User's Manual
Table Of Contents
- Compliances
- About This Manual
- Table of Contents
- Chapter 1 - Product Description
- Chapter 2 - Hardware Installation
- 2.1 Hardware Description
- 2.2 Installation Requirements
- 2.3 Installation
- 2.3.1 Attaching the SU-ODU to the Mounting Plate
- 2.3.2 Attaching the Mounting Plate to the Wi· unit
- 2.3.3 Connecting the Wi· unit to the SU-ODU
- 2.3.4 Preparing the Power Cable
- 2.3.5 Pre-Configuration and Testing
- 2.3.6 Mounting the Wi· Unit
- 2.3.7 Connecting the Grounding Cables
- 2.3.8 Connecting to Power Source
- 2.4 Post Installation Configuration of the AP/SU-ODU
- Chapter 3 - Initial Configuration
- Chapter 4 - System Configuration
- 4.1 Introduction
- 4.2 Advanced Configuration
- 4.3 SNMP
- 4.4 Radio Interface
- 4.5 Status Information
- Chapter 5 - Command Line Interface
- 5.1 Using the Command Line Interface
- 5.2 Entering Commands
- 5.2.1 Keywords and Arguments
- 5.2.2 Minimum Abbreviation
- 5.2.3 Command Completion
- 5.2.4 Getting Help on Commands
- 5.2.5 Partial Keyword Lookup
- 5.2.6 Negating the Effect of Commands
- 5.2.7 Using Command History
- 5.2.8 Understanding Command Modes
- 5.2.9 Exec Commands
- 5.2.10 Configuration Commands
- 5.2.11 Command Line Processing
- 5.3 Command Groups
- 5.4 General Commands
- 5.5 System Management Commands
- 5.5.1 country
- 5.5.2 prompt
- 5.5.3 system name
- 5.5.4 username
- 5.5.5 password
- 5.5.6 ip ssh-server enable
- 5.5.7 ip ssh-server port
- 5.5.8 ip telnet-server enable
- 5.5.9 ip http port
- 5.5.10 ip http server
- 5.5.11 ip http session-timeout
- 5.5.12 ip https port
- 5.5.13 ip https server
- 5.5.14 APmgmtIP
- 5.5.15 APmgmtUI
- 5.5.16 show apmanagement
- 5.5.17 show system
- 5.5.18 show version
- 5.5.19 show config
- 5.5.20 show hardware
- 5.6 System Logging Commands
- 5.7 System Clock Commands
- 5.8 DHCP Relay Commands
- 5.9 SNMP Commands
- 5.9.1 snmp-server community
- 5.9.2 snmp-server contact
- 5.9.3 snmp-server location
- 5.9.4 snmp-server enable server
- 5.9.5 snmp-server host
- 5.9.6 snmp-server trap
- 5.9.7 snmp-server engine-id
- 5.9.8 snmp-server user
- 5.9.9 snmp-server targets
- 5.9.10 snmp-server filter
- 5.9.11 snmp-server filter-assignments
- 5.9.12 show snmp groups
- 5.9.13 show snmp users
- 5.9.14 show snmp group-assignments
- 5.9.15 show snmp target
- 5.9.16 show snmp filter
- 5.9.17 show snmp filter-assignments
- 5.9.18 show snmp
- 5.10 Flash/File Commands
- 5.11 RADIUS Client
- 5.12 802.1X Authentication
- 5.13 MAC Address Authentication
- 5.14 Filtering Commands
- 5.15 WDS Bridge Commands
- 5.16 Spanning Tree Commands
- 5.17 Ethernet Interface Commands
- 5.18 Wireless Interface Commands
- 5.18.1 interface wireless
- 5.18.2 vap
- 5.18.3 speed
- 5.18.4 multicast-data-rate
- 5.18.5 channel
- 5.18.6 transmit-power
- 5.18.7 radio-mode
- 5.18.8 preamble
- 5.18.9 antenna control
- 5.18.10 antenna id
- 5.18.11 antenna location
- 5.18.12 beacon-interval
- 5.18.13 dtim-period
- 5.18.14 fragmentation-length
- 5.18.15 rts-threshold
- 5.18.16 super-g
- 5.18.17 description
- 5.18.18 ssid
- 5.18.19 closed-system
- 5.18.20 max-association
- 5.18.21 assoc-timeout-interval
- 5.18.22 auth-timeout-value
- 5.18.23 shutdown
- 5.18.24 show interface wireless
- 5.18.25 show station
- 5.19 Rogue AP Detection Commands
- 5.20 Wireless Security Commands
- 5.21 Link Integrity Commands
- 5.22 IAPP Commands
- 5.23 VLAN Commands
- 5.24 WMM Commands
- Appendix A - Troubleshooting
120 Operation
Chapter 4 - System Configuration
WEP Disabled – The client is not using Wired Equivalent Privacy (WEP)
encryption keys.
Dynamic – The client is using WiFi Protected Access (802.1X or pre-shared
key mode) or using 802.1X authentication with dynamic keying.
Static – The client is using static WEP keys for encryption.
4.5.2.0.1 CLI Commands for Displaying Station Status
To view status of clients currently associated with the access point, use the show
station command from the Exec mode.
4.5.3 Event Logs
The Event Logs window shows the log messages generated by the AP and stored in
memory.
Enterprise AP#show station 224
Station Table Information
===========================================================
if-wireless G VAP [0] :
802.11g Channel : Auto
No 802.11g Channel Stations.
if-wireless G VAP [1] :
802.11g Channel : Auto
No 802.11g Channel Stations.
....
No 802.11g Channel Stations.
if-wireless G VAP [3] :
802.11g Channel : Auto
No 802.11g Channel Stations.
===========================================================
Enterprise AP#