User's Manual

Chapter 10 Deployment Examples (CLI)
160 Aerohive
Step 5Configure the RADIUS Server to accept authentication requests from the HiveAPs
Log in to the RADIUS server and define the three HiveAPs as access devices. Enter their mgt0 IP addresses (or
fully-qualified domain names) and shared secret.
Step 6Check that clients can form associations and access the network
1.To check that a client can associate with a HiveAP and access the network, open a wireless client application
and connect to the "employee" SSID. Then contact a network resource, such as a web server.
2.Log in to the HiveAP CLI, and check that you can see the MAC address or the associated client and an indication
that the correct SSID is in use by entering the following command:
The setup for using IEEE 802.1X is complete. Wireless clients can now associate with the HiveAP using SSID
"employee", authenticate themselves through IEEE 802.1X to a RADIUS server, and access the network.
Note: You can also enter the following commands to check the association status of a wireless client:
show auth, show roaming cache, and show roaming cache mac <mac_addr>.
ݸ»½µ ¬¸¿¬ ¬¸» ÓßÝ ¿²¼ ×Ð
¿¼¼®»--»- ·² ¬¸» ¬¿¾´» ³¿¬½¸
¬¸±-» ±º ¬¸» ©·®»´»-- ½´·»²¬ ò
ݸ»½µ ¬¸¿¬ ¬¸» ¿«¬¸»²¬·½¿¬·±² ¿²¼
»²½®§°¬·±² ³±¼»- ³¿¬½¸ ¬¸±-» ·²
¬¸» ÍÍ×Ü -»½«®·¬§ °®±¬±½±´ -«·¬»ò
-¸±© --
·¼ »³°´±§»» -¬¿¬·±²
ݸ¿²ã½¸¿²²»´ ²«³¾»®å б©ãб©»® ·² ¼Þ³å
ßóÓ±¼»ãß«¬¸»²¬·½¿¬·±² ³±¼»å Ý·°¸»®ãÛ²½®§°¬·±² ³±¼»å
ßóÌ·³»ãß--±½·¿¬»¼ ¬·³»å ß«¬¸ãß«¬¸»²¬·½¿¬»¼å
ËÐ×ÜãË-»® °®±º·´» ×¼»²¬·º·»®å и§³±¼»ãи§-·½¿´ ³±¼»å
Ó¿½ ß¼¼® ×Ð ß¼¼® ݸ¿² ̨ כּ Ψ ο¬» б© ßóÓ±¼» Ý·°¸»® ßóÌ·³» ÊÔßÒ ß«¬¸ ËÐ×Ü Ð¸§³±¼»
óóóóóóóóóóóóóó óóóóóóóóóó óóóó óóóóóóó óóóóóóó óóó óóóóóóóó óóóóóóó óóóóóóóó óóóó óóóó óóóó óóóóóóó
ððïê潺è½æëé¾½ ïðòïòïòéí ï ëìÓ ëìÓ óìð èðîï¨ ¿»- ½½³ ððæðîæíì ï Ç»- ð ïï¾ñ¹
̱¬¿´ -¬¿¬·±² ½±«²¬æ ï