User's Manual

Chapter 10 Deployment Examples (CLI)

154 Aerohive

Step 1Configure HiveAP-1

1.Using the connection settings described in the first example, log in to HiveAP-1.

2.Configure HiveAP-1 as a member of "hive1" and set the security protocol suite.

hive hive1

You create a hive, which is a set of HiveAPs that collectively distribute data and coordinate activities

among themselves, such as client association data for fast roaming, route data for making optimal

data-path forwarding decisions, and policy enforcement for QoS (Quality of Service) and security.

hive hive1 password s1r70ckH07m3s

You define the password that hive members use to derive the preshared key for securing backhaul

communications with each other. The password must be the same on all hive members.

interface mgt0 hive hive1

By setting "hive1" on the mgt0 interface, you join HiveAP-1 to the hive.

save config

3.Before closing the console session, check the radio channel that HiveAP-1 uses on its backhaul interface, which

by default is wifi1:

HiveAP-1 is set to use wireless interface wifi1 and its subinterface wifi1.1 for backhaul communications.

Write down the radio channel for future reference (in this example, it is 149). When configuring

HiveAP-2 and -3, make sure that they also use this channel for backhaul communications.

exit

Ì¸» ©·º·ï ·²¬»®º¿½» ¿²¼ ¬¸» ©·º·ïòï -«¾·²¬»®º¿½» ¿®» ·² ¾¿½µ¸¿«´ ³±¼» ¿²¼

®¿¼·±Á²¿ðò øÜ»°»²¼·²¹ ±² ¬¸» Ø·ª»ßÐ ³±¼»´ô ¬¸» ¼»º¿«´¬ °®±º·´» ³·¹¸¬ ¾»

º®»¯«»²½§ ®¿²¹» ¿- -°»½·º·»¼ ·² ¬¸» ×ÛÛÛ èðîòïï¿ ¿²¼ ² -¬¿²¼¿®¼-ò

-¸±© ·²¬»®º¿½»

Í¬¿¬»ãÑ°»®¿¬·±²¿´ -¬¿¬»å Ý¸¿²ãÝ¸¿²²»´å

Ò¿³» ÓßÝ ¿¼¼® Ó±¼» Í¬¿¬» Ý¸¿² ÊÔßÒ Î¿¼·± Ø·ª» ÍÍ×Ü

óóóóóóó óóóóóóóóóóóóóó óóóóóóóó óóóóó óóóó óóóó óóóóóóóó óóóóó óóóóóóóó

Ó¹¬ð ððïçæééððæððîð ó Ë ó ï ó ¸·ª»ï ó

Û¬¸ð ððïçæééððæððîð ¾¿½µ¸¿«´ Ë ó ï ó ¸·ª»ï ó

É·º·ð ððïçæééððæððîì ¿½½»-- Ë ïï ó ®¿¼·±Á²¹ð ó ó

É·º·ðòï ððïçæééððæððîì ¿½½»-- Ë ïï ó ®¿¼·±Á²¹ð ¸·ª»ï »³°´±§»»

É·º·ï ððïçæééððæððîè ¾¿½µ¸¿«´ Ë ïìç ó ®¿¼·±Á²¿ð ó ó

É·º·ïòï ððïçæééððæððîè ¾¿½µ¸¿«´ Ë ïìç ï ®¿¼·±Á²¿ð ¸·ª»ï ó