” on page 181
“RADIUS Client” on page 185
“802.1X Authentication” on page 191
“MAC Address Authentication” on page 194
“Filtering Commands” on page 198